ENERLITES 961243-C-USB Nickel Plated Square Floor Box w TR Outlet Instruction Manual
- June 17, 2024
- ENERLITES
Table of Contents
ENERLITES 961243-C-USB Nickel Plated Square Floor Box w TR Outlet
Product Information
Specifications
- Product Name: 961243-C-USB and 961243-S-USB One Gang Pop-up Floor Box Assembly
- Features: 20A Duplex Tamper Resistant and USB Charger
- Wire Compatibility: 10-12 AWG Stranded or Solid Copper wire
- Depth Requirement: 3/8″ (9mm) for outer tabs
Product Usage Instructions
Floor Box Installation:
- Ensure there is sufficient depth & space below the subfloor.
- Cut out a section of carpet smaller than the size of the cover for carpeted floors.
Wiring Directions:
- Insert the HOT wire to the LINE terminal and tighten the screw.
- Insert the NEUTRAL wire to the NEUTRAL terminal and tighten the screw.
- Insert the GROUND wire to the GREEN terminal and tighten the screw.
Warranty Information:
For warranty details, refer to the product documentation provided with your
purchase.
FAQ
-
Q: Can I use this floor box for outdoor installations?
A: No, this floor box is intended for indoor use only as per safety regulations. -
Q: What should I do if I encounter difficulties during installation?
A: If you face challenges during installation, it is recommended to seek assistance from a qualified electrician to ensure safety and proper functioning.
One Gang Pop-up Floor Box Assembly with 20A Duplex tamper-resistant and USB Charger
SPECIFICATIONS
Cover Material
- 961243……………………………………………………………………………Brass(C) or Nickel-Plated Brass(S)
- Receptacle Rating…………………………………………………………………………………………..20A 125VAC
- Box Material……………………………………………………………………………………………..Galvanized Steel
- Knockout size…………………………………………………………………………………………………1/2″ and 3/4″
- Adjustable Height………………………………………………………………………………………….up to 1″ depth
DESCRIPTION/ FEATURES
Included is a One Gang pop-up floor box with a tamper-resistant 20 amp duplex receptacle with a USB charger.
- Compact and stylish design with adjustable height function metal box with the choice of Brass(C) or Nickel-Plated Brass(S).
- Corrosion-resistant hardware ensures a long life span and reliable performance. Easy access to power when you need it. Snap the cover closed when not in use.
- Used for carpet and wood floors. Also great for countertop applications.
WARNING
Turn the POWER OFF at the circuit breaker before installing the Floor Box
Read and understand these instructions before installing. This device is
intended for installation under the National Electric Code and local
regulations. It is recommended that a qualified electrician perform this
installation. Make sure to turn off the circuit breaker or fuse(s) and make
sure the power is off before wiring the device. Use copper wire only, or
equivalent.
NOTES:
10-12 AWG Stranded or Solid Copper wire is recommended.
FLOOR BOX INSTALLATION
Before Installation:
Ensure there is sufficient depth & space below the subfloor.
Step 1
For carpeted floors:
Cut out a section of carpet smaller than the size of the cover.
For wood sub-floors and finished hardwood floors:
- Tape the template on the area you want to place the floor box.
- Use a knife to cut the outline of the box. Start with the ears and move inwards.
- Following the outline, cut the box shape without the ears completely through the subfloor or hardwood floor.
- Following the outline, cut 3/8″ deep into the subfloor or hardwood for the mounting ears.
- Using a router is recommended
Step 2
- Remove knockouts and secure the box onto the floor. Pull the wires through the opening of the floor and the knockout and connect the wires based on the wiring diagram.
- Use the proper connector/ clamp at the knockouts to secure the wires and to avoid accidental wire stripping.
- Secure the box to the opening using wood screws.
WIRING DIRECTIONS
- Insert the HOT wire into the LINE terminals and tighten the screw.
- Insert the NEUTRAL wire into the NEUTRAL terminal and tighten the screw.
- Insert the GROUND wire into the GREEN terminal and tighten the screw.
WARRANTY INFORMATION
This device is warranted to be free of material and workmanship defects for 2
years from the date of purchase. An original receipt or proof of purchase from
an authorized retailer must be presented upon warranty claim. ALL claims must
be verified and approved by Enerlites, Inc. Warranties from other Enerlites
products may vary. This warranty is non-transferable and does not cover normal
wear and tear or any malfunction, failure, or defect resulting from misuse,
abuse, neglect, alteration, modification, or improper installation. To the
fullest extent permitted by the applicable state law, Enerlites shall not be
liable to the purchaser or end-user customer of Enerlites products for direct,
indirect, incidental, or consequential damages even if Enerlites has been
advised of the possibility of such damages. Enerlites’ total liability under
this or any other warranty, express or implied, is limited to repair,
replacement or refund. Repair, replacement or refund are the sole and
exclusive remedies for breach of warranty or any other legal theory.
© 2019 Enerlites Inc. CA, U.S.A. WWW.ENERLITES.COM
0202190136-02
REV 20230802
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>