YUNZII Royalaxe Y68 Keyboard Gaming User Guide
- June 17, 2024
- YUNZII
Table of Contents
YUNZII Royalaxe Y68 Keyboard Gaming User Guide
DIMENSION INSTRUCTION
Function overview of the keyboard
-
Enter ‘or press Shift at the same time to enter
+: Reset -
FL: F1 function key
+ Screen brightness – -
F2 F2 function key
+ Screen brightness + -
F3: F3 function key
+: Multi screen display -
F4 F4 function key
+ Back to the desktop -
F6: F5 function key
+ Media Player -
F6: F6 function key
+ Play/Pause -
F7: F7 function key
+ Prev song -
F8F8 function key
+ Next song -
F9 F9 function key
G+: Mute -
F10: F10 function key + Volume –
-
F11 F11 function key + Volume +
-
D+F12 F12 function key +AB Input method switching
-
Caps lock indicator
Mode switch -
Wired mode
2.4G wireless mode -
BT Bluetooth mode
-
Bluetooth mode 1
-
Bluetooth mode 2
-
Bluetooth mode 3
-
Ios: Switch to IOS system
-
MAC: Switch to MAC system
-
WIN: Switch to WIN system
-
Fn key (orange)
-
Backlight brightness increase
-
Backlight frequency slows down
-
Backlight frequency slows down
-
Increased backlight frequency
-
Switch the backlight mode Monochromatic light switching
-
Light switch
-
+PgUp PgUp
-
In Insert
-
Fn key (Blue)
-
+Home Home
-
+Pain :PgDn
-
+ End End
-
2.4G receiver
-
ON/OFF power switch
-
Type-C charging/wired interface
Wired connection
-
. Insert the TYPE-C interface of the charging cable into the keyboard, and connect the USB interface to your computer.
-
Rotate to Wired Mode, Mode indicator will flash once and then go out, the connection is successfully completed.
2.4G Connection
-
Turn the power switch to ON.
-
Take out the receiver and insert the receiver into the USB port of the computer.
-
Turn the mode rotary knob to 2.4G mode, the Mode indicator flashes twice and then goes off, the connection is successfully completed.
Bluetooth Connection
-
Turn the power switch to ON. Turn the mode rotary knob to BT mode, the Mode indicator flashes three times and then goes out.
-
Take the connection to BT1 as an example as follows: 2.Long press the Fn (blue) + Q key for about 3-5 seconds, the corresponding indicator light will flash quickly, and then enter the Bluetooth pairing mode.
-
Turn on the Bluetooth of your computer or other device, search and select “Y68 BT3.0” or “Y68 BT5.0” and start Bluetooth pairing until the connection is completed.
Notice :
1. Windows 7 and below system versions do not support Bluetooth 5.0;
2. The device number corresponding to Bluetooths 3.0 is Y68 BT3.0, and the
device number corresponding to Bluetooth 5.0 is Y68 BT5,0
Mode switching method of the keyboard
- Mode channel : The keyboard has 5 channels, BT1, BT2, BT3, 2.4G, wired, and 5 devices can be connected at the same time.
- Mode rotary knob: Turn the mode rotary knob between Wired/2.4G/BT. Press Fn (blue) + Q, W or E to switch between different Bluetooth channels of BT1, BT2 and BT3.
iOS/Mac/Win layout switching Short press to switch system layout.
Note: the default setting is Windows layout
Charging guide:
-
Low voltage reminder. flashes red to remind low voltage.
-
Plug the charging cable TYPE-C interface into the keyboard, USB interface into your computer to start charging red light is always on during charging process
-
indicator turns in green after the charging is completed
NOTE; During the picharorng pros, airy mode is not sented by the “OVOFF with the comply drily siphat by the thanging catte.
Shaft replacement method:
-
Use a keycap puller to unplug the key caps.
-
Pull out the switch with a switch puller.
-
Check the installation position of the switch to be replaced and align the hole positions.
-
Place the new switch on the slot.
-
Gently press the new switch to install it into the slot,
-
Install the keycap, you can use it normally.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>