Briza SF711A Infrared Patio Heater Instruction Manual

Electric Patio Heater

SF711A Infrared Patio Heater

Estimated time for assembly:
20 mins

TECHNICAL SPECIFICATION

Optimal Operating
Environment| -20 °c – 30 °c
Humidity <85%

When using electrical appliances, basic safety precautions should always be followed including the following:
READ ALL INSTRUCTIONS BEFORE USE AND KEEP THESE INSTRUCTIONS

1. Read all instructions before using this heater.
2. Do not use this heater outdoors.
3. This heater is not intended for use in bathrooms, laundry areas and similar indoor locations. Never locate the heater where it may fall into a bathtub or other water container.
4. Do not run the power cord under carpeting. Do not cover the power cord with throw rugs, runners, or the like. Arrange the power cord away from traffic areas and where it will 0not be tripped over.
5. To disconnect the heater, turn controls to off, then remove the plug from the outlet.
6. Connect to properly grounded outlet only. Always plug heaters directly into a wall outlet/receptacle. Never use with an 0extension cord or reloadable power tap (outlet/power strip).
7. To prevent a possible fire, do not block operate the firebox on soft surfaces, like a bed, where openings may become blocked.
8. There is a thermostat limiter inside the heater. When the inner temperature overheat or abnormal heating occurs, the thermostat protective device cuts off the power supply to avoid fireplace from damaged or risk of fire.
9. Use the heater only as described in the manual. Any other use not recommended by the manufacturer may cause fire, electrical shock, or injury to persons.
10. WARNING: Manufacturer and seller expressly disclaim any and all liability for personal injury, property damage or loss, whether direct, indirect, or incidental, resulting from the incorrect attachment, improper use,inadequate maintenance, unapproved modification, or neglect of this product.

WARNING: There is no user serviceable parts inside fireplace/heater. If the unit appears to malfunction, turn the unit off and unplug from the wall immediately and contact Customer Service.
WARNING: This heater is hot when in use. To avoid burns, do not let bare skin touch hot surfaces. If provided, use handles when moving thos heater. Keep combustible material, such as furniture, pillows, bedding, papers, clothes, and curtains at least 3ft (0.9m) from the front of the heater and keep them away from the side or rear.
WARNING: Extreme caution is necessary when any heater is used by or near children or invalids and whenever the heater is left operating and unattended.
WARNING: Always unplug the heater when not in use.
WARNING: Do not operate any heater with a damaged cord or plug or after the heater malfunctions, has been dropped, or damaged in any manner. Return the heater to an authorized service facility for examination, electrical or mechanical adjustment, or repair.
WARNING: Do not insert or allow foreign objects to enter any ventiliation or exhaust openings as this may cause an electric shock or fire, or damage to the heater.
WARNING: A heater has hot and arching or sparking parts inside. Do not use in areas where gasoline, paint, or flammable liquids are used or stored.
CAUTION: While the heater is in use, the top center of the fireplace can get hot to the touch, and may cause serious injury or burns. Always supervise children around the fireplace/heater. Do not place any cloth or decorations over the heater outlet or fireplace, or otherwise obstruct the heater outlet of the fireplace, as this may cause a fire and serious injury.
Model No.: 050-HA-61000
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
WARNING: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
— Consult the dealer or an experienced radio/TV technician for help.
Read this instruction manual prior to assembly to familiarize yourself with the various steps.
Lay out all components and hardware separately on a flat surface and make sure that no parts are missing or damaged before assembly. Do not destroy or discard any packaging until you are certain that you have all the necessary parts for assembly.
Hand tight all hardwares and careful not to over tighten to avoid damaging the product.
CAUTION
There are small components used in the construction of this product.
Loose items should be kept away from pets and children to avoid a choking hazard.
Keep all plastic bags and packaging film away from pets and children to avoid suffocation.

PACKAGE CONTENTS

ASSEMBLING

Option 1 (wall mounting)

• The back of the fuselage has a wall hanging connection bracket.
• When installing the heater on a wall, the unit should be at least 6 ft (approx 1.8m) above the ground to ensure safety.
• Make sure there is no curtains, clothes, towels, or any combustible materials within 3 ft (approx 1m) of the heating zone of the unit.

Option 2 (Tripod stand)

• The heater can be assemble on top of a tripod stand.
• Assemble a connevting bracket in the rivet nut hole under the fuselage.
• Install the heater on a suitable tripod, with column diameter of at least 35mm.
• The tripod should rated for outdoor use and be able to bear no less than 110 Ib / 50 kg of weight.
• Make sure the heater is not tilted more than 30 degrees in any direction.

USER INSTRUCTION

Before use

• Check that the air intake and exhaust is not covered or obstructed in anyway.
• Keep combustible objects at least 3 ft (0.9 m) away from the unit.
• Plug the unit to a grounded power socket.

Grounding

• This product must be grounded. If it should malfunction or breakdown, grounding provides a path of least resistance for electric current to reduce the risk of electric shock.

CAUTION / WARNING

• Improper connection of the equipment grounding conductor can result ina risk of electric shock. Check with a qualified electrician or serviceman if you are in doubt as to whether the product is properly grounded.
• DONOT modify the plug provided with the product nor using any bypass device if the plug does not fit the outlet. Have a proper outlet installed by a qualified electrician.

USER INSTRUCTION (CONTROL PANEL) Control Panel
The control panel is located on the top right corner of the unit.
Power ON / OFF
The unit will make a beeping sound for 0.5 sec after connected to power. The digital display will displays “– –”
Press and hold the power button for 2 sec to turn on the unit.
Press the power button again to turn off the unit.
CAUTION / WARNING

• DONOT unplug the unit when it is still “ON”

Heater Control Press the heat button to enable the heat function.
“High Heat” is selected by default.
Continue pressing the heat button to cycle through the heat setting.

Timer Control
Press the timer control button to turn the timer on.
Cantine pressing the timer control button to cycle through the timer setting.
Timer interval includes: OH, 1 H,2H,3H,4H,5H,6H,7H,8H,9H.
USER INSTRUCTION (REMOTE CONTROL) Remote Control
The operation of the remote control buttons work the same as the button on the control panel.
The remote control distance is 6ft from the front and 4ft from the sides of the unit.
Power Button
Press power button to turn on the unit.
Press the power button again to turn off the unit.
Heater Button
Press the heater button to enable the heat function.
Timer Control Button
Press the timer control button to cycle through the timer setting.
Time Adjustment Increase / Decrease
Press the increase or decrease button to select different time setting.
Install / Replace Battery
NOTE: The package does not include batteries due to transport safety reasons, please prepare two 1.5V AAA batteries by self

1. Press and slide off the back cover from the remote control.
2. Insert 1.5V AAA batteries into the battery compartment and make sure to install batteries in the correct ploarity.
3. The negative end of the battery should be install against the spring inside the battery compartment.

CAUTION / WARNING

• Dispose old / used battery at a suitable recycling point or according to local regulations.
• DO NOT ingest battery. If accidentally swallowed, seek for medical help immediately.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>