AOC Q2770PQU LCD Monitor User Manual
- June 17, 2024
- AOC
Table of Contents
Q2770PQU LCD Monitor
Product Information
Specifications:
-
Model Numbers: E2770SD, E2770SHE, E2770PQU, Q2770PQU, G2770PQU,
M2770V, M2870V, M2870VHE, M2870VQ, I2770V, I2770VHE, I2770PQ -
Backlight Type: LED
Product Usage Instructions:
Safety:
The monitor should be operated only from the type of power
source indicated on the label. If you are not sure of the type of
power supplied to your home, consult your dealer or local power
company.
The monitor is equipped with a three-pronged grounded plug, a
plug with a third (grounding) pin. This plug will fit only into a
grounded power outlet as a safety feature. If your outlet does not
accommodate the three-wire plug, have an electrician install the
correct outlet, or use an adapter to ground the appliance safely.
Do not defeat the safety purpose of the grounded plug.
Unplug the unit during a lightning storm or when it will not be
used for long periods of time. This will protect the monitor from
damage due to power surges.
Do not overload power strips and extension cords. Overloading
can result in fire or electric shock. The wall socket shall be
installed near the equipment and shall be easily accessible.
Installation:
Do not place the monitor on an unstable cart, stand, tripod,
bracket, or table. If the monitor falls, it can injure a person and
cause serious damage to this product. Use only a cart, stand,
tripod, bracket, or table recommended by the manufacturer or sold
with this product. Follow the manufacturer’s instructions when
installing the product and use mounting accessories recommended by
the manufacturer. A product and cart combination should be moved
with care.
Never push any object into the slot on the monitor cabinet. It
could damage circuit parts causing a fire or electric shock. Never
spill liquids on the monitor.
Do not place the front of the product on the floor. If you mount
the monitor on a wall or shelf, use a mounting kit approved by the
manufacturer and follow the kit instructions. Leave some space
around the monitor as shown below. Otherwise, air-circulation may
be inadequate hence overheating may cause a fire or damage to the
monitor. See below the recommended ventilation areas around the
monitor when the monitor is installed on the wall or on the
stand:
Cleaning:
Clean the cabinet regularly with cloth. You can use
soft-detergent to wipe out the stain, instead of strong-detergent
which will cauterize the product cabinet.
When cleaning, make sure no detergent is leaked into the
product. The cleaning cloth should not be too rough as it will
scratch the screen surface.
Please disconnect the power cord before cleaning the
product.
Other:
If the product is emitting a strange smell, sound, or smoke,
disconnect the power plug IMMEDIATELY and contact a Service
Center.
FAQ:
Q: What should I do if my monitor emits a strange smell, sound,
or smoke?
A: Disconnect the power plug immediately and contact a Service
Center.
E2770SD/E2770SHE/E2770PQU Q2770PQU G2770PQU M2770V/ M2870V/M2870VHE/M2870VQ
I2770V/I2770VHE/I2770PQ
(LED Backlight)
Safety …………………………………………………………………………………………………………………………………………………… 4 National
Conventions………………………………………………………………………………………………………………………..4 Power
…………………………………………………………………………………………………………………………………………….5
Installation………………………………………………………………………………………………………………………………………. 6
Cleaning…………………………………………………………………………………………………………………………………………. 7 Other
……………………………………………………………………………………………………………………………………………… 8
Setup ……………………………………………………………………………………………………………………………………………………9 Content of the
Box ……………………………………………………………………………………………………………………………9 Setup Stand
………………………………………………………………………………………………………………………………….. 10 Adjusting Viewing
Angle………………………………………………………………………………………………………………….. 11 Connecting the
Monitor……………………………………………………………………………………………………………………12 Wall Mounting
……………………………………………………………………………………………………………………………….. 15
Adjusting …………………………………………………………………………………………………………………………………………….. 16 Setting
Optimal Resolution ……………………………………………………………………………………………………………… 16 Windows Vista
…………………………………………………………………………………………………………………………16 Windows XP
……………………………………………………………………………………………………………………………18 Windows
ME/2000……………………………………………………………………………………………………………………19 Windows 8
………………………………………………………………………………………………………………………………20 Hotkeys
………………………………………………………………………………………………………………………………………… 22 Using “MHL(Mobile
High-Definition Link)”Optional ………………………………………………………………………..24 OSD
Setting…………………………………………………………………………………………………………………………………..25 Luminance
……………………………………………………………………………………………………………………………… 26 Image Setup
…………………………………………………………………………………………………………………………… 27 Color
Setup……………………………………………………………………………………………………………………………..28 Picture Boost
………………………………………………………………………………………………………………………….. 29 OSD Setup
…………………………………………………………………………………………………………………………….. 30 Extra
………………………………………………………………………………………………………………………………………31
Exit………………………………………………………………………………………………………………………………………… 32 LED Indicator
………………………………………………………………………………………………………………………………… 33
Driver …………………………………………………………………………………………………………………………………………………. 34 Monitor
Driver ……………………………………………………………………………………………………………………………….. 34 Windows 2000
…………………………………………………………………………………………………………………………34 Windows
ME……………………………………………………………………………………………………………………………34 Windows XP
……………………………………………………………………………………………………………………………35 Windows Vista
…………………………………………………………………………………………………………………………38 Windows 7
………………………………………………………………………………………………………………………………40 Windows 8
………………………………………………………………………………………………………………………………44 i-Menu
………………………………………………………………………………………………………………………………………….. 48 e-Saver
………………………………………………………………………………………………………………………………………… 49 Screen+
……………………………………………………………………………………………………………………………………….. 50
Troubleshoot ……………………………………………………………………………………………………………………………………….. 51
Specification………………………………………………………………………………………………………………………………………… 53
General Specification………………………………………………………………………………………………………………………53 Preset
Display Modes …………………………………………………………………………………………………………………….. 58 Pin
Assignments ……………………………………………………………………………………………………………………………. 61 Plug and
Play…………………………………………………………………………………………………………………………………63
2
Regulation…………………………………………………………………………………………………………………………………………… 64 FCC Notice
…………………………………………………………………………………………………………………………………… 64 WEEE
DeclarationOptional………………………………………………………………………………………………………..65 WEEE
Declaration for IndiaOptional……………………………………………………………………………………………65 EPA Energy
StarOptional…………………………………………………………………………………………………………..66 EPEAT
DeclarationOptional……………………………………………………………………………………………………….66 TCO DOCUMENT
…………………………………………………………………………………………………………………………. 67
Service ……………………………………………………………………………………………………………………………………………….. 68 Warranty
Statement for Europe ……………………………………………………………………………………………………….. 68 Warranty
Statement for Middle East and Africa (MEA) ………………………………………………………………………… 70 AOC
Pixel Policy ISO 9241-307 Class 1 ……………………………………………………………………………………………72
Warranty Statement for North & South America (excluding Brazil)
………………………………………………………… 73
3
Safety
National Conventions
The following subsections describe notational conventions used in this
document. Notes, Cautions, and Warnings Throughout this guide, blocks of text
may be accompanied by an icon and printed in bold type or in italic type.
These blocks are notes, cautions, and warnings, and they are used as follows:
NOTE: A NOTE indicates important information that helps you make better use of
your computer system. CAUTION: A CAUTION indicates either potential damage to
hardware or loss of data and tells you how to avoid the problem. WARNING: A
WARNING indicates the potential for bodily harm and tells you how to avoid the
problem. Some warnings may appear in alternate formats and may be
unaccompanied by an icon. In such cases, the specific presentation of the
warning is mandated by regulatory authority.
4
Power
The monitor should be operated only from the type of power source indicated on
the label. If you are not sure of the type of power supplied to your home,
consult your dealer or local power company.
The monitor is equipped with a three-pronged grounded plug, a plug with a
third (grounding) pin. This plug will fit only into a grounded power outlet as
a safety feature. If your outlet does not accommodate the three-wire plug,
have an electrician install the correct outlet, or use an adapter to ground
the appliance safely. Do not defeat the safety purpose of the grounded plug.
Unplug the unit during a lightning storm or when it will not be used for long
periods of time. This will protect the monitor from damage due to power
surges.
Do not overload power strips and extension cords. Overloading can result in
fire or electric shock. The wall socket shall be installed near the equipment
and shall be easily accessible.
5
Installation
Do not place the monitor on an unstable cart, stand, tripod, bracket, or
table. If the monitor falls, it can injure a person and cause serious damage
to this product. Use only a cart, stand, tripod, bracket, or table recommended
by the manufacturer or sold with this product. Follow the manufacturer’s
instructions when installing the product and use mounting accessories
recommended by the manufacturer. A product and cart combination should be
moved with care.
Never push any object into the slot on the monitor cabinet. It could damage
circuit parts causing a fire or electric shock. Never spill liquids on the
monitor.
Do not place the front of the product on the floor. If you mount the monitor
on a wall or shelf, use a mounting kit approved by the manufacturer and follow
the kit instructions. Leave some space around the monitor as shown below.
Otherwise, air-circulation may be inadequate hence overheating may cause a
fire or damage to the monitor. See below the recommended ventilation areas
around the monitor when the monitor is installed on the wall or on the stand:
6
Cleaning
Clean the cabinet regularly with cloth. You can use soft-detergent to wipe out
the stain, instead of strong-detergent which will cauterize the product
cabinet.
When cleaning, make sure no detergent is leaked into the product. The cleaning
cloth should not be too rough as it will scratch the screen surface.
Please disconnect the power cord before cleaning the product.
7
Other
If the product is emitting a strange smell, sound or smoke, disconnect the
power plug IMMEDIATELY and contact a Service Center.
Make sure that the ventilating openings are not blocked by a table or curtain.
Do not engage the LCD monitor in severe vibration or high impact conditions
during operation. Do not knock or drop the monitor during operation or
transportation. For display with glossy bezel the user should consider the
placement of the display as the bezel may cause disturbing reflections from
surrounding light and bright surfaces.
8
Setup
Content of the Box
Monitor
CD Manual Monitor Base /Stand
Wire holder
MHL cable
Power Cable DVI Cable Analog Cable HDMI Cable USB Cable Audio Cable DP Cable
Not all signal cables (Analog , Audio, DVI, USB, DP, MHLand HDMI cables) will
be provided for all countries and regions. Please check with the local dealer
or AOC branch office for confirmation.
9
Setup Stand
Please setup or remove the Stand following the steps as below. 70S/70V Setup
Remove:
70P Setup:
Remove:
10
Adjusting Viewing Angle
For optimal viewing it is recommended to look at the full face of the monitor,
then adjust the monitor’s angle to your own preference. Hold the stand so you
will not topple the monitor when you change the monitor’s angle. You are able
to adjust the monitor’s angle from -5° to 25 °.
NOTE:Do not adjust the viewing angle over 25 degrees in order to avoid damage.
NOTE:
Do not touch the LCD screen when you change the angle. It may cause damage or
break the LCD screen. Do not put your hand close to the gap between the
monitor and the base to avoid the injury when adjusting the viewing angle.
11
Connecting the Monitor
Cable Connections In Back of Monitor and Computer: 1.
E2770SD/M2770V/M2870V/I2770V
2. E2770SHE
12
3 .E2770PQU
4 .Q2770PQU/G2770PQU
5. M2870VHE / I2770VHE
6. M2870VQ
7. I2770PQ
13
1. Power 2. Analog (D-Sub 15-Pin VGA cable) 3. DVI 4. HDMI 5. Audio in 6.
Earphone out 7. Display port 8. HDMI/MHL 9. USB input 10. USB 2.0×2 11. USB
3.0 12. USB 3.0+ fast charging 13. AC power switch
To protect equipment, always turn off the PC and LCD monitor before
connecting. 1. Connect the power cable to the AC port on the back of the
monitor. 2. Connect one end of the 15-pin D-Sub cable to the back of the
monitor and connect the other end to the
computer’s D-Sub port. 3. (Optional Requires a video card with DVI
port)Connect one end of the DVI cable to the back of the monitor
and connect the other end to the computer’s DVI port. 4. (Optional Requires
a video card with HDMI port) – Connect one end of the HDMI cable to the back
of the
monitor and connect the other end to the computer’s HDMI port. 5. (Optional
Requires a video card with DP port) – Connect one end of the DP cable to the
back of the monitor
and connect the other end to the computer’s DP port. 6. (Optional Requires a
video card with MHL port) – Connect one end of the MHL cable to the back of
the
monitor and connect the other end to the computer’s MHL port. 7.
(Optional)Connect the audio cable to audio in port on the back of the monitor
8. Turn on your monitor and computer. If your monitor displays an image,
installation is complete. If it does not display an image, please refer
Troubleshooting.
14
Wall Mounting
Preparing to Install An Optional Wall Mounting Arm. 70S/70V
70P
This monitor can be attached to a wall mounting arm you purchase separately.
Disconnect power before this procedure. Follow these steps: 1. Remove the
base. 2. Follow the manufacturer’s instructions to assemble the wall mounting
arm. 3. Place the wall mounting arm onto the back of the monitor. Line up the
holes of the arm with the holes in the
back of the monitor. 4. Insert the 4 screws into the holes and tighten. 5.
Reconnect the cables. Refer to the user’s manual that came with the optional
wall mounting arm for
instructions on attaching it to the wall. Noted : VESA mounting screw holes
are not available for all models, please check with the dealer or official
department of AOC.
15
Adjusting
Setting Optimal Resolution
Windows Vista
For Windows Vista: 1 Click START. 2 Click CONTROL PANEL.
3 Click Appearance and Personalization.
4 Click Personalization
16
5 Click Display Settings. 6 Set the resolution SLIDE-BAR to Optimal preset
resolution
17
Windows XP
For Windows XP: 1 Click START.
2 Click SETTINGS. 3 Click CONTROL PANEL. 4 Click Appearance and Themes.
5 Double click DISPLAY.
18
6 Click SETTINGS. 7 Set the resolution SLIDE-BAR to Optimal preset resolution
Windows ME/2000
For Windows ME/2000: 1 Click START. 2 Click SETTINGS. 3 Click CONTROL PANEL. 4
Double click DISPLAY. 5 Click SETTINGS. 6 Set the resolution SLIDE-BAR to
Optimal preset resolution
19
Windows 8
For Windows 8: 1. Right click and click All apps at the bottom-right of the
screen.
2. Set the “View by” to “Category”. 3. Click Appearance and Personalization.
20
4. Click DISPLAY. 5. Set the resolution SLIDE-BAR to Optimal preset
resolution.
21
Hotkeys
E2770SD/M2770V/M2870V/I2770V
1
Source/Auto/Exit
2
Clear Vision/-
3
4:3 or Wide/+
4
Menu/Enter
5
Power
E2770SHE/E2770PQU/Q2770PQU/G2770PQU/M2870VQ/M2870VHE/I2770VHE/I2770PQ
1
Source/Auto/Exit
2
Clear Vision/-
3
Volume/+
4
Menu/Enter
5
Power
22
Clear Vision 1. When there is no OSD, Press the “-” button to activate Clear
Vision. 2. Use the “-” or “+” buttons to select between weak, medium, strong,
or off settings. Default setting is always
“off”.
3. Press and hold “-” button for 5 seconds to activate the Clear Vision Demo,
and a message of “Clear Vision Demo: on” will be display on the screen for a
duration of 5 seconds. Press Menu or Exit button, the message will disappear.
Press and hold “-” button for 5 seconds again, Clear Vision Demo will be off.
Clear Vision function provides the best image viewing experience by converting
low resolution and blurry images into clear and vivid images.
23
Using “MHL(Mobile High-Definition Link)”Optional
1.”MHL” (Mobile High-Definition Link) This feature allows you to enjoy videos
and photos (imported from a connected mobile device that supports MHL) on the
screenof the product. To use the MHL function, you need an MHL-certified
mobile device. You can check if your mobile device is
MHL certified on the device manufacturer’s website. To find a list of MHL-
certified devices, visit the official MHL website
(http://www.mhlconsortium.org). To use the MHL function, the latest version of
software must be installed on the mobile device. On some mobile devices, the
MHL function may not be available depending on the device’s performance or
functionality. Since the display size of the product is larger than those of
mobile devices, the picture quality may degrade. This product is officially
MHL-certified. If you encounter any problem when using the MHL function,
please contact the manufacturer of the mobile device. The picture quality may
degrade when content (imported from the mobile device) with a low Resolution
is played on the product.
Using “MHL” 1. Connect the micro USB port on the mobile device to the [HDMI /
MHL] port on the product using the MHL
cable.
When the MHL cable is used, [HDMI / MHL] is the only port on this monitor that
supports the MHL function. Mobile device must be purchased separately. 2.
Press the source button and switch to HDMI /MHL to activate MHL mode. 3. After
about 3 seconds, the MHL screen will be displayed if MHL mode is active.
Remark: The indicated time “3 sec later” may vary depending on the mobile
device.
When the mobile device is not connected or does not support MHL
If MHL mode is not activated, check the connection of the mobile device. If
MHL mode is not activated, check if the mobile device supports MHL. If MHL
mode is not activated even though the mobile device supports MHL, update the
firmware of the mobile
device to the latest version. If MHL mode is not activated even though the
mobile device supports MHL, check if mobile device MHL port
is MHL standard port otherwise an additional MHL-enabled adapter is required.
24
OSD Setting
Basic and simple instruction on the control keys.
1. Press the MENU-button to activate the OSD window. 2. Press – or + to
navigate through the functions. Once the desired function is highlighted,
press the
MENU-button to activate. Press – or + to navigate through the sub-menu. Once
the desired function is highlighted, press MENU-button to activate. 3. Press –
or + to change the settings of the selected function. Press AUTO to exit. If
you want to adjust any other function, repeat steps 2-3. 4. OSD Lock Function:
To lock the OSD, press and hold the MENU-button while the monitor is off and
then press power-button to turn the monitor on. To un-lock the OSD, press and
hold the MENU-button while the monitor is off and then press power-button to
turn the monitor on. Notes: 1. If the product has only one signal input, the
item of “Input Select” is disabled. 2. If the product screen size is 4:3 or
input signal resolution is wide format, the item of “Image Ratio” is disabled.
3. One of Clear vision, DCR, Color Boost, and Picture Boost functions is
activated; the other three functions are turned off accordingly.
25
Luminance
1 Press
(Menu) to display menu.
2 Press – or + to select
(Luminance), and press
to enter.
3 Press – or + to select submenu, and press 4 Press – or + to adjust.
to enter.
5 Press
to exit.
Brightness Contrast
0-100 0-100
Standard
Text
Eco mode
Internet Game
Movie
Gamma DCR Overdrive
Sports
Gamma1 Gamma2 Gamma3 Off
On
Weak Medium Strong
Off
Backlight Adjustment. Contrast from Digital-register. Standard Mode.
Text Mode.
Internet Mode.
Game Mode.
Movie Mode.
Sports Mode. Adjust to Gamma 1. Adjust to Gamma 2. Adjust to Gamma 3. Disable
dynamic contrast ratio. Enable dynamic contrast ratio. Adjust the response
time (only for E2770PQU/Q2770PQU/G2770PQU/I27 70VHE/M2870VHE/M2870VQ/I2770PQ )
26
Image Setup
1 Press
(Menu) to display menu.
2 Press – or + to select
(Image Setup), and press
3 Press – or + to select submenu, and press
4 Press – or + to adjust.
5 Press
to exit.
to enter.
to enter.
Clock Phase Sharpness H.Position V.Position
0-100 0-100 0-100 0-100 0-100
Adjust picture Clock to reduce Vertical-Line noise. Adjust Picture Phase to reduce Horizontal-Line noise. Adjust picture sharpness. Adjust the horizontal position of the picture. Adjust the vertical position of the picture.
27
Color Setup
1 Press
(Menu) to display menu.
2 Press – or + to select
(Color Setup), and press
3 Press – or + to select submenu, and press
4 Press – or + to adjust.
5 Press
to exit.
to enter.
to enter.
Color Temp.
DCB Mode DCB Demo
Warm Normal Cool sRGB
User
Full Enhance Nature Skin Green Field Sky-blue AutoDetect
Red Green Blue on or off on or off on or off on or off on or off on or off
Recall Warm Color Temperature from EEPROM. Recall Normal Color Temperature from EEPROM. Recall Cool Color Temperature from EEPROM. Recall SRGB Color Temperature from EEPROM. Red Gain from Digital-register. Green Gain Digital- register. Blue Gain from Digital-register. Disable or Enable Full Enhance Mode. Disable or Enable Nature Skin Mode. Disable or Enable Green Field Mode. Disable or Enable Sky-blue Mode. Disable or Enable AutoDetect Mode. Disable or Enable Demo.
28
Picture Boost
1 Press
(Menu) to display menu.
2 Press – or + to select
(Picture Boost), and press
3 Press – or + to select submenu, and press
4 Press – or + to adjust.
5 Press
to exit.
to enter.
to enter.
Frame Size Brightness Contrast H. position V. position Bright Frame
14-100 0-100 0-100 0-100 0-100 on or off
Adjust Frame Size. Adjust Frame Brightness. Adjust Frame Contrast. Adjust Frame horizontal position. Adjust Frame vertical position. Disable or Enable Bright Frame.
29
OSD Setup
1 Press
(Menu) to display menu.
2 Press – or + to select
(OSD Setup), and press
to enter.
3 Press – or + to select submenu, and press 4 Press – or + to adjust.
5 Press
to exit.
to enter.
H. Position V. Position Timeout Transparence Language
0-100 0-100 5-120 0-100
Break Reminder
on or off
Adjust the horizontal position of OSD. Adjust the vertical position of OSD. Adjust the OSD Timeout. Adjust the transparence of OSD. Select the OSD language. Disable or Enable (1 hour of work, break ?) / (2 hours of work, break ?)
30
Extra
1 Press
(Menu) to display menu.
2 Press – or + to select
(Extra), and press
3 Press – or + to select submenu, and press 4 Press – or + to adjust.
5 Press
to exit.
to enter. to enter.
Input Select Input Select Input Select
Input Select
Input Select Auto Config Off timer
Image Ratio
DDC-CI Reset Information
Auto / Analog / DVI / HDMI(MHL) Select input signal source. (E2770PQU) /DP
Auto / Analog / HDMI1/ HDMI2
Select input signal source. (E2770SHE)
Auto / Analog / DVI/HDMI
Select
input
source.(I2770VHE/M2870VHE)
signal
Auto / Analog / DVI
Select input signal source. (E2770SD/M2770V/M2870V/I2770V)
Auto / Analog / DVI / HDMI /DP
Select
input
signal
source.
(Q2770PQU/G2770PQU/M2870VQ/I2770PQ)
yes or no
Auto adjust the picture to default.
0-24hrs
Select DC off time.
wide or 4:3 wide or 4:3/1:1 / 17″(4:3) / 19″w(16:10) / 21.5″(16:9) / 22″w(16:10) / 23″w(16:9) yes or no
Select wide or 4:3 format for display. Select image ratio for display.(G2770PQU) Turn ON/OFF DDC-CI Support.
yes or no
Reset the menu to default.
Show the information of the main image and sub-image source.
31
Exit
1 Press
(Menu) to display menu.
2 Press – or + to select
3 Press
to exit.
(Exit), and press
to enter.
Exit
Exit the main OSD.
32
LED Indicator
Status Full Power Mode Active-off Mode
Green or Blue Orange or red
LED Color
33
Driver
Monitor Driver
Windows 2000
1. Start Windows® 2000 2. Click on the ‘Start’ button, point to ‘Settings’,
and then click on ‘Control Panel’. 3. Double click on the ‘Display’ Icon. 4.
Select the ‘Settings’ tab then click on ‘Advanced…’. 5. Select ‘Monitor’ – If
the ‘Properties’ button is inactive, it means your monitor is properly
configured. Please stop installation. – If the ‘Properties’ button is active.
Click on ‘Properties’ button. Please follow the steps given below. 6. Click on
‘Driver’ and then click on ‘Update Driver…’ then click on the ‘Next’ button.
7. Select ‘Display a list of the known drivers for this device so that I can
choose a specific driver’, then click on ‘Next’ and then click on ‘Have
disk…’. 8. Click on the ‘Browse…’ button then select the appropriate drive F:
( CD-ROM Drive). 9. Click on the ‘Open’ button, then click on the ‘OK’ button.
10. Select your monitor model and click on the ‘Next’ button. 11. Click on the
‘Finish’ button then the ‘Close’ button. If you can see the ‘Digital Signature
Not Found’ window, click on the ‘Yes’ button.
Windows ME
1. Start Windows® Me 2. Click on the ‘Start’ button, point to ‘Settings’, and
then click on ‘Control Panel’. 3. Double click on the ‘Display’ Icon. 4.
Select the ‘Settings’ tab then click on ‘Advanced…’. 5. Select the ‘Monitor’
button, then click on ‘Change…’ button. 6. Select ‘Specify the location of the
driver(Advanced)’ and click on the ‘Next’ button. 7. Select ‘Display a list of
all the drivers in a specific location, so you can choose the driver you
want’, then click on ‘Next’ and then click on ‘Have Disk…’. 8. Click on the
‘Browse…’ button, select the appropriate drive F: ( CD-ROM Drive) then click
on the ‘OK’ button. 9. Click on the ‘OK’ button, select your monitor model and
click on the ‘Next’ button. 10. Click on ‘Finish’ button then the ‘Close’
button.
34
Windows XP
1. Start Windows® XP 2. Click on the ‘Start’ button and then click on
‘Control Panel’.
3. Select and click on the category `Appearance and Themes’
4. Click on the ‘Display’ Item.
35
5. Select the ‘Settings’ tab then click on the ‘Advanced’ button.
6. Select ‘Monitor’ tab – If the ‘Properties’ button is inactive, it means
your monitor is properly configured. Please stop installation. – If the
‘Properties’ button is active, click on ‘Properties’ button. Please follow the
steps below.
7. Click on the ‘Driver’ tab and then click on ‘Update Driver…’ button.
36
8. Select the ‘Install from a list or specific location [advanced]’ radio
button and then click on the ‘Next’ button.
9. Select the ‘Don’t Search. I will choose the driver to install’ radio
button. Then click on the ‘Next’ button.
10. Click on the ‘Have disk…’ button, then click on the ‘Browse…’ button and
then select the appropriate drive F: (CD-ROM Drive).
11. Click on the ‘Open’ button, then click the ‘OK’ button. 12. Select your
monitor model and click on the ‘Next’ button. – If you can see the ‘has not
passed Windows® Logo testing to verify its compatibility with Windows® XP’
message, please click on the ‘Continue Anyway’ button. 13. Click on the
‘Finish’ button then the ‘Close’ button. 14. Click on the ‘OK’ button and then
the ‘OK’ button again to close the Display Properties dialog box.
37
Windows Vista
1. Click “Start ” and “Control Panel”. Then, double-click on “Appearance and
Personalization”.
2. Click “Personalization” and then “Display Settings”. 3. Click “Advanced
Settings…”.
38
4. Click “Properties” in the “Monitor” tab. If the “Properties” button is
deactivated, it means the configuration for your monitor is completed. The
monitor can be used as is. If the message “Windows needs…” is displayed, as
shown in the figure below, click “Continue”.
5. Click “Update Driver…” in the “Driver” tab.
6. Check the “Browse my computer for driver software” checkbox and click “Let
me pick from a list of device drivers on my computer”.
7. Click on the ‘Have disk…’ button, then click on the ‘Browse…’ button and
then select the appropriate drive F:Driver (CD-ROM Drive). 8. Select your
monitor model and click on the ‘Next’ button. 9. Click “Close” “Close” “OK”
“OK” on the following screens displayed in sequence.
39
Windows 7
1.Start Windows® 7 2.Click on the ‘Start’ button and then click on ‘Control
Panel’.
3. Click on the ‘Display’ icon.
40
4.Ckick on the “Change display settings” button. 5.Click the “Advanced
Settings” button. 6.Click the “Monitor” tab and then click the “Properties”
button.
41
7.Click the “Driver” tab.
8. Open the “Update Driver Software-Generic PnP Monitor” window by clicking
on “Update Driver… “and then click the “Browse my computer for driver
software” button.
9. Select “Let me pick from a list of device drivers on my computer”.
42
10. Click the “Have Disk” button. Click on the “Browse” button and navigate
to the following directory: X:Drivermodule name (where X is the drive letter
designator for the CD-ROM drive).
11. Select the “xxx.inf” file and click the “Open” button. Click the “OK”
button. 12. Select your monitor model and click the “Next” button. The files
will be copied from the CD to your hard disk drive. 13. Close all open windows
and remove the CD. 14. Restart the system. The system will automatically
select the maximum refresh rate and corresponding Color Matching Profiles.
43
Windows 8
1. Start Windows® 8 2. Right click and click All apps at the bottom-right of
the screen.
3. Click on the “Control panel” icon 4. Set the “View by” to “Large icons” or
“Small icons”.
5. Click on the “Display” icon. 44
6. Click on the “Change display settings” button. 7. Click the “Advanced
Settings” button.
8. Click the “Monitor” tab and then click the “Properties” button. 45
9. Click the “Driver” tab.
10. Open the “Update Driver Software-Generic PnP Monitor” window by clicking
on “Update Driver… ” and then click the “Browse my computer for driver
software” button.
11. Select “Let me pick from a list of device drivers on my computer”. 46
12. Click the “Have Disk” button. Click on the “Browse” button and navigate
to the following directory: X:Drivermodule name (where X is the drive letter
designator for the CD-ROM drive).
13. Select the “xxx.inf” file and click the “Open” button. Click the “OK”
button. 14. Select your monitor model and click the “Next” button. The files
will be copied from the CD to your hard disk
drive. 15. Close all open windows and remove the CD. 16. Restart the system.
The system will automatically select the maximum refresh rate and
corresponding Color
Matching Profiles.
47
i-Menu
Welcome to “i-Menu” software by AOC. i-Menu makes it easy to adjust your
monitor display setting by using on screen menus instead of the OSD button on
the monitor. To complete installation, please follow the installation guide.
48
e-Saver
Welcome to use AOC e-Saver monitor power management software! The AOC e-Saver
features Smart Shutdown functions for your monitors, allows your monitor to
timely shutdown when PC unit is at any status (On, Off, Sleep or Screen
Saver); the actual shutdown time depends on your preferences (see example
below). Please click on “driver/e-Saver/setup.exe” to start installing the
e-Saver software, follow the install wizard to complete software installation.
Under each of the four PC status, you may choose from the pull-down menu the
desired time (in minutes) for your monitor to automatically shutdown. The
example above illustrated: 1) The monitor will never shutdown when the PC is
powered on. 2) The monitor will automatically shutdown 5 minutes after the PC
is powered off. 3) The monitor will automatically shutdown 10 minutes after
the PC is in sleep/stand-by mode. 4) The monitor will automatically shutdown
20 minutes after the screen saver appears.
You can click “RESET” to set the e-Saver to its default settings like below.
49
Screen+
Welcome to “Screen+” software by AOC, Screen+ software is a desktop screen
splitting tool, it splits the desktop into different panes, each pane displays
a different window. You only need to drag the window to a corresponding pane,
when you want to access it. It supports multiple monitor display to make your
task easier. Please follow the installation software to install it.
50
Troubleshoot
Problem & Question Power LED Is Not ON
No images on the screen
Possible Solutions
Make sure the power button is ON and the Power Cord is properly connected to a
grounded power outlet and to the monitor.
Is the power cord connected properly? Check the power cord connection and
power supply.
Is the signal cable connected correctly? (Connected using the signal cable)
Check the signal cable connection.
If the power is on, reboot the computer to see the initial screen (the login
screen), which can be seen. If the initial screen (the login screen) appears,
boot the computer in the applicable mode (the safe mode for Windows
ME/XP/2000) and then change the frequency of the video card. (Refer to the
Setting the Optimal Resolution) If the initial screen (the login screen) does
not appear, contact the Service Center or your dealer.
Can you see “Input Not Supported” on the screen? You can see this message when
the signal from the video card exceeds the maximum resolution and frequency
that the monitor can handle properly. Adjust the maximum resolution and
frequency that the monitor can handle properly.
Make sure the AOC Monitor Drivers are installed.
Picture Is Fuzzy & Has Ghosting Shadowing Problem
Adjust the Contrast and Brightness Controls. Press to auto adjust. Make sure you are not using an extension cable or switch box. We recommend plugging the monitor directly to the video card output connector on the back .
Picture Bounces, Flickers Or Wave Pattern Appears In The Picture
Move electrical devices that may cause electrical interference as far away from the monitor as possible. Use the maximum refresh rate your monitor is capable of at the resolution your are using.
51
Monitor Is Stuck In Active Off-Mode”
The Computer Power Switch should be in the ON position. The Computer Video Card should be snugly fitted in its slot. Make sure the monitor’s video cable is properly connected to the computer. Inspect the monitor’s video cable and make sure no pin is bent. Make sure your computer is operational by hitting the CAPS LOCK key on the keyboard while observing the CAPS LOCK LED. The LED should either turn ON or OFF after hitting the CAPS LOCK key.
Missing one of the primary colors (RED, GREEN, or BLUE)
Inspect the monitor’s video cable and make sure that no pin is damaged. Make sure the monitor’s video cable is properly connected to the computer.
Screen image is not centered Adjust H-Position and V-Position or press hot-key
(Power/AUTO).
or sized properly Picture has color defects
Adjust RGB color or select desired color temperature. (white does not look
white)
Horizontal or vertical disturbances on the screen
Use Windows 95/98/2000/ME/XP shut-down mode Adjust CLOCK and FOCUS. Press to auto-adjust.
Display not on whole screen in default resolution ration
Use I-menu software from CD(or download from AOC official website), select “reset” option to adjust.
52
Specification
General Specification
Panel
Product name Driving system Viewable Image Size Pixel pitch Video Separate
Sync. Display Color Dot Clock
Horizontal scan range Horizontal scan Size(Maximum) Vertical scan range
Vertical scan Size(Maximum) Optimal preset resolution Plug & Play
Resolution
Input Connector
Input Video Signal Power Source
Power Consumption
Off timer Speakers
Physical
Connector Type
Characteristics
Signal Cable Type
Temperature:
Environmental Humidity:
Altitude:
E2770SD/E2770SHE/M2770V/I2770V/I2770VHE TFT Color LCD 68.6cm diagonal 0.3114mm(H)X0.3114mm(V) R, G, B Analog lnterface & Digital Interface H/V TTL 16.7M Colors 148.5MHz
30 kHz – 83 kHz 597.89mm 50 Hz – 76 Hz 336.31mm 1920x 1080 @60 Hz VESA DDC2B/CI E2770SD/M2770V/I2770V:D-Sub 15pin; DVI 24pin E2770SHE:D-Sub 15pin;;HDMI I2770VHE: D-Sub 15pin; DVI 24pin; HDMI; Analog: 0.7Vp-p(standard), 75 OHM, TMDS 100-240V~, 50/60Hz E2770SD/I2770V:Active: 30 W (typical) E2770SHE/I2770VHE:Active: 32 W (typical) M2770V:Active: 38 W (typical) Standby 0.5 W 0-24 hrs NA
E2770SD/M2770V/I2770V:D-Sub ; DVI-D E2770SHE:D-Sub ; HDMI I2770VHE: D-Sub ; DVI-D;HDMI; Detachable
Operating Non-Operating Operating Non-Operating Operating Non-Operating
0° to 40° -25°to 55° 10% to 85% (non-condensing) 5% to 93% (non-condensing) 0~ 3658m (0~ 12000 ft ) 0~ 12192m (0~ 40000 ft )
53
Panel Resolution
Product name Driving system Viewable Image Size Pixel pitch Video Separate Sync. Display Color Dot Clock Horizontal scan range Horizontal scan Size(Maximum) Vertical scan range Vertical scan Size(Maximum) Optimal preset resolution Plug & Play Input Connector Input Video Signal Power Source
Power Consumption
Off timer Speakers
Physical
Connector Type
Characteristics Signal Cable Type
Temperature:
Environmental Humidity:
Altitude:
E2770PQU/I2770PQ TFT Color LCD 68.6cm diagonal 0.3114mm(H)X0.3114mm(V) R, G, B Analog lnterface & Digital Interface H/V TTL 16.7M Colors 148.5MHz
30 kHz – 83 kHz 597.89mm 50 Hz – 76 Hz 336.31mm 1920x 1080 @60 Hz VESA DDC2B/CI D-Sub 15pin; DVI 24pin; HDMI(MHL) ;DP Analog: 0.7Vp-p(standard), 75 OHM, TMDS 100-240V~, 50/60Hz E2770PQU:Active32 W(typical) I2770PQ: Active31W(typical) Standby 1W 0-24 hrs 2WX2
15-pin Mini D-Sub DVI-D HDMI DP Detachable
Operating Non-Operating Operating Non-Operating Operating Non-Operating
0° to 40° -25°to 55° 10% to 85% (non-condensing) 5% to 93% (non-condensing) 0~ 3658m (0~ 12000 ft ) 0~ 12192m (0~ 40000 ft )
54
Panel Resolution
Physical Characteristics Environmental
Model name Driving system Viewable Image Size Pixel pitch Video Separate Sync.
Display Color Dot Clock Horizontal scan range Horizontal scan range Horizontal
scan Size(Maximum) Vertical scan range Vertical scan Size(Maximum) Optimal
preset resolution Optimal preset resolution
Plug & Play Input Connector Input Video Signal Power Source Power Consumption
Off timer Speakers Connector Type Signal Cable Type Temperature: Operating
Non-Operating Humidity: Operating Non-Operating Altitude: Operating Non-
Operating
Q2770PQU TFT Color LCD 68.6cm diagonal 0.233mm(H)X0.233mm(V) R, G, B Analog
lnterface & Digital Interface H/V TTL 16.7M Colors 241.5MHz 30 kHz – 83 kHz
for D-Sub 30 kHz – 99 kHz for DVI (dual link) ; HDMI ; DP 596.74mm
50 Hz – 76 Hz 335.66mm 1920x 1080 @60 Hz for D-Sub 2560x 1440 @60 Hz for DVI
(dual link) ; HDMI ; DP only VESA DDC2B/CI D-Sub 15pin; DVI 24pin; HDMI;DP
Analog: 0.7Vp-p(standard), 75 OHM, TMDS 100-240V~, 50/60Hz Active: 45W
(typical) Standby 0.5W 0-24 hrs 2WX2 15-pin Mini D-Sub DVI-D HDMI DP
Detachable
0° to 40° -25° to 55°
10% to 85% (non-condensing) 5% to 93% (non-condensing)
0~ 3658m (0~ 12000 ft ) 0~ 12192m (0~ 40000 ft )
55
Panel Resolution
Model name Driving system Viewable Image Size Pixel pitch Video Separate Sync. Display Color Dot Clock Horizontal scan range Horizontal scan range Horizontal scan Size(Maximum) Vertical scan range Vertical scan range Vertical scan Size(Maximum) Optimal preset resolution Optimal preset resolution Plug & Play Input Connector Input Video Signal Power Source
Power Consumption
Physical Characteristics Environmental
Off timer Speakers Connector Type Signal Cable Type Temperature: Operating Non-Operating Humidity: Operating Non-Operating Altitude: Operating Non- Operating
G2770PQU TFT Color LCD 68.6cm diagonal 0.311mm(H)X0.311mm(V) R, G, B Analog
lnterface & Digital Interface H/V TTL 16.7M Colors 330MHz 30 kHz – 83 kHz 30
kHz – 160 kHz for DVI (dual link) ; DP only 597.6mm 50 Hz – 76 Hz 50Hz~146Hz
for DVI (dual link) ; DP only 336.15mm 1920x 1080 @60 Hz 1920x 1080 @144 Hz
for DVI (dual link) ; DP only VESA DDC2B/CI D-Sub 15pin; DVI 24pin; HDMI;DP
Analog: 0.7Vp-p(standard), 75 OHM, TMDS 100-240V~, 50/60Hz Active: 45W
(typical) Standby 0.5W 0-24 hrs 2WX2 15-pin Mini D-Sub DVI-D HDMI DP
Detachable
0° to 40° -25° to 55°
10% to 85% (non-condensing) 5% to 93% (non-condensing)
0~ 3658m (0~ 12000 ft ) 0~ 12192m (0~ 40000 ft )
56
Panel Resolution
Physical Characteristics Environmental
Model name Driving system Viewable Image Size Pixel pitch Video Separate Sync.
Display Color Dot Clock Horizontal scan range Horizontal scan Size(Maximum)
Vertical scan range Vertical scan Size(Maximum) Optimal preset resolution Plug
& Play Input Connector
Input Video Signal Power Source Power Consumption
Off timer Speakers Connector Type
Signal Cable Type Temperature: Operating Non-Operating Humidity: Operating
Non-Operating Altitude: Operating Non-Operating
M2870V/ M2870VQ/M2870VHE TFT Color LCD 71.1cm diagonal 0.32mm(H)X0.32mm(V) R,
G, B Analog lnterface & Digital Interface H/V TTL 16.7M Colors 148.5MHz 30 kHz
– 83 kHz 620.9mm 50 Hz – 76 Hz 341.2mm 1920x 1080 @60 Hz VESA DDC2B/CI
(M2870V)D-Sub 15pin; DVI 24pin (M2870VHE)D-Sub 15pin; DVI 24pin; HDMI;
(M2870VQ)D-Sub 15pin; DVI 24pin; HDMI;DP Analog: 0.7Vp-p(standard), 75 OHM,
TMDS 100-240V~, 50/60Hz Active: 41W (typical) Standby 0.5 W 0-24 hrs 2WX2
(M2870VQ) M2870V:D-Sub ; DVI-D M2870VHE:D-Sub ; DVI-D,HDMI M2870VQ:D-Sub ;
DVI-D,HDMI;DP Detachable
0° to 40° -25° to 55°
10% to 85% (non-condensing) 5% to 93% (non-condensing)
0~ 3658m (0~ 12000 ft ) 0~ 12192m (0~ 40000 ft )
57
Preset Display Modes
E2770SD/E2770SHE/E2770PQU/M2770V/M2870V/I2770V/I2770VHE/M2870VHE/M2870VQ/I2770PQ
Standard
Resolution
H. Frequency (kHz)
V. Frequency (Hz)
VGA
640 X 480@60Hz
31.469
59.94
MAC
640 X 480@67Hz
35
MODE
66.667
VGA
640 X 480@72Hz
37.861
72.809
VGA
640 X 480@75Hz
37.5
75
IBM MODE
720 X 400@70Hz
31.469
70.087
800 X 600@56Hz
35.156
56.25
SVGA
800 X 600@60Hz 800 X 600@72Hz
37.879 48.077
60.317 72.188
800 X 600@75Hz
46.875
75
MAC MODE
832 X 624@75Hz
49.725
74.551
1024 X 768@60Hz
48.363
60.004
XGA
1024 X 768@70Hz
56.476
70.069
1024 X 768@75Hz
60.023
75.029
1280 X 960@60Hz
60
60
SXGA
1280 X 1024@60Hz 1280 X 1024@75Hz
63.981 79.976
60.02 75.025
1280X 720@60Hz
44.772
59.855
WXGA+
1440 X 900@60Hz
55.935
59.876
WSXGA+
1680 X 1050@60Hz
65.29
59.95
FHD
1920 X 1080@60Hz
67.5
60
58
Q2770PQU Standard VGA
MAC MODE VGA VGA
IBM MODE
SVGA
MAC MODE
XGA
SXGA
WXGA+ WSXGA+
FHD WQHD
Resolution
640 X 480@60Hz 640 X 480@67Hz 640 X 480@72Hz 640 X 480@75Hz 720 X 400@70Hz 800
X 600@56Hz 800 X 600@60Hz 800 X 600@72Hz 800 X 600@75Hz 832 X 624@75Hz 1024 X
768@60Hz 1024 X 768@70Hz 1024 X 768@75Hz 1280 X 960@60Hz 1280 X 1024@60Hz 1280
X 1024@75Hz 1280X 720@60Hz 1440 X 900@60Hz 1680 X 1050@60Hz 1920 X 1080@60Hz
2560 X 1440@60Hz
H. Frequency (kHz)
31.469 35
37.861 37.5
31.469 35.156 37.879 48.077 46.875 49.725 48.363 56.476 60.023
60 63.981 79.976 44.772 55.935 65.29
67.5 88.787
V. Frequency (Hz)
59.94 66.667 72.809
75 70.087 56.25 60.317 72.188
75 74.551 60.004 70.069 75.029
60 60.02 75.025 59.855 59.876 59.95
60 60
WQHD Mode(2560×1440) for Q2770PQU model DVI(dual link), Display Port only; For HDMI, the highest supporting screen resolution is also 2560 x 1440, but it always depends on your capability of graphics card and BluRay/video players.
59
G2770PQU
Standard
VGA
SVGA
XGA SXGA WXGA (DVI/HDMI/DP) WSXGA (DVI/HDMI/DP)
HD *** (DVI/HDMI/DP) IBM MODES DOS MAC MODES VGA MAC MODES SVGA
HD(only DVI/DP)
Resolution
640×480@60Hz 640×480@72Hz 640×480@75Hz 800×600@56Hz 800×600@60Hz 800×600@72Hz
800×600@75Hz 800×600@100Hz 1024×768@60Hz 1024×768@70Hz 1280×1024@60Hz
1440×900@60Hz
1680×1050@60Hz
1920×1080@60Hz
1280×720@60Hz
720×400@70Hz 640×480@67Hz 832×624@75Hz 1920×1080@100Hz 1920×1080@120Hz
1920×1080@144Hz
H. Frequency (kHz)
31.469 37.861
37.5 35.156 37.879 48.077 46.875 46.875 48.363 56.476 63.981
V. Frequency (Hz)
59.94 72.809
75 56.25 60.317 72.188
75 75 60.004 70.069 60.02
55.935
59.887
65.29
67.5
45
31.469 35
49.725 113.3 137.2 158.1
59.954
60
60
70.087 66.667 74.551
100 120 144
HDMI/DP Timing(E2770SHE/E2770PQU/Q2770PQU/G2770PQU /I2770VHE/M2870VQ/M2870VHE)
Format 480P 480P 576P 720P 1080P
Resolution 640 X 480 720 X 480 720 X 576 1280 X 720 1920 X 1080
Vertical frequency 60Hz 60Hz 50Hz
50Hz,60Hz 50Hz,60Hz
MHL Timing(E2770PQU)
Format 480P 480P 576P 720P 1080P
Resolution 640 X 480 720 X 480 720 X 576 1280 X 720 1920 X 1080
Type SD SD SD HD HD
Vertical frequency 60Hz 60Hz 50Hz
50Hz,60Hz 30Hz,50Hz,60Hz
60
Pin Assignments
15-Pin Color Display Signal Cable
Pin No. 1 2 3 4 5 6 7 8
Signal Name Video-Red Video-Green Video-Blue N.C. Detect Cable GND-R GND-G GND-B
Pin No. 9 10 11 12 13 14 15
Signal Name +5V Ground N.C. DDC-Serial data H-sync V-sync DDC-Serial clock
24-Pin Color Display Signal Cable
Pin Number
1 2 3 4 5 6 7 8 9 10 11 12
24-Pin Color Display Signal Cable TMDS data 2 TMDS data 2 TMDS data 2/4 Shield
TMDS data 4 TMDS data 4
DDC Clock DDC Data N.C. TMDS data 1 TMDS data 1 TMDS data 1/3 Shield TMDS data
3
Pin Number
13 14 15 16 17 18 19 20 21 22 23 24
24-Pin Color Display Signal Cable TMDS data 3 5V Power Ground (for+5V) Hot
Plug Detect TMDS data 0 TMDS data 0 TMDS data 0/5 Shield TMDS data 5 TMDS data
5
TMDS Clock Shield TMDS Clock + TMDS Clock
61
19-Pin Color Display Signal Cable
Pin No. Signal Name
Pin No. Signal Name
1
TMDS Data 2+
9
TMDS Data 0
2
TMDS Data 2 Shield
10
TMDS Clock +
3
TMDS Data 2
11
TMDS Clock Shield
4
TMDS Data 1+
12
TMDS Clock
5
TMDS Data 1Shield
13
CEC
6
TMDS Data 1
14
Reserved (N.C. on device
7
TMDS Data 0+
15
SCL
8
TMDS Data 0 Shield
16
SDA
Pin Signal Name No. 17 DDC/CEC Ground 18 +5V Power 19 Hot Plug Detect
20-Pin Color Display Signal Cable
Pin No. 1 2 3 4 5 6 7 8 9 10
Signal Name ML_Lane 3 (n) GND ML_Lane 3 (p) ML_Lane 2 (n) GND ML_Lane 2 (p) ML_Lane 1 (n) GND ML_Lane 1 (p) ML_Lane 0 (n)
Pin No. 11 12 13 14 15 16 17 18 19 20
Signal Name GND ML_Lane 0 (p) CONFIG1 CONFIG2 AUX_CH(p) GND AUX_CH(n) Hot Plug Detect Return DP_PWR DP_PWR
62
Plug and Play
Plug & Play DDC2B Feature This monitor is equipped with VESA DDC2B
capabilities according to the VESA DDC STANDARD. It allows the monitor to
inform the host system of its identity and, depending on the level of DDC
used, communicate additional information about its display capabilities. The
DDC2B is a bi-directional data channel based on the I2C protocol. The host can
request EDID information over the DDC2B channel.
63
Regulation
FCC Notice
FCC Class B Radio Frequency Interference Statement WARNING: (FOR FCC CERTIFIED
MODELS) NOTE: This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy, and if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures: Reorient or relocate
the receiving antenna. Increase the separation between the equipment and
receiver. Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected. Consult the dealer or an experienced
radio/TV technician for help.
NOTICE : The changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate the
equipment. Shielded interface cables and AC power cord, if any, must be used
in order to comply with the emission limits. The manufacturer is not
responsible for any radio or TV interference caused by unauthorized
modification to this equipment. It is the responsibilities of the user to
correct such interference. It is the responsibility of the user to correct
such interference.
64
WEEE DeclarationOptional
Disposal of Waste Equipment by Users in Private Household in the European
Union.
This symbol on the product or on its packaging indicates that this product
must not be disposed of with your other household waste.Instead, it is your
responsibility to dispose of your waste equipment by handing it over to a
designated collection point for the recycling of waste electrical and
electronic equipment.The separate collection and recycling of your waste
equipment at the time of disposal will help to conserve natural resources and
ensure that it is recycled in a manner that protects human health and the
environment. For more information about where you can drop off your waste
equipment for recycling, please contact your local city office, your household
waste disposal service or the shop where you purchased the product .
WEEE Declaration for IndiaOptional
This symbol on the product or on its packaging indicates that this product
must not be disposed of with your other household waste. Instead it is your
responsibility to dispose of your waste equipment by handing it over to a
designated collection point for the recycling of waste electrical and
electronic equipment. The separate collection and recycling of your waste
equipment at the time of disposal will help to conserve natural resources and
ensure that it is recycled in a manner that protects human health and the
environment. For more information about where you can drop off your waste
equipment for recycling in India please visit the below web link.
www.aocindia.com/ewaste.php. This product complies with all implemented RoHS
type regulations worldwide, including but not limited to, EU, Korea, Japan, US
States (e.g. California), Ukraine, Serbia, Turkey, Vietnam and India. We
continue to monitor, influence and develop our processes to comply with
upcoming proposed RoHS type regulations, including but not limited to, Brazil,
Argentina, Canada.
Restriction on Hazardous Substances statement (India)
This product complies with the “India E-waste Rule 2011” and prohibits use of
lead, mercury, hexavalent chromium, polybrominated biphenyls or polybromi-
nated diphenyl ethers in concentrations exceeding 0.1 weight % and 0.01 weight
% for cadmium, except for the exemptions set in Schedule 2 of the Rule.
65
EPA Energy StarOptional
ENERGY STAR® is a U.S. registered mark. As an ENERGY STAR® Partner, AOC
International (Europe) BV and Envision Peripherals, Inc. have determined that
this product meets the ENERGY STAR® guidelines for energy efficiency.
EPEAT DeclarationOptional
EPEAT is a system to help purchasers in the public and private sectors
evaluate, compare and select desktop computers, notebooks and monitors based
on their environmental attributes. EPEAT also provides a clear and consistent
set of performance criteria for the design of products, and provides an
opportunity for manufacturers to secure market recognition for efforts to
reduce the environmental impact of its products.
AOC believes in protecting the environment. With a key concern for the
conservation of natural resources, as well as landfill protection, AOC
announces the launch of AOC monitor’s packaging recycling program. This
program is designed to help you discard of your monitor carton and filler
materials properly. If a local recycling center is not available, AOC will
recycle the packaging material for you, including foam filler and carton. AOC
Display solution will only recycle AOC monitor packaging. Please refer to the
following website address: Only for North and South American, excluding
Brazil: http://us.aoc.com/about/environmental_impact For Germany: http://www
.aoc-europe.com/en/service/tco.php For Brazil:
http://www.aoc.com.br/2007/php/index.php?req=pagina&pgn_id=134
66
TCO DOCUMENT
(FOR TCO CERTIFIED MODELS) 67
Service
Warranty Statement for Europe
LIMITED THREE-YEAR WARRANTY
For AOC LCD Monitors sold within Europe, AOC International (Europe) B.V.
warrants this product to be free from defects in material and workmanship for
a period of Three (3) years after the original date of consumer purchase.
During this period, AOC International (Europe) B.V. will, at its option,
either repair the defective product with new or rebuilt parts, or replace it
with a new or rebuilt product at no charge except as stated below. In the
absent of the proof of purchase, the warranty will start 3 months after the
date of manufacturing indicated on the product.
If the product appears to be defective, please contact your local dealer or
refer to the service and support section on www.aoc-europe.com for the
warranty instructions in your country. The freight cost for the warranty is
pre-paid by AOC for the delivery and return. Please ensure you provide a dated
proof of purchase along with the product and deliver to the AOC Certified or
Authorized Service Center under the following condition:
Make sure the LCD Monitor is packed in a proper carton box (AOC prefers the
original carton box to protects your monitor well enough during transport).
Put the RMA number on the address label Put the RMA number on the shipping
carton
AOC International (Europe) B.V. will pay the return shipping charges within
one of the countries specified within this warranty statement. AOC
International (Europe) B.V. is not responsible for any costs associated with
the transportation of product across international borders. This includes the
international border within the European Union. If the LCD Monitor is not
available for collection when the currier attends, you will be charged a
collection fee.
- This limited warranty does not cover any losses or damages that occur as a result of:
Damages during transport due to improper packaging Improper installation or maintenance other then in accordance with AOC’s user manual Misuse Neglect Any cause other than ordinary commercial or industrial application Adjustment by non-authorized source Repair, modification, or installation of options or parts by anyone other than an AOC Certified or
Authorized Service Center Improper environments like humidity, water damage and dusts Damaged by violence, earthquake and terrorist attacks Excessive or inadequate heating or air conditioning or electrical powers failures, surges, or other
irregularities
This limited warranty does not cover any of the product firmware or hardware that you or any third party have modified or altered; you bear the sole responsibility and liability for any such modifications or alteration.
68
All AOC LCD Monitors are produced according to the ISO 9241-307 Class 1 pixel
policy standards. If your warranty has expired, you still have access to all
available service options, but you will be responsible for the cost of
service, including parts, labor, shipping (if any) and applicable taxes. AOC
Certified or Authorized Service Center will provide you with an estimate of
service costs before receiving your authorization to perform service. ALL
EXPRESS AND IMPLIED WARRANTIES FOR THIS PRODUCT (INCLUDING THE WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE) ARE LIMITED IN DURATION
TO A PERIOD OF THREE (3) YEARS FOR PARTS AND LABOR FROM THE ORIGINAL DATE OF
CONSUMER PURCHASE. NO WARRANTIES (EITHER EXPRESSED OR IMPLIED) APPLY AFTER
THIS PERIOD. AOC INTERNATIONAL (EUROPE) B.V. OBLIGATIONS AND YOUR REMEDIES
HEREUNDER ARE SOLELY AND EXCULSIVELY AS STATED HERE. AOC INTERNATIONAL
(EUROPE) B.V. LIABILITY, WHETHER BASED ON CONTRACT, TORT, WARRANTY, STRICT
LIABILITY, OR OTHER THEORY, SHALL NOT EXCEED THE PRICE OF THE INDIVIDUAL UNIT
WHOSE DEFECT OR DAMAGE IS THE BASIS OF THE CLAIM. IN NO EVENT SHALL AOC
INTERNATIONAL (EUROPE) B.V. BE LIABLE FOR ANY LOSS OF PROFITS, LOSS OF USE OR
FACILITIES OR EQUIPMENT, OR OTHER INDIRECT, INCIDENTAL, OR CONSEQUENTIAL
DAMAGE. SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR
CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION MAY NOT APPLY TO YOU. ALTHOUGH
THIS LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, YOU MAY HAVE OTHER
RIGHTS, WHICH MAY VARY FROM COUNTRY TO COUNTRY. THIS LIMITED WARRANTY IS ONLY
VALID FOR PRODUCTS PURCHASED IN THE MEMBER COUNTRIES OF THE EUROPEAN UNION.
Information in this document is subject to change without notice. For more
information, please visit: http://www.aoc-europe.com
69
Warranty Statement for Middle East and Africa (MEA)
And
The Commonwealth of Independent States (CIS)
LIMITED ONE to THREE YEARS WARRANTY
For AOC LCD Monitors sold within the Middle East and Africa (MEA) and the
Commonwealth of Independent States (CIS), AOC International (Europe) B.V.
warrants this product to be free from defects in material and workmanship for
a period of One (1) to Three (3) years from the manufacture date depending on
sale country. During this period, AOC International (Europe) B.V. offers a
Carry-In (return to Service Center) Warranty Support at an AOC’s Authorized
Service Center or Dealer and at its option, either repair the defective
product with new or rebuilt parts, or replace it with a new or rebuilt product
at no charge except as stated below. As a Standard Policy, the warranty will
be calculated from the manufacture date identified from the product ID serial
number, but the total warranty will be Fifteen (15) months to Thirty Nine (39)
months from MFD (manufacture date) depending on sale country. Warranty will be
considered for exceptional cases that are out of warranty as per the product
ID serial number and for such exceptional cases; Original Invoice/Proof Of
Purchase Receipt is mandatory.
If the product appears to be defective, please contact your AOC authorized
dealer or refer to the service and support section on AOC’s website for the
warranty instructions in your country:
Egypt: http://aocmonitorap.com/egypt_eng CIS Central Asia:
http://aocmonitorap.com/ciscentral Middle East:
http://aocmonitorap.com/middleeast South Africa:
http://aocmonitorap.com/southafrica Saudi Arabia:
http://aocmonitorap.com/saudiarabia
Please ensure you provide a dated proof of purchase along with the product and
deliver to the AOC Authorized Service Center or Dealer under the following
condition:
Make sure the LCD Monitor is packed in a proper carton box (AOC prefers the
original carton box to protects your monitor well enough during transport).
Put the RMA number on the address label Put the RMA number on the shipping
carton
- This limited warranty does not cover any losses or damages that occur as a result of:
Damages during transport due to improper packaging Improper installation or maintenance other then in accordance with AOC’s user manual Misuse Neglect Any cause other than ordinary commercial or industrial application Adjustment by non-authorized source
70
Repair, modification, or installation of options or parts by anyone other than
an AOC Certified or Authorized Service Center
Improper environments like humidity, water damage and dusts Damaged by
violence, earthquakes and terrorist attacks Excessive or inadequate heating or
air conditioning or electrical powers failures, surges, or other
irregularities This limited warranty does not cover any of the product
firmware or hardware that you or any third party have modified or altered; you
bear the sole responsibility and liability for any such modifications or
alteration.
All AOC LCD Monitors are produced according to the ISO 9241-307 Class 1 pixel
policy standards.
If your warranty has expired, you still have access to all available service
options, but you will be responsible for the cost of service, including parts,
labor, shipping (if any) and applicable taxes. AOC Certified, Authorized
Service Center or dealer will provide you with an estimate of service costs
before receiving your authorization to perform service.
ALL EXPRESS AND IMPLIED WARRANTIES FOR THIS PRODUCT (INCLUDING THE WARRANTIES
OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE) ARE LIMITED IN
DURATION TO A PERIOD OF ONE (1) to THREE (3) YEARS FOR PARTS AND LABOR FROM
THE ORIGINAL DATE OF CONSUMER PURCHASE. NO WARRANTIES (EITHER EXPRESSED OR
IMPLIED) APPLY AFTER THIS PERIOD. AOC INTERNATIONAL (EUROPE) B.V. OBLIGATIONS
AND YOUR REMEDIES HEREUNDER ARE SOLELY AND EXCULSIVELY AS STATED HERE. AOC
INTERNATIONAL (EUROPE) B.V. LIABILITY, WHETHER BASED ON CONTRACT, TORT,
WARRANTY, STRICT LIABILITY, OR OTHER THEORY, SHALL NOT EXCEED THE PRICE OF THE
INDIVIDUAL UNIT WHOSE DEFECT OR DAMAGE IS THE BASIS OF THE CLAIM. IN NO EVENT
SHALL AOC INTERNATIONAL (EUROPE) B.V. BE LIABLE FOR ANY LOSS OF PROFITS, LOSS
OF USE OR FACILITIES OR EQUIPMENT, OR OTHER INDIRECT, INCIDENTAL, OR
CONSEQUENTIAL DAMAGE. SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF
INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION MAY NOT APPLY TO
YOU. ALTHOUGH THIS LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, YOU MAY
HAVE OTHER RIGHTS, WHICH MAY VARY FROM COUNTRY TO COUNTRY. THIS LIMITED
WARRANTY IS ONLY VALID FOR PRODUCTS PURCHASED IN THE MEMBER COUNTRIES OF THE
EUROPEAN UNION.
Information in this document is subject to change without notice. For more
information, please visit: http://www.aocmonitorap.com
71
AOC Pixel Policy ISO 9241-307 Class 1
72
Warranty Statement for North & South America (excluding Brazil)
WARRANTY STATEMENT for AOC Color Monitors Including those Sold within North
America as Specified
Envision Peripherals, Inc. warrants this product to be free from defects in
material and workmanship for a period of three (3) years for parts & labor and
one (1) year for CRT Tube or LCD Panel after the original date of consumer
purchase. During this period, EPI ( EPI is the abbreviation of Envision
Peripherals, Inc. ) will, at its option, either repair the defective product
with new or rebuilt parts, or replace it with a new or rebuilt product at no
charge except as *stated below. The parts or product that are replaced become
the property of EPI.
In the USA to obtain service under this limited warranty, call EPI for the
name of the Authorized Service Center closest to your area. Deliver the
product freight pre-paid, along with the dated proof of purchase, to the EPI
Authorized Service Center. If you cannot deliver the product in person:
Pack it in its original shipping container (or equivalent) Put the RMA number
on the address label Put the RMA number on the shipping carton Insure it (or
assume the risk of loss/damage during shipment) Pay all shipping charges
EPI is not responsible for damage to inbound product that was not properly
packaged. EPI will pay the return shipment charges within one of the countries
specified within this warranty statement. EPI is not responsible for any costs
associated with the transportation of product across international borders.
This includes the international borders of the countries within this warranty
statements.
In the United States and Canada contact your Dealer or EPI Customer Service,
RMA Department at the toll free number
888-662-9888. Or you can request an RMA
Number online at www.aoc.com/na-warranty.
- This limited warranty does not cover any losses or damages that occur as a result of:
Shipping or improper installation or maintenance Misuse Neglect Any cause other than ordinary commercial or industrial application Adjustment by non- authorized source Repair, modification, or installation of options or parts by anyone other than an EPI Authorized Service Center Improper environment Excessive or inadequate heating or air conditioning or electrical power failures, surges, or other irregularities
This three-year limited warranty does not cover any of the product’s firmware or hardware that you or any third party have modified or altered; you bear the sole responsibility and liability for any such modification or alteration.
73
ALL EXPRESS AND IMPLIED WARRANTIES FOR THIS PRODUCT (INCLUDING THE WARRANTIES
OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE) ARE LIMITED IN
DURATION TO A PERIOD OF THREE (3) YEARS FOR PARTS AND LABOR AND ONE (1) YEAR
FOR CRT TUBE OR LCD PANEL FROM THE ORIGINAL DATE OF CONSUMER PURCHASE. NO
WARRANTIES (EITHER EXPRESSED OR IMPLIED) APPLY AFTER THIS PERIOD. IN THE
UNITED STATES OF AMERICA, SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN
IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATIONS MAY NOT APPLY TO YOU.
EPI OBLIGATIONS AND YOUR REMEDIES HEREUNDER ARE SOLELY AND EXCLUSIVELY AS
STATED HERE. EPI’ LIABILITY, WHETHER BASED ON CONTRACT, TORT. WARRANTY, STRICT
LIABILITY, OR OTHER THEORY, SHALL NOT EXCEED THE PRICE OF THE INDIVIDUAL UNIT
WHOSE DEFECT OR DAMAGE IS THE BASIS OF THE CLAIM. IN NO EVENT SHALL ENVISION
PERIPHERALS, INC. BE LIABLE FOR ANY LOSS OF PROFITS, LOSS OF USE OR FACILITIES
OR EQUIPMENT OR OTHER INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGE. IN THE
UNITED STATES OF AMERICA, SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION
OF INCIDENTAL OR CONSEQUENTIAL DAMAGES. SO THE ABOVE LIMITATION MAY NOT APPLY
TO YOU. ALTHOUGH THIS LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS. YOU
MAY HAVE OTHER RIGHTS WHICH MAY VARY FROM STATE TO STATE.
In the United States of America, this limited warranty is only valid for
Products purchased in the Continental United States, Alaska, and Hawaii.
Outside the United States of America, this limited warranty is only valid for
Products purchased in Canada.
Information in this document is subject to change without notice. For more
details, please visit:
USA: http://us.aoc.com/support/warranty ARGENTINA:
http://ar.aoc.com/support/warranty BOLIVIA: http://bo.aoc.com/support/warranty
CHILE: http://cl.aoc.com/support/warranty COLOMBIA: http://co.aoc.com/warranty
COSTA RICA: http://cr.aoc.com/support/warranty DOMINICAN REPUBLIC:
http://do.aoc.com/support/warranty ECUADOR: http://ec.aoc.com/support/warranty
EL SALVADOR: http://sv.aoc.com/support/warranty GUATEMALA:
http://gt.aoc.com/support/warranty HONDURAS:
http://hn.aoc.com/support/warranty NICARAGUA:
http://ni.aoc.com/support/warranty PANAMA: http://pa.aoc.com/support/warranty
PARAGUAY: http://py.aoc.com/support/warranty PERU:
http://pe.aoc.com/support/warranty URUGUAY: http://pe.aoc.com/warranty
VENEZUELA: http://ve.aoc.com/support/warranty IF COUNTRY NOT LISTED:
http://latin.aoc.com/warranty
74
References
- Homepage | AOC Monitors
- Homepage | AOC Monitors
- Homepage | AOC Monitors
- MHL® – Expand Your World
- Manual-Hub.com – Free PDF manuals!
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>