AXXESS XSVI-1731-NAV Honda Civic LX Data Interface 2016 Up Instruction Manual

: June 17, 2024
: AXXESS

Table of Contents

XSVI-1731-NAV
Read User Manual Online (PDF format)
Download This Manual (PDF format)

XSVI-1731-NAV

INSTALLATION INSTRUCTIONS

Honda Civic LX Data Interface 2016-Up

Visit AxxessInterfaces.com for more detailed information about the product and up-to-date vehicle specific applications.

INTERFACE FEATURES

Designed for Non-Amplified vehicles
Provides NAV outputs (parking brake, reverse, and speed sense)
Pre-wired AXSWC harness included (AXSWC sold separately)
Retains the factory backup camera
Retains balance and fade
Includes the AXCSD-6V 12-volt to 6-volt converter
Micro B USB updatable

INTERFACE COMPONENTS

XSVI-1731-NAV interface
XSVI-1731-NAV harness
AXCSD-6V 12-volt to 6-volt converter

APPLICATIONS

HONDA
Civic LX………………………………………….2016-up

TOOLS REQUIRED

• Wire cutter • Crimp tool • Solder gun • Tape
• Connectors (example: butt-connectors, bell caps, etc.)

ATTENTION: With the key out of the ignition, disconnect the negative battery terminal before installing this product. Ensure that all installation connections, especially the air bag indicator lights, are plugged in before reconnecting the battery or cycling the ignition to test this product.
NOTE: Refer also to the instructions included with the aftermarket accessory before installing this device.

CONNECTIONS: LD-XSVI-1731-NAV HARNESS

Steering Wheel Control (AXSWC)
(Sold Separately)
Interface
12-Pin
LD-XSVI-1731-NAV
Aftermarket Radio
(Your radio’s features may vary)
Vehicle Connectors
Radio Connections
Black – Ground wire
Yellow – Battery wire
Red – Accessory power
Green – Rear left speaker + output
Green/Black -Rear left – speaker output
Green/Purple -Reverse backup camera
Light Green – Parking brake
Orange – Illumination
Blue/Pink – VSS/Speed-Sense
Gray – Front right + speaker
Gray/Black – Front right – speaker
White – Front left + speaker
White/Black – Front left – speaker
Purple – Rear right + speaker output
Purple/Black – Rear right – output
After Interface Has Been Programmed: Notes For 2-Pin Connector (E to E1)
RESET AXSWC , and let it program to vehicle and aftermarket radio.
With all connections made, if you do not get correct controls for aftermarket radio, go ahead and disconnect your 2-PinE to E1 and connect E to E2 instead.
Reset and allow the AXSWC to detect your aftermarket radio and controls.
Make sure you get the following Green flashes and Red flashes (1st and 4th Green longer followed by the correct number of Red flashes for aftermarket radio being used. (Refer to Radio LED Feedback Legend on next page.)

AXCSD-6V

Blue/White – Reverse trigger*
Black – Chassis ground
Blue/White – Camera power

Accessory power can also be used if the radio has the option to monitor the camera while in motion.

12-pin pre-wired AXSWC harness:

This harness is to be used along with the optional AXSWC (not included) to retain steering wheel audio controls. If the AXSWC is not being used, disregard this harness. If it will be used, please refer to the AXSWC instructions for radio connections and programming.

Note: Disregard the harness that comes with the AXSWC.

Connect the Red wire to the accessory wire.

2-pin connector ( E TO E1):

RESET AXSWC , and let it program to vehicle and aftermarket radio.

With all connections made, if you do not get correct controls for aftermarket radio, go ahead and disconnect your 2-pin E to E1 and connect E to E2 instead. (See diagram page 2)

Reset and allow the AXSWC to detect your aftermarket radio and controls. Make sure you get the following Green flashes and Red flashes (1st and 4th Green longer followed by the correct number of Red flashes for aftermarket radio being used ( Refer to Radio LED Feedback Legend at right.)

RADIO FEEDBACK LEGEND & DIAGRAM

L.E.D. Feedback: The (23) Red L.E.D. flashes represent a different radio manufacturer for the AXSWC interface to detect. For example, if you are installing a JVC radio, the AXSWC interface will flash Red (5) times, then stop. Following is the L.E.D Feedback Legend , which indicates the flash count of the radio manufacturer

Update Port
Reset Button
(Press and hold for 3 seconds, then release)
Programming LED

L.E.D FEEDBACK LEGEND

Flash Count

| Radio

1

| Eclipse (type 1) †

2

| Kenwood ‡

3

| Clarion (type 1) †

4

| Sony / Dual

5

| JVC

6

| Pioneer / Jensen

7

| Alpine *

8

| Visteon

9

| Valor

10

| Clarion (type 2) †

11

| Metra OE

12

| Eclipse (type 2) †

13

| LG

14

| Parrot **

15

| XITE

16

| Philips

17

| TBA

18

| JBL

19

| Insane

20

| Magnadyne

21

| Boss

22

| Axxera

23

| Axxerra (type 2)

KEYNOTES

If the AXSWC interface flashes Red (7) times, and an Alpine radio is not installed, that means there is an open connection not accounted for. Verify that the 3.5mm jack is connected to the correct steering wheel jack/wire in the radio.

The AXSWCH-PAR** is required (sold separately).
Also, the software in the radio must be rev. 2.1.4 or higher.

† If a Clarion or Eclipse radio is installed and the steering wheel controls do not function, change the radio to Clarion (type 2) or Eclipse (type 2) respectively. If the steering wheel controls still do function, refer to the Changing Radio Type document available at axxessinterfaces.com.

‡ If a Kenwood radio is installed and the L.E.D. feedback flashes (5) times instead of (2), manually change the radio type to Kenwood. To do this, refer to the Changing Radio Type document available at axxessinterfaces.com.

REV. 10/11/23 INSTXSVI-1731-NAV

INSTALLING THE XSVI-1731-NAV

With the key in the off position:

Connect the XSVI-1731-NAV harness into the interface , and then to the harness in the vehicle.

INITIALIZING XSVI-1731-NAV

Attention! If the interface loses power for any reason, the following steps will need to be performed again. Also, if installing an AXSWC connect it after you initialize and test the interface/radio, with the key in the off position.

Turn the key (or push-to-start button) to the ignition position and wait until the radio comes on.
Note: If the radio does not come on within 60 seconds, turn the key to the off position, disconnect the interface, check all connections, reconnect the interface, and then try again.
Turn the key to the off position, and then to the accessory position. Test all functions of the installation for proper operation, before reassembling the dash.

Having difficulties? We’re here to help.

Contact our Tech Support line at:
386-257-1187

Or via email at:
techsupport@metra-autosound.com

Tech Support Hours (Eastern Standard Time)

Monday – Friday: 9:00 AM – 7:00 PM
Saturday: 10:00 AM -5:00 PM
Sunday: 10:00 AM – 4:00 PM

AXXESS - Installer institute

KNOWLEDGE IS POWER
Enhance your installation and fabrication skills by enrolling in the most recognized and respected mobile electronics school in our industry.
Log onto www.installerinstitute.com or call 800-354-6782 for more information and take steps toward a better tomorrow.

AXXESS - MECP certificate Metra recommends MECP certified technicians