Golden Designs GDI-7202-01 Kuusamo Edition 6 Person Indoor Traditional Steam Sauna Owner’s Manual
- June 17, 2024
- Golden Designs
Table of Contents
GDI-7202-01 Kuusamo Edition 6 Person Indoor Traditional Steam Sauna
“`html
Product Information
Specifications
-
Model Numbers: GDI-7202-01, GDI-7203-01, GDI-7206-01
-
Capacity: 2, 3, and 6 Person Saunas
-
Power Requirements: 240VAC / 1 Phase (30/40AMP for stove),
120VAC 15 AMP for sauna -
Installation: Indoor or outdoor with a water-proof roof
-
Surface: Concrete or tile
Product Usage Instructions
Safety Precautions
1. All electrical wiring must be done by a licensed
electrician.
2. Pay attention to high voltage and general caution
symbols.
Installation
1. Install indoors or under a water-proof structure.
2. Use water tolerable surfaces like concrete or tile.
3. When not in use outdoors, cover the sauna with a waterproof
cover.
Maintenance and Care
1. Do not expose the control system to direct water or rain.
2. Keep the control system well-ventilated and dry.
3. Unplug the unit if not in use for an extended period of
time.
Power Requirements
1. Ensure correct power requirements are met to avoid damage and
injury.
FAQ
Q: Can I install the sauna outdoors without a protective
structure?
A: No, the sauna must be installed indoors or under a protective
structure with a waterproof roof.
Q: What should I do if I encounter an issue with the control
system?
A: Contact the manufacturer for technical assistance or repairs
by authorized technicians only.
“`
GDI-7202-01 / GDI-7203-01 / GDI-7206-01 2, 3 and 6 Person Steam Saunas
OWNER’S MANUAL
FOR STEAM MODEL SAUNAS REQUIRES 240VAC /1PHASE (30/40AMP, depending on your
electrical code) DEDICATED CIRCUIT FOR THE STOVE REQUIRES 120VAC 15 AMP
CIRCUIT FOR THE SAUNA Please Note: The stove must be installed by a certified
electrician per the manufacturer’s manual. The stove must be installed per the
electrical code in your area with reference to the breaker and wire sizes.
Model and parts are subject to change.
1
Thank you for the purchase of your new Steam Sauna! FOLLOW ALL INSTRUCTIONS
AND BE CAUTIOUS OF SAFETY SYMBOLS. All electrical wiring must be performed by
a qualified licensed electrician.
High Voltage Symbol: Be cautious as there is the presence of a high voltage
current that flows through the equipment!
General Caution Symbol: Be cautious as the equipment uses electrical current
that can cause serious injury.
1. Please read this Operating Instruction Manual thoroughly before use. This
will allow the user to become familiar with the operation of the control
system. Please keep the Operating Instruction Manual available for future
reference. If any technical assistance or repairing is needed, please contact
the manufacturer.
2. The steam sauna must be installed indoors or can be installed outdoors
within the protection of a structure that includes a water-proof roof
protecting it from the outdoor weather elements. The sauna must be installed
on water tolerable surfaces such as concrete or tile. When not in use and
placed outdoors, a water proof cover must be used to cover the sauna room.
3. To reduce the risk of electric shock and/or fire, do not expose the
control system to direct water contact or rain. Do not open the cover to the
control system as there are high tension fittings that can be dangerous. Only
dealer authorized qualified technicians should make any needed or necessary
repairs at any time.
4. Any repairs, alterations, or modifications to the control system are not
authorized unless by an approved repair technician. Any non-authorized
repairs, alterations, or modifications can lead to serious injuries and can
cause the unit to work outside its intended specifications parameters.
5. Any non-authorized repairs, alterations, or modifications will void the
warranty. 6. Before connecting the unit to a power source, please make sure
that all wires, cords,
and connections are connected properly. 7. Make sure that the control system
is in a well-ventilated and dry area. Do not place it
next to any heat source, in direct sunlight, where there is any type of
vibration, or in any damp or dusty environment. It should not be place in an
area with other thermalradiating objects. 8. When the equipment is not going
to be used for an extended period of time, unplug the unit from the power
source. 9. Allow 30 seconds between turning the control system “On” and “Off”.
By allowing 30 seconds between powering the control system “On” and “Off” will
prolong the life of the unit.
2
10. Confirm that you adhere to the correct power requirements of the control
system. Connecting the control system to other than the required voltage can
damage the control system and possibly cause serious injury. It is very
important that the load parameters are consistent with that needed by the
control system.
11. Canadian Red Cedar and its rich aroma can cause an extremely small
percentage of the population to have an adverse reaction known as Multiple
Chemical Sensitivity (MCS). While this is not a universally recognized
disorder in the medical field, certain consumers have an adverse physical
reaction to low levels of many common chemicals and cannot tolerate any
aromatic oils, shampoos with perfumes infused or certain herbs with natural
aromas. However, for the majority of the population, Canadian Red Cedar is the
sauna wood of choice.
12. Being that the sauna will operate in different climates (some areas are
colder than others), it is not recommended to use the traditional sauna above
190 degrees Fahrenheit / 88 degrees Celsius.
3
CAUTION: Exit sauna immediately if you feel dizzy, sleepy, or any discomfort.
READ ALL INSTRUCTIONS THOROUGHLY BEFORE ASSEMBLY GDI-7202-01
*The above assembly diagram i s for quick reference only. Read all instructions before assembling. All sauna models may not be shown. Parts and accessories may vary.
4
Schematics
*The above assembly diagram i s for quick reference only. Read all instructions before assembling. All sauna models may not be shown. Parts and accessories may vary.
5
CAUTION: Exit sauna immediately if you feel dizzy, sleepy, or any discomfort.
READ ALL INSTRUCTIONS THOROUGHLY BEFORE ASSEMBLY GDI-7203-01
*The above assembly diagram i s for quick reference only. Read all instructions before assembling. All sauna models may not be shown. Parts and accessories may vary.
6
Schematics
*The above assembly diagram i s for quick reference only. Read all instructions before assembling. All sauna models may not be shown. Parts and accessories may vary.
7
CAUTION: Exit sauna immediately if you feel dizzy, sleepy, or any discomfort.
READ ALL INSTRUCTIONS THOROUGHLY BEFORE ASSEMBLY GDI-7206-01
*The above assembly diagram i s for quick reference only. Read all instructions before assembling. All sauna models may not be shown. Parts and accessories may vary.
8
Schematics
*The above assembly diagram i s for quick reference only. Read all instructions before assembling. All sauna models may not be shown. Parts and accessories may vary.
9
TABLE OF CONTENTS
Product Introduction
10
Wall Panel Descriptions
10
Assembly Instructions
14
Control Panel Operation
22
Tips for Using Your Sauna
24
Safety Instructions
25
Safeguards for Your Sauna
26
Warranty
27
Warranty Card
29
WARNING: Visually inspect all parts before assembly to make sure they are not
damaged. Any excessive vibrations during transport could cause damage to the
sauna components. DO NOT START the sauna if damage is detected! Contact your
dealer or manufacturer for troubleshooting and replacement parts.
PLEASE NOTE: The pictures and diagrams shown within this owner’s manual are
representations of this model. Actual model may vary. Design and construction
are subject to change. The sauna cannot be placed directly in the weather
elements. It is highly recommended to keep the weather elements from reaching
the sauna by placing the sauna under a covered patio or structure with a roof
to fully protect the sauna.
1. Product Introduction The steam sauna room is composed of a wood cabin. The
wood cabin includes a FRONT WALL PANEL with GLASS, REAR WALL PANEL, LEFT SIDE
WALL PANEL, RIGHT SIDE WALL PANEL with Glass, FLOOR PANEL, ROOF, and
BENCHE(S). Other smaller wood items will also be included and can be
identified in the schematics on pages 4, 6, and 8.
2. Wall Panel Descriptions A. The REAR WALL PANEL can be seen in the image
below. It will have the control panel for the radio and lights on the
interior. It will also have the vent to the right of the control panel. (see
Figure 1)
10
Control Panel for Radio & Lights
Vent
Figure 1
B. The LEFT SIDE WALL PANEL will have a vent near the bottom of the wall for the stove ventilation. The RIGHT SIDE WALL PANEL will have a stationary glass panel. The FRONT WALL PANEL will have the GLASS DOOR. (see Figure 2)
Front Glass Door Vent
Vent
Stationary Glass Panel Speaker
Figure 2
NOTE: The pictures and diagrams shown above/below are for representational
purposes only. Actual model may vary. Parts subject to change.
11
Highlights
I. Buckles A.
External Buckles
The external buckles are used to connect the LEFT and RIGHT SIDE PANELS to the
REAR PANEL. (see Figure 3)
Figure 3
B. Guide and Guide Inserts The guide and guide inserts are used to connect the
FRONT PANEL to the RIGHT SIDE PANEL and the LEFT SIDE PANEL. (see Figure 4)
Figure 4
II. Panel Descriptions For easier assembly, please understand and distinguish
the differences between each panel. A. Floor Panel The floor panel will be a
lattice piece of wood and it will not cover the entire floor (does not cover
under the bench). (see Figure 5)
12
FLOOR PANEL
Figure 5 B. Understanding the Difference Between the Top and Bottom of
the Wall Panels The (4) Wall Panels will have white plastic feet on the bottom
of the wall panels. (see Figure 6) Plastic Feet are on the Underside of the
Wall Panels
Figure 6
13
Assembly Instructions A. Choose a good location to install the sauna 1. The
location must be dry, leveled, and away from any source of water. 2. The stove
must be installed by a certified electrician. 3. Two adults are required for
installation on model GDI-7289-01 and three adults for installation on models
GDI-7389-01/GDI-7689-01. 4. Wood cabin installation order: FRONT WALL PANEL
LEFT SIDE WALL PANEL RIGHT SIDE WALL PANEL FLOOR PANEL REAR WALL PANEL BENCH
SUPPORT PANELS BENCH BACK BACKREST ROOF PANEL 5. Tools Required: Battery
Operated Screwdriver or Hand-Held Philips Screwdriver, Rubber Mallet, and
Ladder.
B. Installing the FRONT WALL PANEL and LEFT SIDE WALL PANEL 1. Place the FRONT
WALL PANEL upright and in the desired location. Next, stand the LEFT SIDE WALL
PANEL upright and next to the FRONT WALL PANEL. Align the metal Guide Insert
Brackets on the LEFT SIDE WALL PANEL and the FRONT WALL PANEL. Now you will
need to lift the LEFT SIDE WALL PANEL up and onto the FRONT WALL PANEL locking
the metal Guide Insert Brackets into one another. (see Figure 7)
Figure 7
14
C. Installing the RIGHT SIDE WALL PANEL, FLOOR PANEL and REAR WALL PANEL 1.
Place the RIGHT SIDE WALL PANEL upright and next to the FRONT WALL PANEL.
Align the metal Guide Insert Brackets on the RIGHT SIDE WALL PANEL and the
FRONT WALL PANEL. Now you will need to lift the RIGHT SIDE WALL PANEL up and
onto the FRONT WALL PANEL locking the metal Guide Insert Brackets into one
another. Next, place the FLOOR PANEL on the floor and next to the FRONT WALL
PANEL. The REAR WALL PANEL can now be placed up against the RIGHT SIDE WALL
PANEL and LEFT SIDE WALL PANEL. You will use the buckles to latch the REAR
WALL PANEL to both the RIGHT SIDE WALL PANEL and LEFT SIDE WALL PANEL. (see
Figure 8)
Figure 8
D. Installing the SIDE BENCH SUPPORT PANEL, BENCH SUPPORT PANEL, BENCH, and
BACKREST 1. First, you will need to locate the SIDE BENCH SUPPORTS. See Figure
9. The SIDE BENCH SUPPORTS will be the same for sauna models GDI-7202-01 &
GDI-7203-01. The SIDE BENCH SUPPORT for sauna model GDI-7206-01 will be
different. The SIDE BENCH SUPPORT will need to be screwed to the RIGHT SIDE
WALL PANEL using the 1 7/8″ screws. The SIDE BENCH SUPPORT will have
predrilled holes. 15
SIDE BENCH SUPPORTS For GDI-7202-01 & GDI-7203-01
BENCH SUPPORT PANEL will slide within the vertical slot on the SIDE BENCH
SUPPORTS
For GDI-7206-01
Figure 9
2. It is time to locate the BENCH SUPPORT PANEL. Depending on your sauna
model will determine how many BENCH SUPPORT PANELS you have. For sauna models
GDI-7202-01 and GDI-7203-01, you will have only one BENCH SUPPORT PANEL. For
sauna model GDI-7206-01, you will have two BENCH SUPPORT PANELS. The BENCH
SUPPORT PANEL will side downward within the vertical slots on both the LEFT
SIDE WALL PANEL and the SIDE BENCH SUPPORT PANEL(S) (see Figure 10)
16
GDI-7202-01 &
GDI-7203-01
GDI-7206-01
BENCH SUPPORT PANELS
Figure 10
3. See Figure 10 and locate the BACKREST. You will need to screw the BACKREST
to the wood plank on the REAR WALL PANEL. (see Figure 11)
Wood Plank on REAR WALL PANEL Figure 11
Installing BACKREST 17
Predrilled screw holes
I. Installing the GLASS DOOR HANDLE and ROOF PANEL
1. Locate the GLASS DOOR HANDLE. The GLASS DOOR will need to sit between the
plastic washer (on the outside) and the wood handle (on the inside). (see
Figure 12)
2. Place the ROOF PANEL over the wall panels carefully. Be cautious when
feeding the wires for the lights from the REAR WALL PANEL to the top of the
ROOF PANEL. (see Figure 13)
3. Next, carefully slide the ROOF PANEL into place. You will need to connect
the background light wire connections at the REAR WALL PANEL up on the
rooftop. The blue antenna wire can lay across the rooftop. Next, place the
ROOF COVER over the top of the sauna room. When the edges are aligned, screw
the ROOF COVER to the ROOF PANEL with the provided ¾” screws.
4. It is optional to use the 1 7/8″ screws to screw the roof panel to the
side wall panels.
Exterior Side: (metal handle + Metal Ring + Plastic Washer)
Figure 12
Interior Side: (wood handle)
Figure 13
Note: Be sure to remove the black plastic protection corners from around the
glass door corners, if present.
18
J. Installing the Stove Please Note: The stove must be installed by a
certified electrician per the manufacturer’s manual. The stove must be
installed per the electrical code in your area with reference to the breaker
and wire sizes & wire material. Be sure to follow the manufacturer’s manual
for proper and safe installation of the stove. For the Harvia The Wall Heater,
it is very important to run the stove power cord through the vent hole in the
wall panel and close the vent before installing the stove as you will not be
able to open the vent once the stove is installed. See Figure 14. After the
stove is mounted, you can install the wood housing for the stove. The wood
housing does vary in styles.
Vent Hole
Figure 14
1. First, you will need to locate the wood housing for the stove and assemble
it using the provided screws. (see Figure 15)
Figure 15 19
2. Next, you will need to mount the wood housing to the sauna wall panel
using the provided screws. You will install the wood housing around the stove
as the stove does get very hot. (see Figure 15)
Figure 15
ASSEMBLY COMPLETED!
20
SAUNA CONTROL PANEL – GENERAL INTRODUCTION
1. Description of Functions
Functions
Touch Key technology
FM Radio
Reading Lamp
Background Lamp and Star Lights
Bluetooth Music Play
2. Control System Specifications
A.) Rated Voltage: AC100V-AC240V B.) Bluetooth Approximate Effective Distance:
33 feet C.) Rated Power: 50Hz/60Hz
3. LCD Screen displays the following information:
4. Devices controlled by the Control System are: A.) Reading Lamp B.)
Background Lamp and Star Lights C.) Speaker System
21
5. Control Panel Display
CONTROL PANEL OPERATION
1. ”
“: Powers the unit “ON/OFF”.
A.) Press the ”
” to turn the Control Panel “ON”. The LED will display ”
“,
which means the Control System has powered “ON”. In addition, the Reading Lamp
should be “ON” as well. If you press the ”
” once again, the Control Panel
will turn “OFF”.
B.) The Control System will remain “ON” for 45 minutes. After the 45 minutes has
expired, the Control System will turn “OFF”.
2. ”
“: Powers the Reading Lamp “ON/OFF”.
A.) Press the ”
” to turn the Reading Lamp “ON”. The LED will show ”
“.
Press the ”
” again to turn the Reading Lamp “OFF” and the ”
” will
disappear.
3. ”
“: Powers the Background Lamp and Star Lights “ON/OFF”.
22
A.) Press the ”
” to turn on the Background Lamp and Star Lights. The LED
will show ”
“. Press the ”
” again to turn the Background Lamp and
Star Lights “OFF” and the ”
” will disappear.
4. ”
“: Powers on the Radio and operates the Bluetooth ( ).
A.) Press the ”
” to turn “ON” the FM function of the Radio. The LCD display will
show the current frequency. When you press the ”
” again, you will turn on
the Bluetooth function allowing you to connect your musical device. Once the
Bluetooth is connected to your musical device, the ”
” and ” ” will stop
flashing. If the ”
” and ” ” continue to flash, then your musical device has
not connected to the Bluetooth.
B.) To exit from ”
“, press ”
” a third time.
C.) If you have exited from ”
“, you will need to press the ”
” to
return to the FM function. The FM frequency range is 87.5MHz 108.0MHz. You can
select a FM radio station by pressing ”
” and ”
“. If you press either ” ”
or ”
” for more than 2 seconds, the system will search for radio stations. You will
see the selected radio station on the Control Panel display. If you scroll to the
frequency range limit (say 108.0MHz), press the ” ” again and it will continue to
87.5MHz.
D.) To set the radio station, press the ”
” until you see ” ” flashing on the
Control Panel display. While it is flashing, press the ”
” and ” ” to select the
station you want memorized. Then press ”
” and hold for 3 seconds to store it.
Once stored, you can search the memory to find that stored station. When you are still
in the FM function, press ”
” until the Control Panel displays ” “. Then
press ”
” or ”
” to select a stored station. To exit, press ”
“.
E.) To sink with Bluetooth, search the Bluetooth device name “JOYONWAY”. The password will be “2288” and you should now be able to pair with the device.
23
Once the Bluetooth is connected to your musical device, the ”
” and ” ” will
stop flashing. If the ”
” and ” ” continue to flash, then your musical device
has not connected to the Bluetooth. To disconnect your device from the Bluetooth,
turn off your device and press ”
” for 3 seconds.
F.) To pause the music while your musical device is playing, press ”
” for 3
seconds. Do the same to stop the pause and continue playing music. To play the
previous song or next song, you can press ”
” or ”
“.
G.) The volume adjusting range is from -80dB to 0dB. To adjust the volume, press
”
” until ”
” blinks on the Control Panel display. You can in press the
”
” and ”
” to adjust the volume setting. If you hold the ”
” and
”
” for more than 2 seconds, the volume will increase/decrease at a faster pace.
After 5 seconds, the volume setting will be stored and the function will cancel itself.
Tips for using Your Sauna
-
If you take a hot/warm shower or bath before using your sauna, you may perspire more and experience more comfort.
-
Drink water prior to, during, and after your sauna session to replenish body fluids. 3) To regulate the set temperature inside the sauna to your comfort level, use the movable
ventilation or leave the door open slightly. The ventilation is installed on the sauna and used based on personal preference. 4) Use 2 or 3 towels during your sauna session. Fold one of the towels several times and place it on the bench. This towel will absorb some of your perspiration while adding comfort as you sit on the bench. Place another towel on the floor to absorb perspiration as it falls from your body. Use a third towel to wipe perspiration from your body from time to time. -
At the first sign of a cold or flu, increasing your sauna sessions may be beneficial in boosting your immune system and decreasing the reproductive rate of viruses.
-
To help relieve sore and tense muscles, massage the affected areas during your sauna session. 7) To treat your ankles and feet more effectively, you can elevate them and move them close to one
of the heat emitters to achieve a deep heating effect. 8) The peaceful and relaxed state rendered by a sauna session may help you to sleep easier and
deeper. 9) To protect the life of the stove, you can shut off the circuit breaker when not in use.
24 -
After the sauna session is over, do not jump into the shower or bath immediately. Because your body was heated up during the sauna session, it will continue to perspire even after you exit the sauna room. Sit in the sauna with the door open slightly and let your body cool down. Once your body has cooled down and you feel comfortable, you can exit the sauna. After about twenty minutes and when your body has completely cooled down, you can take a shower to rinse the perspiration off your body.
Safety Instructions
1.) Read and follow all instructions carefully before using the sauna. 2.) When installing and using the electrical equipment, safety precautions should always be followed. 3.) To reduce the risk of injury, do not allow children to use the sauna unless they are directed by a
medical doctor and are closely supervised at all times by an adult. 4.) Do not use the sauna immediately following strenuous exercises. Wait at least 30 minutes to
allow the body to cool down completely. 5.) Pregnant or possibly pregnant women should contact their physician prior to using the sauna.
Excessive temperature has a high potential for causing fetal damage during pregnancy. 6.) Hyperthermia Danger: the normal body temperature can’t rise above 39°C (103°F). Symptoms of
excessive hyperthermia include dizziness, lethargy, drowsiness, and fainting. The effects of excessive hyperthermia may include failure to perceive heat, physical inability to exit sauna, unawareness of impending hazard, unconsciousness and fetal damage in pregnant women. Hyperthermia could make your body’s core temperature rise. Setting desired temperature to an excessively high temperature is not recommended. 7.) The use of alcohol, drugs, or medications prior to or during the sauna session may lead to unconsciousness and/or other harmful physical injuries . 8.) Persons suffering from obesity or with a medical history of heart disease, low or high blood pressure, circulatory system problems, or diabetes should consult a physician prior to using the sauna. 9.) Persons using medications should consult a physician before using the sauna. Some medications may induce drowsiness while others may affect the heart rate, blood pressure, and/or blood circulation. -
Exercise care before and after sauna use. 11) Never sleep inside the sauna. 12) Do not use any type of cleaning agents on the interior of the sauna. Only wipe down with a cloth and water. 13) Do not stack or store any object on top or inside the sauna. 14) If the power supply cord becomes damaged, it must be replaced immediately by the manufacturer or its agent. If you find the power cord is too hot or that the electrical equipment may be experiencing technical problems, please contact the manufacturer or its agent immediately to avoid hazardous conditions. 15) Do not use the sauna during an electrical storm to avoid risk of shock.
25 -
Do not touch the glass door hinges during sauna use as they become very hot to the touch. 17) Your hands must be dry and free of moisture before plugging and unplugging cords and wiring
harnesses from the power supply and circuit boards. Never operate the sauna with wet hands or wet feet to avoid risk of electric shock. Never touch the metal prongs of the plug. 18) Do not attempt to make any repairs yourself without contacting the manufacturer first. If a problem occurs with the sauna, please contact seller, distributor, or the manufacturer to avoid safety risks. Unauthorized repair attempts will void the manufacturer’s warranty. 19) Please make sure the outlet power supply meets the specifications required. Failure to meet the requirements may cause safety risks. 20) Some sauna models are equipped with reading and roof lamps. Because the lamp temperature will become very hot once powered on, do not attempt to touch the lamp to avoid being burned. Do not attempt to touch it for at least 20 minutes after it has been powered off. 21) Do not bump, hit, or break the stove as it may cause an electrical short and pose a safety risk. 22) Do not make any modifications to the sauna, the sauna structure, or the sauna components. 23) Prior to each sauna session, the sauna room is to be inspected for correct operation. If for any reason your sauna room does not seem to be operating properly, discontinue use and contact the manufacturer.
Safeguards For Your Sauna
1. Do not install the sauna near water, near a bathtub, near a shower, in a wet basement, or near a swimming pool.
2. Do not use liquid cleaners or aerosol cleansers inside the sauna. Unplug the sauna from the wall outlet before cleaning. Use plain water and a soft cloth for cleaning.
3. The power supply cord should be routed so that it is not walked on or pinched by any object that may be placed against it.
4. When replacement parts are required, be sure they meet the specified requirements of the manufacturer. Unauthorized substitutes may result in fire, electric shock, or other hazardous conditions. After any repairs, please ask the service technician to perform safety checks to determine that your sauna is working properly.
5. Do not use any wall receptacle adapter or extension cord between the sauna cord and wall receptacle.
26
Limited Lifetime Warranty
*Limited Lifetime Warranty: Golden Designs, Inc. warranties the sauna room and its attached electronics against defects in material and workmanship for the life of the product from the original date of purchase. This sauna is for indoor use or outdoor use when protected from the outdoor weather elements by a structure that includes a water-proof roof. When not in use and placed outdoors, a water proof cover must be used to cover the sauna room or the warranty will become void. Any damage due to direct exposure to outdoor weather elements such as rain, snow, sun, wind or extreme temperatures will not be covered by this warranty. Any damages as a result of modifications made to the sauna or its components will void this warranty.
Extent of Warranty: This limited warranty applies to products manufactured or
distributed by Golden Designs, Inc. under the Golden Designs Inc. brand name,
delivered in the continental United States or Canada and extends to the
original purchaser at the original site of installation only. This warranty
becomes valid at time of purchase and terminates either by specified time
frame, owner transfer, or relocation. The warranty extends to the sauna room
and excludes the stove as it is covered by its own manufacturer warranty. Your
sales receipt showing the date of purchase of the product is your proof of
purchase.
Manufacturer Warranty All Golden Designs, Inc. products are manufactured with
the highest quality appliances and are warranted to be free from defects in
material and workmanship at the time of delivery. The appliance warranty is
extended through the manufacturer for the product including, but not limited
to: sauna control panel and connected wire harnesses. All exchanged parts and
products replaced under this warranty will become the property of Golden
Designs, Inc. Golden Designs, Inc. reserves the right to change for any part
not covered under the existing warranty. Any parts determined to be defective
must be returned to Golden Designs, Inc. at its discretion to obtain warranty
service. You must prepay any shipping charges, export taxes, custom duties and
taxes, or any other charges associated with the transportation of the parts.
In addition you are responsible for insuring any parts shipped or returned.
You must present Golden Designs, Inc. with proof of purchase documents
(including the date of purchase). Any evidence of alteration, erasing or
forgery of proof of purchase documents will be cause to VOID this limited
warranty. Products on which the serial number has been defaced or removed is
not eligible for warranty service.
Warranty Limitations This warranty does not apply if the unit has been subject
to full commercial use, negligence, alteration, modification, misuse, abuse,
repairs by non-Golden Designs, Inc. authorized personnel, inappropriate
installations, or any case beyond the control of Golden Designs, Inc.
invalidating this warranty including but are not limited to:
Use of lacquer or paints Sauna and other Golden Designs, Inc. products
accessories placed on non-approved surfaces Outdoor applications when not
protected from outdoor weather elements Normal wear and tear or weathering Use
of product not in accordance with instructions
Surface cracks are not considered defects in material or workmanship, as they
are normal characteristics of all woods. This includes minor cracks due to
wood expansion and contraction. Note:
27
Since the wood used in construction has been kiln dried, a certain amount of
expansion and contraction occurs in the wood in a sauna environment.
Disclaimers Golden Designs, Inc. shall not be liable for loss of use of sauna
or other Golden Designs, Inc. products or other secondary or incidental or
consequential costs, expense or damages – which may include the removal of
permanent structures or other custom fixtures or the necessity for crane
removal – arising directly or indirectly out of the use or inability to use
the product. Any implied warranty shall have duration equal of the applicable
warranty stated above. Under no circumstances shall Golden Designs, Inc. or
any of its representatives be held liable for injury to any person or damage
to any property, however arising. Specifications are subject to change without
notice or obligation. Legal Remedies This limited warranty gives you specific
legal rights. You may have other rights, which may vary from state to state.
Customer Service For customer service, contact your authorized dealer. If you
need additional information or assistance, please email Golden Designs, Inc.
at info@goldendesignsinc.com or call
909-212-5555.
*Limited Lifetime Warranty of Sauna Products is 7 years on wood structure, control panel, and applicable control panel harnesses and lights from the date of purchase. Stove/heater is covered under its manufacturer’s applicable warranty.
28
WARRANTY CARD
Congratulations on your purchase of an Infrared Sauna from Golden Designs,
Inc. Please take the time to complete the following Warranty Card and mail it
back to:
Golden Designs, Inc. 3550 Jurupa Street, Unit B
Ontario, CA 91761
Please include a copy of your sales receipt showing date of purchase as this
will serve as proof of purchase.
Warranty will be VOID if the following warranty card is not mailed back within
60 days of purchase date along with proof of purchase.
Serial number (S/N) is located on the sauna’s front panel, rear panel, or on
the carton.
DETACH HERE
WARRANTY CARD
All fields must be completed to validate the warranty.
Name: Address: City: Phone Number: Purchase Date: Product Name: Purchase From: Serial Number:
State:
Zip Code:
29
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>