A-NEUVIDEO ANI-VGA3204 4K HDMI to HDMI Scaler Instruction Manual

A-NEUVIDEO ANI-VGA3204 4K HDMI to HDMI Scaler

Specifications

• Switcher Category: Custom Matrix Switchers
• Signal Input & Output: VGA, RGB, AV
• Remote Control: Yes
• Communication Port: Available

Introduction
The Custom Matrix Switchers are versatile devices designed for efficient signal routing and management. They offer various input and output options, including VGA, RGB, and AV, allowing users to connect multiple sources to multiple displays.

Safety Information
Before operating the equipment, it is important to review and follow the safety instructions provided:

1. Read the manual and all other documentation before using the product.

2. Follow the instructions printed on the unit chassis for proper operation.

3. Avoid spilling liquids on the unit or operating it in wet conditions.

4. Ensure power outlets meet the specified requirements and
   protect the unit from excessive moisture.

5. Do not use chemical solvents or aerosol cleaners to clean the unit; use a clean dry cloth instead.

6. Do not use the unit if the power cord is damaged.

7. Stop using the equipment if any of the following occur:

   • The power supply cord or plug is damaged.
   • Objects have fallen or liquid has been spilled into the equipment.
   • The equipment has been exposed to rain.
   • The equipment does not operate normally or shows a marked change in performance.
   • The equipment has been dropped or the enclosure is damaged.

SAFETY INFORMATION

1. To ensure the best results from this product, please read this manual and all other documentation before operating your equipment. Retain all documentation for future reference.

2. Follow all instructions printed on unit chassis for proper operation.

3. To reduce the risk of fire, do not spill water or other liquids into or on the unit, or operate the unit while standing in liquid.

4. Make sure power outlets conform to the power requirements listed on the back of the unit. Keep unit protected from rain, water and excessive moisture.

5. Do not attempt to clean the unit with chemical solvents or aerosol cleaners, as this may damage the unit. Dust with a clean dry cloth.

6. Do not use the unit if the electrical power cord is frayed or broken. The power supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords and plugs, convenience receptacles, and the point where they exit from the appliance.

7. Do not force switched or external connections in any way. They should all connect easily, without needing to be forced.

8. Always operate the unit with the AC ground wire connected to the electrical system ground. Precautions should be taken so that the means of grounding of a piece of equipment is not defeated.
   AC voltage must be correct and the same as that printed on the rear of the unit. Damage caused by connection to improper AC voltage is not covered by any warranty.

9. Turn power off and disconnect unit from AC current before making connections.

10. Never hold a power switch in the “ON” position.

11. This unit should be installed in a cool dry place, away from sources of excessive heat, vibration, dust, moisture and cold. Do not use the unit near stoves, heat registers, radiators, or other heat producing devices.
    Do not block fan intake or exhaust ports. Do not operate equipment on a surface or in an environment which may impede the normal flow of air around the unit, such as a bed, rug, carpet, or completely enclosed rack. If the unit is used in an extremely dusty or smoky environment, the unit should be periodically “blown free” of foreign dust and matter.

12. To reduce the risk of electric shock, do not remove the cover. There are no user serviceable parts inside. Refer all servicing to qualified service personnel. There are no user serviceable parts inside.

13. When moving the unit, disconnect input ports first, then remove the power cable; finally, disconnect the interconnecting cables to other devices.

14. Do not drive the inputs with a signal level greater than that required to drive equipment to full output.

15. The equipment power cord should be unplugged from the outlet when left unused for a long period of time.

16. Save the carton and packing material even if the equipment has arrived in good condition. Should you ever need to ship the unit, use only the original factory packing.

17. Service Information Equipment should be serviced by qualifier service personnel when:

    • The power supply cord or the plug has been damaged.
    • Objects have fallen, or liquid has been spilled into the equipment.
    • The equipment has been exposed to rain
    • The equipment does not appear to operate normally, or exhibits a marked change in performance
    • The equipment has been dropped, or the enclosure damaged.

Dear Customer

Thank you for purchasing this product. For optimum performance and safety, please read these instructions carefully before connecting, operating or adjusting this product. Please keep this manual for future reference.

INTRODUCTION

SAFETY PRECAUTIONS
Please read all instructions before attempting to unpack, install or operate this equipment and before connecting the power supply.

Please keep the following in mind as you unpack and install this equipment

Always follow basic safety precautions to reduce the risk of fire, electrical shock and injury to persons.

• To prevent fire or shock hazard, do not expose the unit to rain, moisture or install this product near water.
• Never spill liquid of any kind on or into this product.
• Never push an object of any kind into this product through any openings or empty slots in the unit, as you may damage parts inside the unit.
• Do not attach the power supply cabling to building surfaces.
• Use only the supplied power supply unit (PSU). Do not use the PSU if it is damaged.
• Do not allow anything to rest on the power cabling or allow any weight to be placed upon it or any person walk on it.
• To protect the unit from overheating, do not block any vents or openings in the unit housing that provide ventilation and allow for sufficient space for air to circulate around the unit.

DISCLAIMERS

The information in this manual has been carefully checked and is believed to be accurate. We assume no responsibility for any infringements of patents or other rights of third parties which may result from its use.
We assume no responsibility for any inaccuracies that may be contained in this document. We make no commitment to update or to keep current the information contained in this document.
We reserve the right to make improvements to this document and/or product at any time and without notice.

COPYRIGHT NOTICE

No part of this document may be reproduced, transmitted, transcribed, stored in a retrieval system, or any of its part translated into any language or computer file, in any form or by any means — electronic, mechanical, magnetic, optical, chemical, manual, or otherwise — without express written permission and consent
© Copyright 2015. All Rights Reserved.
Version 2.3 JAN 2015

TRADEMARK ACKNOWLEDGMENTS

All products or service names mentioned in this document may be trademarks of the companies with which they are associated.

INTRODUCTION / SWITCHER CATEGORY / CONTENTS

INTRODUCTION

Matrix switch is a high-performance matrix switcher designed for video and audio signal routing. It supports unbalanced audio, Composite, RGBHV (Component), or VGA (DB15).
The excellent quality of this series of matrix switchers comes from using the industry’s best performing IC chips and we design each switcher to ensure the highest signal quality. The VGA and RGBHV switcher has a signal bandwidth of 350MHz (-3db) to support resolution up to 2048×1536 60Hz refresh rate and1280x1024 120Hz refresh rate, meeting the strict requirements of a variety of high quality sources and displays. The Composite video switcher has a signal bandwidth of 100MHz (-3db), supporting a variety of standard video signals but also able to meet the bandwidth requirements of true HDTV.
This series of matrix switcher provides users with a user friendly GUI that supports all versions of Windows OS. This series of switches has a monochrome dot-matrix LCD display, with control via the front panel push buttons or via RS-232 communication interface. The matrix switch can store up to 30 user presets.

SWITCHER CATEGORY

PACKAGE CONTENTS

Before attempting to use this unit, please check the packaging and make sure the following items are contained in the shipping carton:

• Host Device
• RS-232 Cable
• Power Cable
• CD of testing and application software
• User Manual, Certification and Guarantee Card
• Audio connector

SIGNAL INPUT & OUTPUT, REMOTE CONTROL AND COMMUNICATION PORT

• The AV matrix series switchers support standard BNC connectors; VGA matrix uses standard VGA HD15F connectors; RGBHV matrix uses standard BNC.
• All matrix series uses standard RS-232 serial communication interface DP9-F, in addition to the included GUI software, this document explains the ASCII protocol command set.
• Audio connections use a terminal block, commonly call Pheonic Connector.

TYPES OF MATRIX SWITCHERS

VGA

Model#| Signal Type| Input Connection Type| # of Inputs| Output Connection Type| # of Outputs
---|---|---|---|---|---
ANI-VGA404| VGA| HD15| 4| HD15| 4
ANI-VGA404A| VGA w/Audio| HD15 & Terminal| 4| HD15 & Terminal| 4
ANI-VGA801| VGA| HD15| 8| HD15| 1
ANI-VGA801-A| VGA w/Audio| HD15 & Terminal| 8| HD15 & Terminal| 1
ANI-VGA802 (1RU)| VGA| HD15| 8| HD15| 2
ANI-VGA802-A| VGA w/Audio| HD15 & Terminal| 8| HD15 & Terminal| 2
ANI-VGA 804| VGA| HD15| 8| HD15| 4
ANI-VGA804-A| VGA w/Audio| HD15 & Terminal| 8| HD15 & Terminal| 4
ANI-VGA 808| VGA| HD15| 8| HD15| 8
ANI-VGA808-A| VGA w/Audio| HD15 & Terminal| 8| HD15 & Terminal| 8
ANI-VGA1602| VGA| HD15| 16| HD15| 2
ANI-VGA1602-A| VGA w/Audio| HD15 & Terminal| 16| HD15 & Terminal| 2
ANI-VGA 1604| VGA| HD15| 16| HD15| 4
ANI-VGA1604-A| VGA w/Audio| HD15 & Terminal| 16| HD15 & Terminal| 4
ANI-VGA 1608| VGA| HD15| 16| HD15| 8
ANI-VGA1608-A| VGA w/Audio| HD15 & Terminal| 16| HD15 & Terminal| 8
ANI-VGA 1616| VGA| HD15| 16| HD15| 16
ANI-VGA1616-A| VGA w/Audio| HD15 & Terminal| 16| HD15 & Terminal| 16
ANI-VGA2401| VGA| HD15| 24| HD15| 1
ANI-VGA2402| VGA| HD15| 24| HD15| 2
ANI-VGA 2404| VGA| HD15| 24| HD15| 4
ANI-VGA2404-A| VGA w/Audio| HD15 & Terminal| 24| HD15 & Terminal| 4
ANI-VGA2408| VGA| HD15| 24| HD15| 8
ANI-VGA2408-A| VGA w/Audio| HD15 & Terminal| 24| HD15 & Terminal| 8
ANI-VGA2416| VGA| HD15| 24| HD15| 16
ANI-VGA2416-A| VGA w/Audio| HD15 & Terminal| 24| HD15 & Terminal| 16
ANI-VGA3204| VGA| HD15| 32| HD15| 4
ANI-VGA3204-A| VGA w/Audio| HD15 & Terminal| 32| HD15 & Terminal| 4
ANI-VGA3208| VGA| HD15| 32| HD15| 8
ANI-VGA3208-A| VGA w/Audio| HD15 & Terminal| 32| HD15 & Terminal| 8
ANI-VGA3216| VGA| HD15| 32| HD15| 16
ANI-VGA3216-A| VGA w/Audio| HD15 & Terminal| 32| | 16
ANI-VGA4808| VGA| HD15| 48| HD15| 8
ANI-VGA4816| VGA| HD15| 48| HD15| 16
ANI-VGA7608| VGA| HD15| 76| HD15| 8

COMPOSITE VIDEO

Model#| Signal Type| Input Connection Type| # of Inputs| Output Connection Type| # of Outputs
---|---|---|---|---|---
ANI-V404-A| Composite Video w/Audio| BNC| 4| BNC| 4
ANI-V801-A| Composite Video w/Audio| BNC| 8| BNC| 1
ANI-V802-A| Composite Video w/Audio| BNC| 8| BNC| 2
ANI-V804-A| Composite Video w/Audio| BNC| 8| BNC| 4
ANI-V808-A| Composite Video w/Audio| BNC| 8| BNC| 8
ANI-V1602-A| Composite Video w/Audio| BNC| 16| BNC| 2
ANI-V1604-A| Composite Video w/Audio| BNC| 16| BNC| 4
ANI-V1608-A| Composite Video w/Audio| BNC| 16| BNC| 8
ANI-V1616-A| Composite Video w/Audio| BNC| 16| BNC| 16
ANI-V2408-A| Composite Video w/Audio| BNC| 24| BNC| 8
ANI-V2416-A| Composite Video w/Audio| BNC| 24| BNC| 16
ANI-V2424-A| Composite Video w/Audio| BNC| 24| BNC| 24
ANI-V3208-A| Composite Video w/Audio| BNC| 32| BNC| 8
ANI-V3216-A| Composite Video w/Audio| BNC| 32| BNC| 16
ANI-V3232-A| Composite Video w/Audio| BNC| 32| BNC| 32
ANI-V4816-A| Composite Video w/Audio| BNC| 48| BNC| 16
ANI-V4824-A| Composite Video w/Audio| BNC| 48| BNC| 24
ANI-V4832-A| Composite Video w/Audio| BNC| 48| BNC| 32
ANI-V4848-A| Composite Video w/Audio| BNC| 48| BNC| 48
ANI-V6416-A| Composite Video w/Audio| BNC| 64| BNC| 16
ANI-V6432-A| Composite Video w/Audio| BNC| 64| BNC| 32
ANI-V6448-A| Composite Video w/Audio| BNC| 64| BNC| 48
ANI-V6464-A| Composite Video w/Audio| BNC| 64| BNC| 64
ANI-V12832-A| Composite Video w/Audio| BNC| 128| BNC| 32
ANI-V404| Composite Video| BNC| 4| BNC| 4
ANI-V802| Composite Video| BNC| 8| BNC| 2
ANI-V804| Composite Video| BNC| 8| BNC| 4
ANI-V808| Composite Video| BNC| 8| BNC| 8
ANI-V1604| Composite Video| BNC| 16| BNC| 4
ANI-V1608| Composite Video| BNC| 16| BNC| 8
ANI-V1616| Composite Video| BNC| 16| BNC| 16
ANI-V2416| Composite Video| BNC| 24| BNC| 16
ANI-V3216| Composite Video| BNC| 32| BNC| 16
ANI-V2424| Composite Video| BNC| 24| BNC| 24
ANI-V4816| Composite Video| BNC| 48| BNC| 16
ANI-V4832| Composite Video| BNC| 48| BNC| 32
ANI-V4848| Composite Video| BNC| 48| BNC| 48
ANI-V6416| Composite Video| BNC| 64| BNC| 16
ANI-V6432| Composite Video| BNC| 64| BNC| 32
ANI-V6448| Composite Video| BNC| 64| BNC| 48
ANI-V6464| Composite Video| BNC| 64| BNC| 64

RGB/HV

Model#| Signal Type| Input Connection Type| # of Inputs| Output Connection Type| # of Outputs
---|---|---|---|---|---
ANI-RGB404| RGB/HV| BNC| 4| BNC| 4
ANI-RGB404-A| RGB/HV w/Audio| BNC & Terminal| 4| BNC & Terminal| 4
ANI-RGB802| RGB/HV| BNC| 8| BNC| 2
ANI-RGB802-A| RGB/HV w/Audio| BNC & Terminal| 8| BNC & Terminal| 2
ANI-RGB804| RGB/HV| BNC| 8| BNC| 4
ANI-RGB804-A| RGB/HV w/Audio| BNC & Terminal| 8| BNC & Terminal| 4
ANI-RGB808| RGB/HV| BNC| 8| BNC| 8
ANI-RGB808-A| RGB/HV w/Audio| BNC & Terminal| 8| BNC & Terminal| 8
ANI-RGB1604| RGB/HV| BNC| 16| BNC| 4
ANI-RGB1604-A| RGB/HV w/Audio| BNC & Terminal| 16| BNC & Terminal| 4
ANI-RGB1608| RGB/HV| BNC| 16| BNC| 8
ANI-RGB1608-A| RGB/HV w/Audio| BNC & Terminal| 16| BNC & Terminal| 8
ANI-RGB1616| RGB/HV| BNC| 16| BNC| 16
ANI-RGB1616-A| RGB/HV w/Audio| BNC & Terminal| 16| BNC & Terminal| 16
ANI-RGB2408| RGB/HV| BNC| 24| BNC| 8
ANI-RGB2416| RGB/HV| BNC| 24| BNC| 16
ANI-RGB2424| RGB/HV| BNC| 24| BNC| 16
ANI-RGB3216| RGB/HV| BNC| 32| BNC| 16
ANI-RGB3224| RGB/HV| BNC| 32| BNC| 24
ANI-RGB3232| RGB/HV| BNC| 32| BNC| 32
ANI-RGB4816| RGB/HV| BNC| 48| BNC| 16
ANI-RGB4824| RGB/HV| BNC| 48| BNC| 24
ANI-RGB4848| RGB/HV| BNC| 48| BNC| 48
ANI-RGB6416| RGB/HV| BNC| 64| BNC| 16
ANI-RGB6432| RGB/HV| BNC| 64| BNC| 32
ANI-RGB6448| RGB/HV| BNC| 64| BNC| 48
ANI-RGB6464| RGB/HV| BNC| 64| BNC| 64

AUDIO CONNECTIONS

The series matrix switchers with audio input/output supports unbalanced.

VGA MATRIX SWITCHER

FEATURES

• Professional matrix chip with 350MHz (-3dB) bandwidth when fully loaded
• Supports HDTV up to 2048×1536 60Hz refresh rate and 1280×1024 120Hz refresh rate
• The switching status can be read directly from the LCD display
• Remote control via front panel push buttons or RS-232
• Audio follow Video or Audio Break-away
• Device address range is 1-255. Up to 255 devices can be controlled by cascading
• Store 30 preset matrixes
• Matrix control software to manually switch matrix or automatically switch, etc.
• Faster switching speed with delay time less than 100ns
• Standard rack mountable 19-inch chassis

VGA MATRIX SWITCHER

VGA SPECIFICATIONS

0-10MHz (+0.2dB to -0.1dB)
0-120MHz (+6.5dB to -1.0dB)
Input Level:| 0.5Vp-p min, 2.0Vp-p max
Input I/O Impedance:| 75Ω
Brightness Color Interfere:| -68.5dB@5MHz
Echo Wasting:| -85dB@10MHz
SNR (S/N):| 72.8dB
Switch Speed:| Up to 100ns

H &V SYNC Port

| Input level:| 1Vp-p-5Vp-p
Input impedance:| 10KΩ
Output level:| Compatible TTL
Output impedance:| 75Ω
Synchronous polarity:| Following

Audio Port

| Input & Output:| 3.81mm connector
Bandwidth:| 1MHz
Gain:| Unbalanced 0dB (Can be changed), balanced 6dB
SNR (S/N):| 73.5dB (1Vpp) empty-load
Channel isolation:| >76dB @1KHz
Input Impedance:| High resistance, >47KΩ
Output Impedance:| 47Ω
Control Type| Front Panel Push Button
RS-232
Windows based GUI Software
General| Power Supply: AC 85V-265V, 50Hz/60Hz
Power: 20-50W
Size (WxHxD): 19 x 3.5 x 9.4 in (482x89x240mm)
Weight: 9.9 lb / 4.5 kg
MTBF: 30000 hours

Input & Output VGA (HD15Pin) port

Input & Output VGA (HD15Pin) port

Pin| Name| Description| | Pin| Name| Description
1| R| Red signal| 9| NC| Not used
2| G| Green signal| 10| GND| Place
3| B| Blue signal| 11| GND| Place
4| NC| Not used| 12| NC| Not used
5| GND| Place| 13| H SYNC| H SYNR
6| R GND| Red signal ground| 14| V SYNC| V SYNR
7| G GND| Green signal ground| 14| V SYNC| V SYNR
8| B GND| Blue signal ground| 15| NC| Not used

RGB/HV MATRIX SWITCHER

FEATURES

• Professional matrix chip with 350MHz (-3dB) bandwidth when fully loaded

• Supports HDTV up to 2048×1536 60Hz refresh rate and 1280×1024 120Hz refresh rate

• The switching status can be read directly from the LCD display

• Remote control via front panel push buttons or RS-232

• Audio follow Video or Audio Break-away

• Can be used for RGB, RGBHV, YPBPR

• Device address range is 1-255. Up to 255 devices can be controlled by cascading
  Store 30 preset matrixes

• Matrix control software to manually switch matrix or automatically switch, etc.

• Faster switching speed with delay time less than 100ns

• Standard rack mountable 19-inch chassis

• Aluminum chassis to ensure better EMC

RGB/HV MATRIX SWITCHER

RGB Port

| Input & Output:| Standard BNC
---|---|---
Bandwidth:| 350MHz (-3dB)
0-10MHz (+0.2dB to -0.1dB)
0-120MHz (+6.5dB to -1.0dB)
Input Level:| 0.5Vp-p min, 2.0Vp-p max
Input I/O Impedance:| 75Ω
Brightness Color Interfere:| -68.5dB@5MHz
Echo Wasting:| -85dB@10MHz
SNR (S/N):| 72.8dB
Switch Speed:| Up to 100ns
**H &V Port**| Input level:| 1Vp-p – 5Vp-p
Input impedance:| 10KΩ
Output level:| Compatible TTL
Output impedance:| 75Ω
Synchronous polarity:| Following

**Audio Port**

| Input & Output:| 3.81mm connector
Bandwidth:| 1MHz
Gain:| Balanced 0dB
SNR (S/N):| 73.5dB (1Vpp)
Channel isolation:| >76dB @1KHz
Input Impedance:| High resistance, >47KΩ
Output Impedance:| 47Ω
**Control Type| Front Panel Push Button
RS-232
Windows based GUI Software
****General**| Power Supply: AC 85V-265V, 50Hz/60Hz
Power: 25W-100W
Size (WxHxD): 19 x 5.3 x 9.4 in (482x134x240mm)
Weight: 14.3 lbs / 6.5 kg
MTBF: 50000 hours

COMPOSITE VIDEO SWITCHER

FEATURES

• Professional matrix chip with 100MHz (-3dB) bandwidth when fully loaded
• The switching status can be read directly from the LCD display
• Remote control via front panel push buttons or RS-232
• Audio follow Video or Audio Break-away
• Device address range is 1-255. Up to 255 devices can be controlled by cascading
• Store 30 preset matrixes
• Matrix control software to manually switch matrix or automatically switch, etc.
• Faster switching speed with delay time less than 100ns
• Standard rack mountable 19-inch chassis

COMPOSITE VIDEO SPECIFICATIONS

RGB Port

| Input & Output:| BNC connector
---|---|---
**** Bandwidth:| 100MHz (-3dB)
0.5Vp-p Min, 2.0Vp-p Max
75Ω
Input Level:| 1.0Vp-p Min, 2.0Vp-p Max
Input I/O Impedance:| 75Ω
Brightness Color Interfere:| 75dB
Echo Wasting:| 0.23%
SNR (S/N):| 72.8dB
Switch Speed:| Up to 100ns

H &V Port

| Input level:| 1Vp-p-5Vp-p
Input impedance:| 10KΩ
Output level:| Compatible TTL
Output impedance:| 75Ω
Synchronous polarity:| Following
Audio Port| Input & Output:| 3.81mm connector
Bandwidth:| 1MHz
Gain:| Unbalanced 0dB (Can be changed), balanced 6dB
SNR (S/N):| 73.5dB (1Vpp) empty-load
Channel isolation:| >76dB @1KHz
Input Impedance:| High resistance, >47KΩ
Output Impedance:| 47Ω
Control Type| Front Panel Push Button
RS-232
Windows based GUI Software
General| Power Supply: AC 100V-220V, 50Hz/60Hz
Power: 25W-100W
Size (WxHxD): 19 x 3.5 x 9.4 in (482x89x240mm)
Weight: 9.9 lb / 4.5 kg
MTBF: 50000 hours

OPERATION

PRESS KEY OF FUNCTION REGION

NOTE OF FUNCTION KEY

“V, AV, A, VGA”: Model key for choosing VGA, VIDEO, AUDIO, DVI and HDMI, also can switch computer and video sync or separate.

• e.g. 1: Press“1”+“V”+“6”+“ENTER” means sync switching Video input signal (VGA, VIDEO, DVI, HDMI) to output 6
• e.g. 2: Press“2”+“AV”+“4”+“ENTER” means separate switching the Audio/ Video input 2 (VGA, VIDEO, DVI, HDMI) to output 4 e.g. 3: Press“3”+“A” +“5”+“ENTER” means separate switching Video input 3 to output 5
• e.g. 4: Press “3”+“VGA” +“5”+“ENTER” means separate switching computer signal input 3 to output 5

“SAVE”: To save the corresponding connection of the input & output

e.g. 1: Press “SAVE” +“2” +“ENTER” means saving the current status of input & output to storage location 2 while the total up to 30.

OPERATION

PANEL SWITCH

OPERATION FORMAT OF INPUT & OUTPUT SWITCH

• Way like this: “input”+”switch model”+”output”+”enter”
• Input: 9 number on the panel, also can combined two or three numbers together to choose double or triple digital. Switch Model: “A”,”AV”,”V”,”VGA” means switching computer & audio/ computer /Audio
• Output: 9 number on the panel, also can combined two or three numbers together to choose double or triple digital.

OTHER OPERATION

1. Input switch to Output: “input”+“V, AV, A, VGA”+“output”+“ENTER”
2. One input switch to all output: “input”+“V, AV, A, VGA”+“output 0”+“ENTER”
3. Close one output: “input 0”+“V, AV, A, VGA” +“ENTER”
4. Close all output: “0”+“V, AV, A, VGA”+“0”+“ENTER”

PROTOCOL OF SERIAL PORT AND COMMAND CODE

Before using the serial port to control the device, please confirm the following configuration:

FACTORY DEFAULT SETTING FOR RS-232

• Baud Rate: 9600bps
• Data bit: 8 bits
• Parity: None
• Stop Bits: 1
• Flow Control: None

Use a straight RS-232 cable. DO NOT USE null modem cable.

RS-232 PORT

Matrix switcher has two serial ports: RS-232 input port and RS-232 output ports (Figure 1.6-1). The input port is connected to the computer and the output port is connected to other devices that communicate with the computer. If a user wants to control multiple serial devices by a computer or a central controller, you can cascade multiple devices without more serial ports by sending commands to other devices through RS-232 input port and RS-232 output port. Refer figure A and figure B.

PROTOCOL OF SERIAL PORT AND COMMAND CODE

Definition of RS-232 Port COM IN (D-SUB9F)

Definition of RS-232 Port COM OUT (D-SUB9M)

ASCII CODE

3>3…).
All$.| Close all the output ports.
[x1]#.| Switch input port [x1] to output port [x1].
[x1]$.| Close output port [x1].
[x1]V[x2].| Switch video signal of input port [x1] to output port [x2].
[x1]V[x2],[x3],[x4].| Switch video signal of input port [x1] to output port [x2], [x3], [x4].
[x1]A[x2].| Switch audio signal of input port [x1] to output port [x2].
[x1]A[x2],[x3],[x4].| Switch audio signal of input port [x1] to output port [x2], [x3], [x4].
[x1]B[x2].| Switch audio & video signal of input port [x1] to output port [x2].
[x1]B[x2],[x3],[x4].| Switch audio & video signal of input port [x1] to output port [x2], [x3], [x4].
Compatible code| [x1][x2]!| Switch audio & video signal of input port [x1] to output port [x2].
[x1][x2]$| Switch audio signal of input port [x1] to output port [x2].
[x1][x2]%| Switch video signal of input port [x1] to output port [x2].
[x1][x2]&| Switch video signal of input port [x1] to output port [x2].

Note

1. [x1], [x2], [x3] are number of port, its range is 1~4/8/16/24/32/64/96/128/256 (according to different types of matrix). The code cannot be executed if it is out of range.
2. [ and ] in the code are not sending characters.
3. The ending character of each code cannot be omitted, i.e. ”.”, ”,” etc. Be sure it must be an English character.

CODE EXAMPLES

1. Switch an input port to all output ports: [x1]All.
   e.g. : The code to switch input port 3 to all output ports is “3All.”

2. Switch all input ports to corresponding output ports: All#.
   e.g. : The status of AV8x8 matrix after executing the code is: 1->1,2->2,3->3…,8->8

3. Close all output ports: All$.
   e.g. : To close all the output ports, execute ”All$.”.

4. Close one or more output ports: [x]$.
   e.g. : To close output port 5, execute ”5$.”. To close output port 1, 2 and 3, execute ”1,2,3,4$.”.

5. Switch video signal: [x1]V[x2].
   e.g. : To switch video signal of input port 3 to output port 5, execute: ”3V5.” ;To switch video signal of input port 3 to output port 3, 5 and 10, execute: ”3V3,5,10.”.

6. Switch audio signal: [x1]A[x2].
   e.g. : To switch audio signal of input port 5 to output port 6, execute: ”5A6.”; To switch audio signal of input port 12 to output 3, 5 and 10, execute: ”12V3,5,10.”.

7. Switch audio & video signal: [x1]B[x2].
   e.g. : To switch audio & video signal of input port 10 to output port 12, 14 and 15, execute: ”10B12,14,15.”.

TROUBLESHOOTING

• Please check when the following problems occur: When the peripherals connected to the matrix switcher have a ghost image and the display does not generally have problems. The display may not be correctly tuned or quality wire impedance is mismatched by the signal generating double or multiple reflections. Adjust the display or replace the wire to solve the problem.
• In case of color loss or no signal on an Output, check the connecting port.
• When the AV matrix cannot be controlled by RS-232 (PC Serial port), please check the configuration of the port and the connection of the port.
• Switch with no output image: Check corresponding Input signal (can refer to oscilloscope or multimeter), if there’s no Input signal, check the connecting cable, connector, maybe change to another connector.
• Check corresponding Output signal (refer to oscilloscope or multimeter), if there’s no Output signal, check the connecting cable, connector, maybe change to another connector.
• If power light is Off and no display on the LCD check the connection of power. While you may laugh at this, it does happen.
• If the output image shows interference, the input & output devices may not be grounded.
• If you feel electrostatic spark when pulling, inserting audio or video connectors, it is possible the matrix switcher is not properly grounded. Please ground the device(s) or it will easily damage the equipment and reduce the life.
• If LCD displays, the serial port returns code, but there is no video or audio output: The audio and video connector may be loose. The cable may be short-circuited.
• If the AV matrix cannot be controlled by the front panel push buttons or RS-232, the switcher may be damaged.

SOFTWARE OPERATION INSTRUCTION

1. Run the software and the interface is as following:
   

2. Right click “Matrix Fix” and menu appears like

3. Click “Add Device”, a dialog appears. Select serial port number, baud rate and address.

4. Click “OK” to connect the device. After receiving device information, the controlling Interface is done
   
   The left bar displays the name and type of the device connected. The name can be renamed. Right click on the name, a pop menu appears:
   
   Click “Port Name” to change the names of input & output and preset groups. The interface is as following:
   The caption of button on the interface is also changed as shown below:

5. When the device is connected to the software, the connection information is saved. If the number of serial port, the address of the device and the baud rate are not changed, the software can directly display the device information and the status of connection the next time the software starts. To save the device information, click “Matrix Device” and select “Save Device Information” as shown below:

6. Users can switch the input port to more output ports in one time as shown below:
   
   The above operation switches input port 8 to output port 1, 2, 4, 10 and 19 in one time. Click “OK” to execute as shown below:
   

7. Click “Save”, “Read” to operate preset groups. There are altogether 30 preset groups as shown below:
   

TERMS AND CONDITIONS OF USE

PLEASE READ THE FOLLOWING TERMS AND CONDITIONS CAREFULLY BEFORE USING THIS HARDWARE, COMPONENTS AND SOFTWARE PROVIDED BY, THROUGH OR UNDER A-NeuVideo, INC (COLLECTIVELY, THE “PRODUCT”). By using installing or using the Product, you unconditionally signify your agreement to these Terms and Conditions. If you do not agree to these Terms and Conditions, do not use the Product and return the Product to A-NeuVideo, Inc. at the return address set forth on the Product’s packing label at your expense. A-NeuVideo, Inc. may modify these Terms and Conditions at anytime, without notice to you.

RESTRICTIONS ON USE OF THE PRODUCT

• It is your responsibility to read and understand the installation and operation instructions, both verbal and in writing, provided to you with respect to the Product. You are authorized to use the Product solely in connection with such instructions. Any use of the Product not in accordance with such instructions shall void any warranty pertaining to the Product. Any and all damages that may occur in the use of the Product that is not strictly in accordance with such instructions shall be borne by you and you agree to indemnify and hold harmless A-NeuVideo, Inc. from and against any such damage.
• The Product is protected by certain intellectual property rights owned by or licensed to A-NeuVideo. Any intellectual property rights pertaining to the Product are licensed to you by A-NeuVideo, Inc. and/or its affiliates, including any manufacturers or distributors of the Product (collectively, “A-NeuVideo”) for your personal use only, provided that you do not change or delete any proprietary notices that may be provided with respect to the Product.
• The Product is sold to you and any use of any associated intellectual property is deemed to be licensed to you by A-NeuVideo for your personal use only. A-NeuVideo does not transfer either the title or the intellectual property rights to the Product and A-NeuVideo retains full and complete title to the intellectual property rights therein. All trademarks and logos are owned by A-NeuVideo or its licensors and providers of the Product, and you may not copy or use them in any manner without the prior written consent of A-NeuVideo, which consent may be withheld at the sole discretion of A-NeuVideo.
• The functionality and usability of the Product is controlled by A-NeuVideo, Inc. from its offices within the State of Texas, United States of America. A-NeuVideo makes no representation that materials pertaining to the Product are appropriate or available for use in other locations other than the shipping address you provided with respect thereto. You are advised that the Product may be subject to U.S. export controls.

Disclaimers and Limitation of Liability

• A-NeuVideo may change or modify the Product at any time, from time to time.
• THE PRODUCT IS PROVIDED “AS IS” AND WITHOUT WARRANTIES OF ANY KIND EITHER EXPRESS OR IMPLIED. A-NEUVIDEO DOES NOT WARRANT OR MAKE ANY REPRESENTATIONS REGARDING THE USE OR THE RESULTS OF THE USE OF THE PRODUCT’S CORRECTNESS, ACCURACY, RELIABILITY, OR OTHERWISE.
• A-NeuVideo has no duty or policy to update any information or statements pertaining to the Product and, therefore, such information or statements should not be relied upon as being current as of the date you use the Product. Moreover, any portion of the materials pertaining to the Product may include technical inaccuracies or typographical errors. Changes may be made from time to time without notice with respect to the Product.

TO THE FULLEST EXTENT PERMISSIBLE PURSUANT TO APPLICABLE LAW, A-NEUVIDEO DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT. A-NEUVIDEO DOES NOT WARRANT THE ACCURACY, COMPLETENESS OR USEFULNESS OF ANY INFORMATION WITH RESPECT TO THE PRODUCT. A-NEUVIDEO DOES NOT WARRANT THAT THE FUNCTIONS PERTAINING TO THE PRODUCT WILL BE ERROR-FREE, THAT DEFECTS WITH RESPECT TO THE PRODUCT WILL BE CORRECTED, OR THAT THE MATERIALS PERTAINING THERETO ARE FREE OF DEFECTS OR OTHER HARMFUL COMPONENTS. A-NEUVIDEO WILL USE ITS REASONABLE EFFORTS TO CORRECT ANY DEFECTS IN THE PRODUCT UPON TIMELY WRITTEN NOTICE FROM YOU NOT TO EXCEED 10 BUSINESS DAYS AFTER RECEIPT BY YOU OF THE PRODUCT, BUT YOU (AND NOT A-NEUVIDEO) ASSUME THE ENTIRE COST OF ALL NECESSARY SERVICING, REPAIR AND CORRECTION THAT WAS CAUSED BY YOU UNLESS OTHERWISE AGREED TO IN A SEPARATE WRITING BY A-NEUVIDEO.
UNDER NO CIRCUMSTANCES, INCLUDING, BUT NOT LIMITED TO, NEGLIGENCE, SHALL A-NEUVIDEO BE LIABLE FOR ANY SPECIAL OR CONSEQUENTIAL DAMAGES THAT RESULT FROM THE USE OF, OR THE INABILITY TO USE THE PRODUCT IN ACCORDANCE WITH ITS SPECIFICATIONS, EVEN IF A-NEUVIDEO OR ITS REPRESENTATIVES HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. IN NO EVENT SHALL A-NEUVIDEO’S TOTAL LIABILITY TO YOU FROM ALL DAMAGES, LOSSES, AND CAUSES OF ACTION (WHETHER IN CONTRACT, OR OTHERWISE) EXCEED THE AMOUNT YOU PAID TO A-NEUVIDEO, IF ANY, FOR THE PRODUCT.

END OF DOCUMENT

Documents / Resources

| A-NEUVIDEO ANI-VGA3204 4K HDMI to HDMI Scaler [pdf] Instruction Manual
ANI-VGA3204 4K HDMI to HDMI Scaler, ANI-VGA3204, 4K HDMI to HDMI Scaler, HDMI to HDMI Scaler, HDMI Scaler, HDMI Scaler
---|---

References

• A-NeuVideo.com
• Manual-Hub.com – Free PDF manuals!

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>