DYNOJET PC6-16088 Power Commander 6 Installation Guide
- June 4, 2024
- Dynojet
Table of Contents
DYNOJET PC6-16088 Power Commander 6
PARTS LIST
- 1 POWER COMMANDER 6
- 1 INSTALLATION GUIDE
- 1 USB CABLE
- 2 DYNOJET DECALS
- 2 POWER COMMANDER DECALS
- 2 VELCRO STRIPS
- 1 ALCOHOL SWAB
PLEASE READ ALL DIRECTIONS BEFORE STARTING INSTALLATION. THE IGNITION MUST BE TURNED OFF BEFORE INSTALLATION.
INPUT ACCESSORY GUIDE
OPTIONAL ACCESSORY INPUTS
Map
(Input 1 or 2) The PC6 has the ability to hold 2 different base maps. You can
switch on the fly between these two base maps when you hook up a switch to the
MAP inputs. You can use any open/close type switch. The polarity of the wires
is not important.
Shifter
(Input 1 or 2) Used for clutch-less full throttle upshifts. Insert the wires
from the Dynojet quick shifter into either Input 1 or Input 2. The polarity of
the wires is not important. Set to Input 2 by default.
Speed
If your application has a speed sensor then you can tap into the signal side
of the sensor and run a wire into this input. This will allow you to calculate
gear position in the Control Center Software. Once gear position is setup you
can alter your map based on gear position and setup gear dependent kill times
when using a quickshifter. .
Analog
This input is for a 0-5v signal such as engine temp, boost, etc. Once this
input is established you can alter your fuel curve based on this input in the
Power Core software.
Launch
You can connect a wire to either Input 1 or Input 2 and then the other end to
a switch. This switch when engaged (continuity) will only allow the RPM to be
raised to a certain limit (set in the software). When released, you will have
full RPM.
WIRE CONNECTIONS
To input wires into the PC6 first remove the rubber plug on the backside of the unit and loosen the screw for the corresponding input. Using a 22-24 gauge wire, strip about 10mm from its end. Push the wire into the hole of the PC6 until it stops and then tighten the screw. Make sure to reinstall the rubber plug.
NOTE: If you tin the wires with solder it will make inserting them easier.
INSTALLING THE POWER COMMANDER 6
-
Remove the seat, and side panels from both sides.
-
Remove the inner panel from each side of the fuel tank.
-
Install the PC6 in the tail section.
-
Route the PC6 harness down the left side of the frame going towards the throttle body.
-
Attach the ground wire of the PC6 to the negative (-) side of the battery.
-
Locate the crank position sensor wires and unplug them.
The CPS wires are located on the left side of the bike next to the ECU. They are located within a rubber boot and will be the only 2 bullet type connectors. -
Plug the PC6 in-line of the CPS wires.
- PC6 BRN/WHT wire to stock WHT/YEL – WHITE
- PC6 WHT/BRN wire to stock GRN/YEL – BLUE
-
Unplug the stock wiring harness from the injector and Throttle Position Sensor Unplug Unplug
-
Plug the PC6 in-line of the stock injector and wiring harness.
-
Plug the PC6 in-line of the stock TPS and wiring harness.
-
Route the rest of the PC6 harness over to the right side of the motorcycle.
-
Unplug the stock wiring harness from the ignition coil.
-
Connect the PC6 in-line of the stock ignition coil and wiring harness.
- PC6 GREEN wires go to stock GREEN tab of coil
- PC6 RED wires go to stock BLACK tab of coil
-
Reinstall bodywork
ADDRESS: 2191 MENDENHALL DRIVE, NORTH LAS VEGAS, NV 89081
TELL: 800-992-4993
EMAIL: DYNOJET.COM
© 2020-2021 DYNOJET RESEARCH ALL RIGHTS RESERVED
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>