Polk Audio 900-LS 3-Way Loudspeaker Instruction Manual

Polk Audio 900-LS 3-Way Loudspeaker

IMPORTANT SAFETY INSTRUCTIONS

READ BEFORE OPERATING EQUIPMENT

1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings.
8. Install in accordance with the manufacturer’s instructions.
9. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
10. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
11. WARNING: To reduce the risk of fire or electric shock, this apparatus should not be exposed to rain or moisture and objects filled with liquids, such as vases, should not be placed on this apparatus.

Product Disposal

Certain international, national and/or local laws and/ or regulations may apply regarding the disposal of this product. For further detailed information, please contact the retailer where you purchased this product or the Polk Audio Importer/ Distributor in your country. A listing of Polk Audio Importer/Distributors can be found on the Polk Audio website www.polkaudio.com or by contacting Polk Audio at 5601 Metro Drive, Baltimore, Maryland 21215, USA

Phone: +1 410 358-3600.

WARNING: Listen Carefully

Polk Audio loudspeakers and subwoofers are capable of playing at extremely high volume levels, which could cause serious or permanent hearing damage. Polk Audio, Inc. accepts no liability for hearing loss, bodily injury or property damage resulting from the misuse of its products.

Keep these guidelines in mind and always use your own good judgment when controlling volume: You should limit prolonged exposure to volumes that exceed 85 decibels(dB). For more about safe volume levels, go to the Occupational Health and Safety Administration (OSHA) guidelines at http://www.osha.gov/dts/osta/otm/noise/standards_more.html

TAKE INVENTORY

Inside each speaker container, you should find the following:

1. One In-Ceiling Loudspeaker
2. One Sheer-Grille
3. Mounting Template
4. Owner’s Manual
5. Registration Card

Important Note: If anything is missing or damaged, or if your speaker fails to operate, notify Polk Audio Customer Support Services immediately at 800-377-7655.

INSTALLATION RECOMMENDATION

FOR OPTIMUM PERFORMANCE

Important Note: Vanishing Series Loudspeakers are not magnetically shielded and should not be placed closer than 1′ (30cm) from a CRT (tube) television or video monitor.

Important Note: You should have a thorough understanding of and adhere to all local building and fire codes. Also, you should be familiar with the area behind the wall or ceiling into which you plan to install your speakers. Always use wire that meets appropriate building and fire codes. Wiring is best performed by an experienced professional.

When installing your loudspeakers, be aware of the weight of your particular model and the sturdiness of the material into which you are installing the speakers. Be aware of any concealed studs, electrical wiring or plumbing in the wall or ceiling into which you are installing the speakers.

If you doubt that you possess the necessary skills or tools, consult your Polk Audio dealer or a professional installer.

Wire Recommendations

(Minimum recommended)

Runs Gauge

• Lengths up to 25′ 18 or 16
• Lengths greater than 25′ 16 or 14
• But less than 50′
• Lengths greater than 50′ 14 or 12
• But less than 75′
• Lengths greater than 75′ 12

Wall or Ceiling Surface Preparation

If you’re installing your Vanishing Series speaker into a heavily textured wall or ceiling (e.g. stucco or popcorn finish), you must prepare the wall surface immediately around the speaker cutout. Sanding and smoothing the wall or ceiling surface will ensure the speaker and grille both seat properly and flat to the surface.

Loudspeaker Installation

You will need

• Pencil for marking the location of installation.
• Keyhole saw, utility knife or material appropriate tool for cutting drywall or other wall material.
• Screwdriver, preferably powered, with Phillips Head bit.
• Power drill with appropriate bit (optional, for starting wall cut).

Trace around the template

Cut the hole with the appropriate tool

Crossover Warning

• Exercise extreme caution when installing this
• Loudspeaker so you do not damage the crossover.

Security Eyebolt

Your Vanishing Series in-ceiling loudspeaker has an eyebolt on the back of the speaker that can be used for an extra measure of installation security. Follow standard building code installation procedures in your area.

IMPORTANT INFORMATION SHOULD YOU CHOOSE TO PAINT YOUR GRILLES Because of its ultra-thin profile; the Vanishing Series Sheer-Grille™ requires a specific painting procedure to ensure smooth, even coverage.

Important Note: Do not remove the grille scrim before painting.

Paint Recommendation

We highly recommend you use a can of spray paint matched to the ceiling color you want  the Sheer-Grilles to blend with.

Important Note: Never use a brush or   roller to paint the grilles, as this will clog  the perforated holes.

To paint the Sheer-Grille

1. Elevate the Sheer-Grille off of a flat surface. This will ensure even coverage of the grille frame and make it easier to pick up. Mounting Idea: A single spray can cap will raise the grille high enough.

2. Hold the spray paint about 12″ from the grille and at a 45° angle.

3. Apply one light, thin coat, moving evenly side to side over the grille, then work your way around the perimeter of the grille to ensure you cover the grille frame.

4. After each application of paint, wait approximately 1 minute, rotate the grille 90°, and apply the next thin coat.
   Important Note: You must rotate the grille 90°. Use your hands to define the next 90°rotation and always rotate the grille in the same direction of travel.

5. Three light, even applications should cover the grille and frame adequately. Remember to work your way around the grille frame to cover it evenly and completely.

1/2″ (215.9mm)

**ROOM ENVIRONMENT CONTROLS**

Room Switch

If your listening room is very reflective, with smooth sheetrock walls, hardwood floors and non-cushioned furniture, the sound will be overly “bright” and unnatural.

Engaging the Room Switch (Reflective) compensates for the effect of reflectivity in a “hard room” by attenuating only the portion of the tweeter response that can cause harshness resulting in listener fatigue. This flattens room response without hindering higher frequency response, for warmer, more realistic sound and more accurate imaging.

If your listening room is not highly reflective, and that is it has curtains, carpeting, and cushioned furniture, leave the Room Switch in its Normal setting (Norm).

Wall Distance Switch (LS models only)

In-ceiling loudspeakers excel when placed more than 2′ (60cm) from side walls. If position limitations demand that in-ceiling loudspeakers be installed closer than 2′ (60cm) from side walls, the proximity of the surface can result in a response “bump” between 50Hz and 200Hz. This can cause in-ceiling speakers to sound “boomy.” The “Wall Distance” switch flattens response and eliminates “boominess” without sacrificing deep bass response, for more lifelike sound.

DIMENSIONS

LS Models| 900-ls| 700-ls| 500-ls
A. Overall Diameter| 9 5/8″ (244.48mm)| 8 1/8″ (206.38mm)| 7 3/4″ (195.58mm)
B. Cutout Diameter| 8 3/16″ (207.95mm)| 6 1/2″ (165.1mm)| 6″ (152.4mm)
C. Product Depth| 9 3/8″ (238.1mm)| 8 1/2″ (215.9mm)| 9 3/8″ (238.1mm)
D. Mounting Depth (using 1/2″ drywall)| 8 7/8″ (225.4mm)| 8″ (203.2mm)| 8 7/8″ (225.4mm)

1/2″ (215.9mm)

Specifications

For complete Vanishing Series specifications, visit www.polkaudio.com

Limited Lifetime Warranty for Polk Audio

Branded In-Wall and In-Ceiling Speakers

Important Note: This lifetime warranty applies only to in-wall and in- ceiling loudspeakers, and passive CSW subwoofers sold after September 9, 2009.

Polk Audio, Inc., (“Polk”) warrants to the original retail purchaser that Polk Audio branded in-wall and in-ceiling speakers, including passive CSW series subwoofers (collectively “product”), will be free from defects in materials and workmanship for the life of the product, under normal use and conditions. Should this product prove to be defective in material or workmanship, Polk will, at its option, (a) repair the product, or (b) replace the product. If the product model is no longer available and cannot be repaired effectively, or replaced with an identical model, Polk may, at its sole and absolute option, replace the unit with a current model of equal or greater value. To obtain warranty service, you may refer to the instructions in your owner’s manual or visit the Polk Audio website at www.polkaudio.com

You may also contact Polk Audio Customer Service at 1-800-377-7655 for instructions on where to send the product. You will be required to provide an original receipt or bill of sale, identifying you as the original purchaser and identifying the purchase made through an authorized Polk retailer. You will need to ship the product, prepaid and insured, together with the proof of purchase to Polk Audio, Inc. 1 Viper Way, Vista, CA 92081. Risk of loss or damage in transit shall be borne by the purchaser. Freight collect shipments will be refused. This warranty is non-transferable and does not apply to any product that has been modified or used in a manner contrary to its intended purpose, and does not cover damage to the product caused by installation or removal of the product.

If modification(s) to a mounting surface are made to product(s) that have been substituted under warranty, Polk assumes no responsibility or liability for any modification made to the mounting surface or otherwise. This limited warranty is void if the product has an altered or missing serial number, or if the product was purchased from someone other than an authorized dealer. This limited warranty is void if the product has been damaged by accident or unreasonable use, neglect, improper service or other causes not arising out of defects in material or construction. Product(s) which are found to be damaged by abuse resulting in thermally damaged voice coils are not covered by this warranty but may be replaced at the sole and absolute discretion of Polk.

This warranty terminates if you sell or otherwise transfer the product to another party. This limited warranty does not cover cosmetic damage, paint damage, damage to other components, parts or premises, or any consequential damages which may result for any reason. This limited warranty does not cover labor costs for the removal and/or reinstallation of the product.

Frequently Asked Questions

With the right wall dimmer, can the LED lights be dimmed?****

No. The LED lights can only be turned on or off; they cannot be dimmed.

Does the light turn on every time the system is turned on or only occasionally?****

Actually, it’s two distinct pieces that are linked together by a few screws. The speaker, which screws onto the back of the lights, has its own set of cables and terminals for producing music, just like any other conventional speaker that is already completed. Two cables are used to power the LEDs inside the lights’ front component.

How is a ceiling speaker powered?****

No, ceiling speakers normally perform as passive speakers, which means they are driven by speaker wires connected to an external amplifier because they lack inbuilt amplifiers. To do this, the binding posts on the amplifier are linked to each ceiling speaker.

Can ceiling speakers be connected to a receiver?****

The likelihood that there won’t be any additional disconnections is increased when the receiver is connected to ceiling speakers. And if your speakers are properly wired, you won’t have any trouble listening to good music for a very long time.

Are the speakers in the ceiling directional?****

Even though the best in-ceiling speakers are directional and still require careful placement for the best audio image, they nonetheless offer a larger average listening area that is appropriate for background music. You can be towards the borders or corners of the room and still get a strong signal.

How should my Polk speakers be connected?****

The SYNC button on each surround speaker needs to be pressed and held for three seconds. The green LED on the back of the surround speaker will begin flashing more quickly when the sound bar is attached, and then it will turn solid green.

To what are ceiling speakers required?****

To power all of the ceiling speakers, an external amplifier must be connected via speaker cable to each one of them. In our opinion, the best multi-room alternative is the Sonos Amp.

Can I connect my TV to my ceiling speakers?****

There will be an audio output attached to every TV. Right now, it’ll probably be a digital optical output. By putting in an analogue wire from your TV to the amplifier and switching to line output on your TV, you may enjoy TV sound through your ceiling speaker system.

How can I connect my amp to my ceiling speakers?****

Drill a hole where the wires can pass through.
Check to see that the amplifier is unplugged, then shut off the breaker.
Install the wiring.
Start connecting the wires to the terminals on the ceiling speakers.
Connect the wires’ other side to the terminals of the amplifier.
Start your breaker and give it a try.

How do I use my ceiling speakers to play music?****

Purchase a multi-zone AV receiver, after which you should attach speaker wires to each speaker with the amp. Selecting an AV receiver with Bluetooth and WiFi built-in will simplify your home audio setup.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>