ZIKE Z006 SMART CARD User Manual

**ZIKE Z006 SMART CARD User Manual

**

SAFTY PRECAUTION

1. Do not hit, throw, or puncture the product, and avoid dropping, squeezing, ar bending the product
2. Please avoid high temperature, low temperature, humidity, dusty and long-term exposure to sunlight.
3. Do not place this product in an environment with corrosive substances, and it is strictly forbidden to use other chemical solutions to clean this product.
4. Do not place the product in appliances with strong electromagnetic fields, and keep away from magnetic equipment.
5. Do not disassemble this product, so as not to cause equipment failure

Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential Installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful Interference to radio communications. However, there is no guarantee that Interference will not occur in a particular installation. If this equipment does cause harmful Interference to radio or television reception, which can be determined by turning the equipment off and cn, the user is encouraged to try to correct the Interference by one or more of the following measures:

1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment and receiver
3. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
4. Consult the dealer or an experienced radio/TV technician for help. The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.

INSTRUCTIONS:

Note:

1.  The Smart Card has a built-in 100mAh polymer battery and supports wireless charging. When the iPhone searches for the Smartcard,it will not only make a sound but also have an LED flashing.
2. The Smart Card supports iPhone/iPod models with iOS 14.5 or later,iPad models with iPadOS 14.5 or later, and MAC models with macOS 12.5 or later.(Same as AirTag)

Preparations:

1. Turn on Bluetooth on your iPhone (Settings – Bluetooth – Turn on the switch).
2. Turn on your iPhone -Settings-Notifications-Find My(Turn on Allow Notification).
3. Turn on your iPhone -Settings-Cellular-Find My(WLAN & Cellular Data).
4. Turn on your iPhone -Settings-Privacy-Location Services (turn on the switch).
5. Your iPhone must be logged in with Apple ID.

Connect SmartCard:

1. Power an: Short press you will hear a ringtone)
2. Open “Find My App on your iPhone, allow notifications from the App
3. Select “Items” at the bottom, then click “Add Item and select “Other Supported Items”.
4. It will pop-up “Searching Items”, make sure your Smart Card is close to your iPhone. Wait until you see ZIKE Smart Card, then click “Connect”.
5. Follow the pop-up to fill name, and select an emoji, then dick “Continue”. The name and emoji can be set according to your personal preferences.
6.  When “This item is Linked to Your Apple ID is pop-up, click “Agree (different systems, the displayed information will be different, but this will not affect normal use).
7. Cick “Finish” to finish your Smart Card set-up. After setting up, you can dick Play Sound in the APP to verify whether it is successfully connected to ZIKE Smart Card.

Firmware Upgrade:

1. Click “Available Updates on the page of “Find My App.
2. Click “Update” in the pop-up window.
3. Wait for about 3 minutes until the update is completed.
4. The firmware version will be refreshed automatically, and there will be a beep sound from the anti-lost tracker.

Operations

1. Power one short press the button There will be a brom tO sound when powwing onnot pas a stands and the device flaf intone sounds
2. Power of Press and hold the button fotist 3conds There w beep sounds and blue tasting light, when the device powers t
3. when powering on, short press the button twice. These will be a beep sound:
4. Reset: When connected, short press the button bud on for the Sortiment you to with Press and hold the hasinghe Ths operation wirer all locar panning intumaban and reset the device at the same
5.   Charging： Please use a Qi-compliant wireless charger and align it with the wireless charging position of the anti-lost tracker. Red light is always on when charging. Green light is always on when fully charged.
6. Unpair
7. Unpair iPhone: Make sure that the device is online. In the “Find My” App,click “Remove Devices” at the bottom of the page. Click “Remove” and then continue to click “Remove” until the “Removing Devices” process is complete.At this time, you will hear the unpair prompt sound and the device flashes blue light. The unpairing operation is completed.
8. Unpair and reset: When connected, short press the button ****5 times. Press and hold the button for the 5th time until you hear a reset tone with blue flashing light. At this time, the anti-lost tracker is successfully unpaired.

Main Function:

1. Playing prompt sound:
   a) Click the “Play Sound” in the “Find My” APP: “Play ringtone continuously”for 10 seconds;
   b) Double-click the button of anti-lost tracker when powered on:a“Beep” sound;
   c) After successful unpairing: a short ringtone;
   d) Click the button **of the device when powered off, the device will be turned onwith a short ringtone: the ringtone will be different for paired and unpaired devices.;
   e) When powered on, press and hold the button for at least 3 seconds to turn off the device: “Beep, beep”.
   f) After successfully upgrading the anti-lost tracker firmware through the “Find My” APP: a short ringtone.
   g)** Conditions for APP to play the prompt tone: the anti-lost tracker and the iPhone should be within the distance of Bluetooth communication (maximum connection distance in an open space without too many interfering signals: 50 meters).

2. Track personal belongings through the “Find My” APP – for operation instructions, please refer to the following website:https://support.apple.com/zh-cn/HT211331

3. Locate lost devices or items through the “Find My” App – for operation instructions, please refer to the following website: https://support.apple.com/zh-cn/HT210515

Problems that may be encountered by pairing:

1.  Bring the tracker close to the Phone. The “Find My” APP searches for a long time, but can’t find the tracker (more than 15 seconds). Solutions:
   a) Charge the device with the wireless charger.
   b) Press the power button to turn on the device.
   c) When powered on, short press the button 5 times. Press and hold the button for the 5th time until you hear a beep sound.
   d) Deactivate the network and Bluetooth function in the “Settings” of your iPhone. Turn off the “Find My APP in the background. After 5 seconds, activate your iPhone’s network and then turn on the “Find My” APP to search again,

2. Unable to add new item (several different prompt messages).

3. The “Find My App can find the anti-lost tracker, but the tracker beeps when entering information or waiting for “Setting about to be completed” process.
   2 & 3 Solutions:
   a) The tracker has not been connected before, it is new, or it has been connected before, but the iPhone and the anti-lost tracker have been unpaired;
   b) Fully charge the device via the wireless charger. If you hear a beep sound when pressing the power button , it means the tracker can be normally powered on.
   c) Short press the button 5 times. Press and hold the button for the 5th time until you hear a beep sound.
   d) Check whether the iPhone is available on the network.
   e) Place the iPhone in a good network environment.
   f) Deactivate the network and the Bluetooth function of the iPhone in “Settings”.
   g) Turn off the “Find My” app in the background.
   h) After 5 seconds activate the network and the Bluetooth function of your iPhone again.
   I) Turn on the “Find My” App to search again and connect the device.
   j) If the connection still fails, please go back to step (e) to continue the operation. Sometimes you need to repeat it several times to connect and pair normally.

4. The anti-lost tracker has been paired by other iPhone. The iPhone APP has been not unpaired, nor has the anti-lost tracker been unpaired locally. In this case, the APP can’t find the anti-lost tracker.

5. The anti-lost tracker has been paired by other iPhone. The iPhone APP has been not unpaired, but the anti-lost tracker has been unpaired locally. In this case, the APP can search the anti-lost tracker, but can’t connect to it. Only when the iPhone which is paired to the anti-lost tracker is unpaired in the APP, can the anti-lost tracker been paired.

6. When the new anti-lost tracker is turned on by pressing power button, it prompts “beep beep” sound and can’t be turned on.
   The battery of the device is low. Please fully charge the device through the wireless charger before turning it on and pairing your iPhone.

Notes for unpairing:

1. When the iPhone and the paired anti-lost tracker are within the range of Bluetooth communication (you can click “Play Sound” in the APP to check whether the iPhone is connected to the paired anti-lost tracker). Operation for unpairing: Remove the pairing in the “Find My” APP. After successful removal, the tracker will
   have a successful unpairing prompt sound. At this time, the device can be connected with other iPhone.

2. When the iPhone and the paired anti-lost tracker are not within the range of Bluetooth
   communication Operation for unpairing:
   Step 1: Unpair the paired anti-lost tracker in the “Find My” App.
   Step 2: The anti-lost tracker can be unpaired by local unpairing operation (short press the button 5 times. Press and hold the button for the 5th time until you hear a prompt sound).
   That is to say, the APP on the iPhone should be unpaired and the anti-lost tracker should be unpaired locally. After both sides are successfully unpaired, then the anti- lost tracker can be connected and used by other iPhone. If one side of the device is successfully unpaired and the other side is not, the anti-lost tracker cannot be used by other iPhone.

Other Notes:

1. The time for pairing and unpairing of “Find My” APP fluctuates. This is related to the network speed of the iPhone, the smoothness of the iPhone itself and the signal strength of the anti-lost tracker.

2. Running out of battery doesn’t affect the normal use of the anti-lost tracker. Fully charge the tracker by the wireless charger and then turn it on. Keep your iPhone and anti-lost tracker within the Bluetooth communication range. If you click “Play Sound” in the APP and the “Unable to connect message appears, then click “Play Sound” in the APP several times. At this time, the tracker will play a prompt sound and the “Unable to connect” message will disappear. Since the iPhone and the anti-lost tracker must be connected before the sound can be played properly.

3.  Reasons why the location information and time of the anti-lost tracker are updated slowly or not:
   a) The anti-lost tracker may have been locally unpaired by someone else;
   b) The battery of the anti-lost tracker may be dead;
   c) The device may have been turned off by someone else;
   d) The network, Bluetooth, location services of the paired iPhone may not be turned on;
   e) The anti-lost tracker may have been judged by the APP as being used for tracking others (determined by Apple’s APP algorithm);
   f) The anti-lost tracker may be in a space where the signal is blocked and can’t communicate with other devices;
   g) There may be no other iPhones around the anti-lost tracker, so the location information can’t be reported.

4. If the anti-lost tracker makes a beep sound or no sound when it is turned on, it means that the battery is dead. If there is still no beep sound after charging, the device may be damaged.

5. Since the iPhone and the anti-lost tracker are communicating by Bluetooth, the position error between them is a few meters. Unlike AirTag, which has several centimeters position error, because it has UWB module. In the case of close range, you can click “Play Sound” in the APP to check the exact location of the anti-lost tracker.

6. When the connection between the iPhone and the anti-lost tracker is finished, click “Play Sound” in the APP immediately. Sometimes it will prompt “Unable to connect” and the anti-lost tracker won’t play the sound, which is normal. After a few seconds, click the “Play Sound” in the APP, and the device can play sound properly. After the iPhone is connected to the anti-lost tracker, please wait a few seconds before operating, so that the problem won’t occur.

7. When the connection between the iPhone and the anti-lost tracker is finished, click “Available Updates” in the APP immediately. Sometimes the APP page will be refreshed, but there is no “Update” pop-up window, which is normal. After a few seconds, click “Available Updates” in the APP, and the “Update” pop-up window will appear. After the iPhone is connected to the anti-lost tracker, please wait a few seconds before operating, so that the problem won’t occur

PRODUCT SPECIFICATION:

Smart Card
Model:    Z006
Bluetooth version:    5.2
Frequency range:      2400-2483.5 MHz
Transmission distance:   50m
Frequency response:    2020K Hz
Battery :
Rechargeable lithium battery (100 mAh)
Completion time :   12 months
Waterproof level: IPX7

PACKAGE CONTENTS:
Samrt Card1
User Manual1
Packing Box*1

REGULATORY COMPLIANCE:

FCC

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)This device may not cause harmful interference, and (2)This device must accept any interference received, including interference that may cause undesired operation.

WEEE
For EU(European Union) member users: According to the WEEE(Waste electrical and electronic equipment) Directive, do not dispose of this product as household waste or commercial waste. Waste electrical and electronic equipment should be appropriately collected and recycled as required by practices established for your country. For information on recycling of this product, please contact your local authorities, your household waste disposal service or the shop where you purchased the product.

The Apple Find My network provides an easy, secure way to locate compatible personal items using the Find My app on your iPhone, IPad, Mac, or the Find Items app on Apple Watch.

To use the Apple Find My app to locate this item, the latest version of IOS, iPadOS, or macOS is recommended. The Find Items app on Apple Watch requires the latest version of watchOS.

Use of the Works with Apple badge means that a product has been designed to work specifically with the technology identified in the badge and has been certified by the product manufacturer to meet Apple Find My network product specifications and requirements. Apple is not responsible for the operation of this device or use of this product or its compliance with safety and regulatory standards.

Apple, Apple Find My, Apple Watch, Find My, iPhone, iPad, iPadOS, Mac, macOS and watchOS are the trademarks of Apple Inc. IOS is a trademark or registered trademark of Cisco in the U.S. and other countries and is used under license. The trademark “iPhone” is used with a license from Aiphone K.K.

WWW.ZIKETECH.COM
1(925)639-9430
SUPPORT ZIKETECH.COM

References

• complete.at - This website is for sale! - complete Resources and Information.
• 使用“查找”查找你丢失的 Apple 设备或 AirTag - 官方 Apple 支持 (中国)
• 将 AirTag 添加到“查找”来跟踪个人物品 - 官方 Apple 支持 (中国)

Pages: 1 2

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>