ENERLITES 961241-C Brass Square Pop up Floor Box with TRWR Receptacle Instruction Manual
- June 17, 2024
- ENERLITES
Table of Contents
ENERLITES 961241-C Brass Square Pop-up Floor Box with TRWR Receptacle
Product Information
Specifications
Description/Features: One Gang Pop-up Floor Box Assembly with Tamper & Weather Resistant 20A Decorator Duplex Receptacle
Included: One gang pop-up floor box with a tamper & weather resistant 20 amp duplex receptacle, FB-06 box, gasket, and cover
Product Usage Instructions
Floor Box Installation
Before Installation: Ensure there is sufficient depth & space below the subfloor.
Step 1: Preparation
- For carpeted floors: Cut out a section of carpet smaller than the size of the cover.
- Subfloor/Finished Floor Surface: Ensure proper alignment with the subfloor.
WARNING: Turn the POWER OFF at the circuit breaker before installing the Floor Box. Read and understand the instructions before installation. It is recommended that a qualified electrician perform this installation.
Step 2: Wiring Directions
- Connect the HOT wire to the BLACK wire.
- Connect the NEUTRAL wire to the WHITE wire.
- Connect the GROUND wire to the GREEN wire on the switch.
NOTES: 10-12 AWG Stranded or Solid Copper wire is recommended. Route 3/8(10.16mm) Deep For Outer Tabs.
Warranty Information
This product comes with a standard warranty. Contact customer support for details.
FAQ
- Q: Can this floor box assembly be used outdoors?
- A: Yes, this assembly is tamper and weather-resistant, making it suitable for outdoor use.
SPECIFICATIONS
Cover Material
961241……………………………………………………………………………Brass(C) or Nickel-Plated Brass(S)
Receptacle Rating…………………………………………………………………………………………..20A 125VAC
Box Material……………………………………………………………………………………………..Galvanized Steel
Knockout size…………………………………………………………………………………………………1/2″ and 3/4″
Adjustable Height………………………………………………………………………………………….up to 1″ depth
DESCRIPTION/ FEATURES
Included is a One gang pop-up floor box with a tamper & weather resistant 20 amp duplex receptacle, FB-06 box, gasket and cover.
- Compact and stylish design with adjustable height function metal box with the choice of Brass(C) or Nickel-Plated Brass(S).
- Corrosion-resistant hardware ensures long life span and reliable performance. Easy access to power when you need it. Snap the cover closed when not in use.
- Used for carpet and wood floors. Also great for countertop applications.
WARNING
Turn the POWER OFF at the circuit breaker before installing the Floor Box
Read and understand these instructions before installing. This device is
intended for installation in accordance with the National Electric Code and
local regulations. It is recommended that a qualified electrician performs
this installation. Make sure to turn off the circuit breaker or fuse(s) and
make sure power is off before wiring the device. Use copper wire only, or
equivalent.
NOTES:
10-12 AWG Stranded or Solid Copper wire is recommended.
DIMENSIONS
FLOOR BOX INSTALLATION
Before Installation:
Ensure there is sufficient depth & space below the subfloor.
Step 1
For carpeted floors:
Cut out a section of carpet smaller than the size of the cover.
For wood sub-floors and finished hardwood floors:
- Tape the template on the area you want to place the floor box.
- Use a knife to cut the outline of the box. Start with the ears and move inwards.
- Following the outline, cut the box shape without the ears completely through the sub-floor or hardwood floor.
- Following the outline, cut 3/8″ deep into the sub-floor or hardwood for the mounting ears.
- Using a router is recommended
Step 2
- Remove knockouts and secure the box onto the floor. Pull the wires through the opening of the floor and the knockout and connect the wires based on the wiring diagram.
- Use the proper connector/ clamp at the knockouts to secure the wires and to avoid accidental wire stripping.
- Secure the box to the opening using wood screws.
WIRING DIRECTIONS
- Connect the HOT wire to the BLACK wire.
- Connect the NEUTRAL wire to the WHITE wire.
- Connect the GROUND wire to the GREEN wire on the switch.
WARRANTY INFORMATION
This device is warranted to be free of material and workmanship defects for 2 years from the date of purchase. An original receipt or proof of purchase from an authorized retailer must be presented upon warranty claim. ALL claims must be verified and approved by Enerlites, Inc. Warranties from other Enerlites products may vary. This warranty is non-transferable and does not cover normal wear and tear or any malfunction, failure, or defect resulting from misuse, abuse, neglect, alteration, modification, or improper installation. To the fullest extent permitted by the applicable state law, Enerlites shall not be liable to the purchaser or end user customer of Enerlites products for direct, indirect, incidental, or consequential damages even if Enerlites has been advised of the possibility of such damages. Enerlites’ total liability under this or any other warranty, express or implied, is limited to repair, replacement or refund. Repair, replacement or refund are the sole and exclusive remedies for breach of warrantyor any other legal theory.
- 2016 Enerlites Inc. CA, U.S.A.
- WWW.ENERLITES.COM
- 0207160036-01
- REV 20230802
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>