APEX LD 1919 Digital 19 Inch E320582 60HZ LCD TV Instruction Manual
- June 17, 2024
- Apex
Table of Contents
OPERATING INSTRUCTIONS
MODEL：LD 1919
Please read this manual before connection and use
Introduction
Thank you for choosing this product. This manual will guide you for proper
operation. Before operating the TV, please read this manual properly. Please
do keep this manual in a safe place for future references. This portable TV
has been designed for private use only.
Safety notice items
Preparation
For ventilation, leave a space of at least 10cm free all around the set. To
prevent any fault and unsafe situations, please do not place any objects on
top of the set. Use this apparatus in moderate climates.
Please read the following recommended safety precautions carefully for your
safety.
1. Power Source
The TV set should be operated only from a 120 V AC, 60Hz outlet. Ensure that
you select the correct voltage setting for your convenience.
2. Power Cord
Do not place the TV where the power cord is subject to wear or abuse, pinch, bend or twist the cord excessively. The cord lines may be bared and cut, and cause a short-circuit, resulting in a fire or an electric shock. Do not convert or damage the power cord. Do not allow anything to rest on or roll over the power cord. Do not move the TV with the power cord plugged in. Keep the power cord away from heat sources. Be sure to grasp the plug when disconnecting the power cord.
3. Moisture and Water
Do not use this equipment in a humid and damp place (avoid the bathroom, the sink in the kitchen, and near the washing machine). Do not expose this equipment to rain or water, as this may be dangerous and do not place objects filled with liquids, such as flower vases, on top. Avoid from dripping or splashing. If any solid object or liquid falls into the cabinet, unplug the TV and have it checked by qualified personnel before operating it any further.
4. Cleaning
Before cleaning, unplug the TV set from the wall outlet. Do not use liquid or aerosol cleaners. Use soft and dry cloth.
5. Ventilation
The slots and openings on the TV set are intended for ventilation and to
ensure reliable operation. To prevent overheating, these openings must not be
blocked or covered in anyway.
6. Heat and Flames
The set should not be placed near to naked flames and sources of intense heat,
such as an electric heater. Ensure that no naked flame sources, such as
lighted candles, are placed on top of the TV.
Batteries shall not be exposed to excessive heat such as sunshine, fire or the
like.
7. Lightning
In case of storm and lightning or when going on holiday, disconnect the power cord from the wall outlet.
8. Replacement Parts
When replacement parts are required, be sure the service technician has used
replacement parts which are specified by the manufacturer or have the same
specifications as the original one. Unauthorized substitutions may result in
fire, electrical shock, or other hazards.
9. Servicing
**** Please refer all servicing to qualified personnel. Do not remove the cover yourself as this may result in an electric shock.
10. Waste Disposal
Instructions for waste disposal:
- Packaging and packaging aids are recyclable and should principally be recycled. Packaging materials, such as foil bag, must be kept away from children.
- Battery, including those which are heavy metal-free, should not be disposed of with household waste. Please dispose of used battery in an environmentally sound manner. Find out about the legal regulations which apply in your area.
- Cold cathode fluorescent lamp in LCD PANEL contains a small amount of mercury; please follow local ordinates or regulations for disposal.
Information for users applicable in European Union countries
**** This symbol on the product or on its packaging means that your
electrical and electronic equipment should be disposed at the end of life
separately from your household wastes. There are separate collection systems
for recycling in EU.
For more information, please contact the local authority or the dealer where
you purchased the product.
11. Disconnect Device
The mains plug is used to disconnect TV set from the mains and therefore it
shall remain readily operable.
12. To prevent injury, this device must be securely attached to the wall in
accordance with the installation instructions when mounted to the wall (if the
option is available).
Operating Safety Instructions
When displaying the same still picture for more than 2 hours without any
interruption, the picture contours of the continuously displayed contents may
remain visible on screen, i.e. a persistent image remains. The same applies,
when displaying for more than 2 hours:
- the same background/wallpaper
- logos, video games, computer images, Teletext
- contents with a non-filling aspect ratio (e.g. 4:3 format)
Note:
This device is not suitable for a long-time display of still pictures,
including logos, video games, computer games, Teletext and screen non-filling
contents. Any persistent images caused by displaying still pictures, logos,
video games, computer images, Teletext and screen non-filling contents cannot
be erased. These do not represent any malfunction and will not be covered by
the manufacturer’s warranty.”
PE Connection to mains
Be sure to ground the connection properly. Connect the ground terminal of TV
with the ground terminal provided at the power outlet using the enclosed power
cord. If the provided plug does not fit your outlet, consult an electrician
for replacement of the obsolete outlet.
Accessories
- User’s Manual / Warranty
- Batteries
- Remote control
- Power cord
Product Overview
Control Panel Overview
(1) Control Panel Functions:
- INPUT – To select the input signal: TV/VIDEO/S-VIDEO/YPbPr/PC/HDMI
- MENU – Enter into MENU
- CH+ – TV channel up
- CH- – TV channel down
- VOL+ – Volume up / Right orientation
- VOL- – Volume down / Left orientation
- POWER – Power supply switch
Indicator Light Status
The indicator light is red when the TV is in standby mode. The indicator light
is green when you press the‘ ‘ Key
(2) Illustration of Connectors
Connectors descriptions:
1. Power On/Off button
2： Power receptacle AC120V 60Hz
3： Antenna input, connect antenna connector or aerial interface here to
receive cable / aerial signal
4： Earphone output
5, 6: L/R audio inputs (AV) from exterior AV devices such as DVD players,
Video Camera’s etc.
7： Composite video input, connect video input from external device here
8： S-VIDEO input, connect video input from external device here
9： Y Pb Pr input interface
10: DB15 VGA interface, connect power supply adaptor here
11： PC sound card audio inputs
12: HDMI input interface
Remote Control Overview
1- Illustration of the keys on the remote control:
| 1. DISPLAY | Screen Display ON/OFF |
|---|---|
| 2. FAV | Favorite channel |
| 3. INPUT | Select TV / VIDEO / S-VIDEO / YPbPr / PC / HDMI |
| 4. GUIDE | Display digital program information |
| 5. ZOOM | Switch to different display mode |
| 6. CH + / CH- | Change TV channels |
| 7. ▲ ▼ | Control the on-screen menu up/down cursor |
| 8. ◀ ▶ | Control the on-screen menu left/right cursor |
| 9. MENU | Display on-screen menu |
| 10. ENTER | Press to confirm |
| 11.SLEEP | Press to set sleep timer |
| 12. EXIT | Exit menu |
| 13. CH.LIST | Channel list |
| 14. MUTE | Turn the sound on or off. |
| 15. POWER | Press to set TV ON/OFF standby mode |
| 16. 0-9 | Press to select TV channel number |
| 17. – | Digital channel substation selector |
| 18. RECALL | Last channel viewed |
| 19. VOL+ / VOL- | Adjusts the volume up/down |
| 20. CCD | Press to select closed caption |
| 21. MTS | Press to select a second audio channel (if available) |
| 22. PICTURE | Press to adjust picture mode |
| 23. AUDIO | Press to adjust audio mode |
Connecting Input Signals to TV
A) Connect with TV signal
Connection steps：
- Power your LCD TV off.
- Connect an antenna cable (CATV) to the corresponding interface connector (75 Ω ANT) on the back of the LCD-TV. Connect the other end of the antenna cable to the antenna connector on the wall or on your digital cable / satellite receiver. Now you are able to view regular cable TV.
- Turn on the power of the LCD-TV.
- Press the INPUT button to set the video input mode of the LCD-TV to “TV” mode. The channel number appears in the top right side of the screen.
- You can use key CH+ / CH- button or the number keys on the remote control to select the channel you want to watch.
B) Connect to external AV devices using Composite and S-Video inputs
Connection steps：
- Read the user guide supplied with your AV devices and ensure that it has Composite or S-Video connectors;
- Power your LCD TV and your AV device off.
- Connect a Composite video cable (not supplied) to the yellow composite video connector input on the back of the LCD-TV. Now insert the other end of the composite cable into the yellow composite connector output on the AV device.
- Alternatively connect a S-Video Cable (not supplied, provide better image quality) to the S-Video connector on the back of the LCD-TV. Now insert the other end of the S-Video cable into the S-Video connector on the AV device.
- Connect the RCA audio cables (not supplied, white and red connectors) from the AV devices’ RCA audio output connectors to the RCA audio input connectors on the back of the LCD-TV.
- Connect an antenna cable (CATV) to the corresponding interface connector (75 Ω ANT) on the back of the LCD-TV. Connect the other end of the antenna cable to the antenna output connector on the VCR or DVD recorder. Now you are able to view and record a TV signal at the same time.
- Turn on the power of the LCD-TV first, and then turn on the power of the AV device.
- Press the INPUT button to set the video input mode of the LCD-TV to “S-VIDEO” mode or “VIDEO” mode.
C) Connect with YPbPr signal
Connection steps：
- Read the user guide supplied with your AV devices and ensure that it has a “YPbPr” connector;
- Power your LCD TV off.
- Connect a YPbPr cable to the corresponding interface connector on the back of the LCD-TV.
- Turn on the power of the LCD-TV.
- Press the INPUT button to set the video input mode of the LCD-TV to “YPbPr” mode.
- Format: 480i, 480p, 720p, 1080i.
D) Connect with HDMI signal
Connection steps：
- Read the user guide supplied with your AV devices and ensure that it has a “HDMI” connector;
- Power your LCD TV off.
- Connect a HDMI cable to the corresponding interface connector on the back of the LCD-TV.
- Turn on the power of the LCD-TV.
- Press the INPUT button to set the video input mode of the LCD-TV to “HDMI” mode.
- Format: 480i, 480p, 720p, 1080i
E) Connect with PC signal
- Connect a D-sub cable between PC IN connector on the TV and Video Output connector on your PC
- Connect an audio cable between the PC IN (Audio) jack on the TV and the audio out jack on our PC
- Press the INPUT button on the remote control to select PC mode.
PC INPUT SIGNAL REFERENCE CHART
| Resolution | Frequency |
|---|
800 x 600
1024 x 768
1280 x 768
1360 x 768
1440 x 900| 60Hz
60Hz
60Hz
60Hz
60Hz
Frequency may vary based on PC signal.
TV Operation
(1) Basic operation
Initial Setup Menu
NOTE: If this is the first time you turn on the LCD TV, the Initial Setup
Menu will display.
Menu Language
Select the preferred language when viewing on screen menus. Use the ENTER/► to
select language.
Tuning Band
Select Tuning Band mode. Press ENTER/► button to select Air/Cable STD/Cable
HRC/Cable IRC/Cable Auto.
Auto Channel Search
When using your LCD TV for the first time. Please scan for all available
broadcasting channels in your local area. Press ENTER/► button to enter the
Auto Channel Search Program.
NOTE: Auto Channel Search for TV channels in your local area may take
several minutes to complete.
Choosing a TV channel
-
Press CH+/CH- button on the side panel or on the remote control.
Press CH+ button for the next channel
Press CH – button for the previous channel. -
Press 0-9 buttons and button.
You can select the channel by pressing 0 to 9 buttons and button directly for the channel you want.
Example:
To select 1-Analog channel (e.g. Channel 5): Press the 5, then press and 0
button.
To select 2- Analog channel (e.g. Channel 20): Press the 2 and 0 buttons ,
then press and 0 button.
To select 3- Analog channel (e.g. Channel 103): Press the 1 and 0 and 3
button, then press and 0 button.
To select a channel number for digital channel (e.g. Channel 2-1): Press the 2
button, then press and 1 button, then press ENTER button.
Note: After select the digit button, the digit will be memorized.
Volume Control
- Press VOL+/-button to adjust the volume
- Press MUTE button to mute the TV, Press MUTE button again or VOL+/- button to cancel the mute function. The On Screen Display (OSD) may display different screen settings based on the input signal of use.
On Screen Display Adjustment
– Press MENU button to display the main menu.
– Press◄/►/▲/▼buttons to select/adjust the each setting.
Selecting input source
You can select the input source by pressing INPUT button on the remote control
or on the front panel.
PICTURE menu options
- Press MENU button on the side panel or the remote control to display the main menu.
- Press ▲/▼ button to select the PICTURE menu, then press ► button for the submenu.
- Press ▲/▼ button to select the item you want to adjust.
- Press ENTER/► button repeatedly to adjust the value.
- When you are satisfied with your choice, press ◄ button to go to the previous menu, or press MENU/EXIT button to exit.
Picture Mode
Select Picture Mode in PICTURE menu accordingly to your viewing requirement.
(Available picture mode: Standard, Vivid, Bright, User.)
You should set the Picture Mode to “User” first if you want to change the
value of Contrast / Brightness / Sharpness /Color
TIPS: you can select the picture mode directly by pressing PICTURE button
repeatedly.
Contrast
Press ▼ / ▲ button to select this item, then press ENTER/► button to adjust
the contrast of the picture.
Brightness
Press ▼ / ▲ button to select this item, then press ENTER/► button to adjust
the brightness of the picture.
Sharpness
Press ▼ / ▲ button to select this item, then press ENTER/► button to adjust
the sharpness of the picture.
Color
Press ▼ / ▲ button to select this item, then press ENTER/► button to adjust
the color saturation of the picture.
Tint
Press ▼ / ▲ button to select this item, then press ENTER/► button to adjust
the tint of the picture.
NOTE: The Tint item is not available but in NTSC color system.
Aspect Ratio
Press ▼ / ▲ button to select this item, then press ENTER/► button to adjust
the aspect the aspect ratio of the picture. (Available aspect ratio: Full
Screen, Normal, Zoom, Wide, Cinema, Waterglass, Fullscreen)
AUD I O menu op t i ons
- Press MENU button on the side panel or the remote control to display the main menu.
- Press ▲/▼ button to select the AUDIO menu, then press ► button for the submenu.
- Press ▲/▼ button to select the item you want to adjust.
- Press ENTER/► button repeatedly to adjust the value.
- When you are satisfied with your choice, press ◄ button to go to the previous menu, or press MENU/EXIT button to exit.
Audio Language
Press ▼ / ▲ button to select this item, then press ENTER/► button to adjust
the aspect the audio language.
NOTE: The Language selection may not be available if the programs system
does not include the language code. You may select the language mode directly
by pressing MTS button on the remote control.
Audio Mode
Select Audio Mode in AUDIO menu. (Available audio mode:
Voice/Concert/Jazz/User) You should set the Audio Mode to “User” first if you
want to change the value of Bass/Treble.
TIPS: you can select the Audio mode directly by pressing AUDIO button
repeatedly. Audio mode must be set to “User” in order to change
“Base/Tremble/Balance”
Bass
Press ▼ / ▲ button to select this item, then press ENTER/► button to adjust
the bass value.
Treble
Press ▼ / ▲ button to select this item, then press ENTER/► button to adjust
the Treble value
Balance
Press ▼ / ▲ button to select this item, then press ENTER/► button to adjust
the sound balance.
Setup menu options
- Press MENU button on the side panel or the remote control to display the main menu.
- Press ▲/▼ button to select the SETUP menu, then press ► button for the submenu.
- Press ▲/▼ button to select the item you want to adjust.
- Press ENTER/► button repeatedly to adjust the value.
- When you are satisfied with your choice, press ◄ button to go to the previous menu, or press MENU/EXIT button to exit.
Tuning Band
Select Tuning Band mode. (Available tuning band mode: Air, Cable STD, Cable
HRC, Cable IRC, Cable Auto.)
Signal Level
In DTV mode, you can refer the strength of the current channel, and you can
tune manually and adjust the angle, orientation of the antenna.
Auto Channel Search
Press ▼ / ▲ button to select this item, then press ENTER/► button to scan
available channels in your area. The channels found are automatically saved
into the channel list.
Add On Channel Search
Press ▼ / ▲ button to select this item, then press ENTER/► button to enter the
Add On Channel Search Program. This function will add additional channels to
channel list previously not found.
Manual Channel Set
- Press ENTER button to display a channel list that you can select channel as below:
- Press ► button to label each channel “Viewable” or “Not Viewable”
Channel labels
Allows you to name the channel selected. Press ◄/► button to select the
position of letter, press ▲/▼button to set the name.
Menu Language
Press ▼ / ▲ button to select this item, then press ENTER/► button to select
the On Screen Display (OSD) language. (Available Language: English, Spanish,
and French) Reset Press ENTER/► button to reset all items to the default
value.
Feature menu options
- Press MENU button on the side panel or the remote control to display the main menu.
- Press ▲/▼ button to select the FEATURE menu, then press ► button for the submenu.
- Press ▲/▼ button to select the item you want to adjust.
- Press ENTER/► button repeatedly to adjust the value.
- When you are satisfied with your choice, press ◄ button to go to the previous menu, or press MENU/EXIT button to exit.
Time Set
Press ▼ / ▲ button to select this item, then press ENTER/► button to enter
Time Set Menu.
Time Set Mode
Press ENTER/► button to select the time set mode from Auto and Manual.
Please set the Time Set Mode to “Manual” first if you want to change the value
of Time Zone/Year/Date/Time.
Time Zone
Press ▼ / ▲ button to select this item, then press ENTER/► button to select
the time zone.
Sleep Timer
Select the sleep timer to automatically turn off TV by setting the amount of
time desired.
Advanced Video Menu
Press ▼ / ▲ button to select this item, then press ENTER/► button for Advanced
Video Menu.
Noise Reduction
Press ENTER/◄/► button to select the level of noise reduction from
Off/Low/Medium/High.
Color Temperature
Press ENTER/◄/► button to select the color temperature from Cool/Normal/Warm.
3D/YC
Press ENTER/◄/► button to set the 3D/YC On or Off.
Adaptive Contrast
Press ENTER/◄/► button to set the Adaptive Contrast On or Off.
Gradient Enable
Press ENTER/◄/► button to set the Gradient Enable On or Off.
Blue Screen
Press ENTER/◄/► button to set the Blue Screen On or Off.
Audio Only
Press ENTER and select “OK” to hide the video. Press and hold the power button
for 3 seconds to restore to factory default settings.
Parental Control
Please enter a password to set Parental Control. The factory default password
is 0000
Password Set
Please enter the correct old password before setting a new password, and after
setting the new password, you need to enter it again to confirm it.
Master Lock
Press ENTER/► button to set the Master Lock On/Off. If you set this function
on, all the parental control lock will be unavailable and it can play all
kinds of programs.
Unrated Lock
Press ENTER/► button to set the Unrated Lock On/Off. If you set this function
on, all the programs will be locked even they are unrated programs.
US Ratings
Press ▼ / ▲ button to select this item, then press ENTER/► button for US
Ratings Menu. Canadian Rating Menu Press ▼ / ▲ button to select this item,
then press ENTER/► button for Canadian Rating Menu.
Advanced Rating
Press ▼ / ▲ button to select this item, then press ENTER/► button to set
advanced rating on/off.
Closed Caption
Press ▼ / ▲ button to select this item, then press ENTER/► button for Closed
Caption Menu.
CC Mode
Press ENTER/► button to select CC Mode from CC Off / CC On / CC ON Mute.
Analog CC
Press ENTER/► button to select Analog CC Mode.
Digital CC
Press ENTER/► button to select Digital CC Mode.
Advanced CC Settings
Press ENTER/► button for Advance CC Settings Menu.
Style: Press ENTER/► button to select CC Style between Automatic and Custom,
you need to set it to Custom first if you want to change the value of items
below.
Size: Normal/Large/Small.
Font: Default/Font1 to Font7.
Text Color: Red/Green/Blue/Yellow/Magenta/Cyan/Black/White.
Text Opacity: Solid/Flashing/Transparent/Translucent.
Background Color: Black/White/Red/Green/Blue/Yellow/Magenta/Cyan.
Background Opacity: Solid/Flashing/Transparent/Translucent.
Edge Effect: None/Raised/Depressed/Uniform/Left Shadow/Right Shadow.
Edge Color: Black/White/Red/Green/Blue/Yellow/Magenta/Cyan.
Feature menu options in PC Mode
Press Input button to select the input source to PC Mode.
PC Set
Press ▼ / ▲ button to select PC Set, then press ENTER/► button for PC Setting
Menu.
H-Position
Press ENTER/► button to adjust the horizontal position of the picture.
V-Position
Press ENTER/► button to adjust the vertical position of the picture
Clock
Press ENTER/► button to adjust the clock rate of the picture.
Phase
Press ENTER/► button to adjust the phase of the picture.
Auto Adjust
Press ENTER/► button to auto adjust the PC setting.
Setting
Press ENTER/► button to reset the PC setting to factory default.
Feature menu options in YPbPr
Press INPUT button to select the input source to YPbPr.
YPbPr Set
Press ▼ / ▲ button to select YPbPr Set, then press ENTER/► button for YPbPr
Setting Menu.
H-Position
Press ENTER/► button to adjust the horizontal position of the picture.
V-Position
Press ENTER/► button to adjust the vertical position of the picture
Clock
This function is unavailable in component mode.
Phase
Press ENTER/► button to adjust the phase of the picture.
Auto Adjust
This function is unavailable in component mode.
Setting
Press ENTER/► button to reset the YPbPr Setting to factory default.
Technical Specifications
| TV-SYSTEM | ATV system | NTSC-M |
|---|---|---|
| DTV system | 8VSB/QAM | |
| Max. Storage Channel | 800CH | |
| RECEIVING CHANNEL | Air, Cable STD, Cable HRC, Cable IRC | |
| PROGRAM CHANNES | Air 2-69, Cable 1-135* | |
| OPERATING VOLTAGE | 120V AC, 60Hz | |
| AUDIO | Stereo | |
| AUDIO OUTPUT POWER (%10 THD) | 2 x 3W | |
| OSD Languages | English, French, Spanish | |
| POWER CONSUMPTION(W) | 60 W standby< 3W | |
| PANEL | 16:10 wide screen, 19-inch screen | |
| SIZE (mm) | WIDE | 19.3″ Inch ,49 cm |
| HEIGHT | 15.9″ Inch ,40.4 cm | |
| DEPTH | 9.8″ Inch ,24.9cm | |
| WEIGHT (LB) | 15.4 Ibs, 7Kg |
*Cable channels may vary depending on your cable provider.
NOTE: Apex Digital Inc. reserves the right to modify the specifications shown without prior notice.
Limited North American Warranty
Apex Digital Inc.
LD1919
Apex Digital, Inc. expresses the following limited warranty. This warranty
extends to new APEX LD1919 purchased from an authorized Apex U.S.
reseller/retailer and used within the U.S. by the original purchaser or
consumer received the new product as a gift and no other purchaser or
transferee. You must retain the original bill of sale for proof of purchase.
Limited One (1) Year Warranty
Apex Digital warrants the parts in this product against defects in material or
workmanship for a period of one (1) year from the date of original purchase.
During this period, Apex Digital will replace a defective part with a new or
refurbished part without charge to you. It is the responsibility of the
consumer to retain original packaging or provide like packaging in order to
facilitate the warranty process. Apex Digital, Inc. will incur no liability
whatsoever to provide packaging for warranty items. Upon receipt of the
warranty item, should it be determined that the packaging was insufficient,
Apex Digital Inc., at its discretion, may void the warranty. The consumer is
responsible for the transportation (cost) and insurance charges (if
applicable) for the set to the Service Center or Apex Digital. The consumer
will be responsible for all tariffs, duty and taxes imposed to ship or receive
warranty or warranty replacement units to and from the U.S. You must receive a
return authorization number before sending a unit in for service.
Limited Ninety (90) Days Labor Warranty
Apex Digital warrants it will be responsible for labor charges for repair or
replacement of parts on this product for a period of ninety days from the date
of original retail purchase. During this period, Apex Digital will repair or
replace a defective part at its sole option, with a new or refurbished part or
product without charge to you, except for the shipping charges incurred by the
consumer, if any, to the Service Center.
Your Responsibility
The above warranties are subject to the following conditions: You must retain
the original bill of sales to provide proof of purchase.
There are no exceptions. You must call the provided phone number for an
assessment of the problem. No service or shipment of product will be accepted
unless an RMA# is provided, attached or printed to shipping carton along with
bill of sale. You are responsible for all tariffs and taxes imposed to ship or
receive warranty or warranty replacement units to and from the U.S. These
warranties are effective only if product is purchased through an Authorized
retail reseller and the unit is operated in North America. Labor service
charges for set installation, setup, adjustment of consumer controls and
installation or repair of any type of antenna or cable systems are not covered
by this warranty. Reception problems caused by inadequate antenna or cable
systems are your responsibility. Warranties extend only to defects in
materials or workmanship as limited above and do not extend to any other
products or parts that have been lost, discarded or damaged by misuse,
accident, neglect, acts of God, such as lightning or voltage surges in the
home, improper installation, improper maintenance or use in violation of
instructions provided or product which has been modified, have had the serial
number removed, altered, or rendered illegible. Warranties do not cover
cosmetic damage or lost accessories.
How to Obtain Warranty Service
If after following the operating instructions, the Troubleshooting Guide and
the FAQ pages on televisions, found at our website,
www.apexdigitalinc.com. 1. Should it be
necessary to contact Customer Service Center directly, call
800-880-1227 Monday through
Friday, 8am to 6pm (Pacific Time). You will be instructed on how your claim
will be processed. 2. Have your pertinent information available including
proof of purchase and an understanding of the complaint.
Limitations
Your LCD panel is an innovative device that is manufactured to precise
tolerances with active performing pixels of at least 99.99%. As such, it is
NOT a malfunction to view multiple non-performing pixels on your screen. All
warranties implied by state law are expressly limited to the duration of the
limited warranties set forth above with the exception of warranties implied by
state law as herby limited, the foregoing warranty is exclusive and in lieu of
all other warranties, guarantees, agreements etc., with respect to repair or
replacement of any parts. Apex Digital shall not be liable for consequential
or incidental damage.
The warranty gives you specific rights and you may also have these rights that may vary from state to state. Some states do not allow limitation on how long a warranty lasts, or the exclusions or limitation of incidental or consequential damages, so the above may not apply to you.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>