APEX WAVES ISC-1782 2 MP 1.58 GHz Processor Monochrome-Color Smart Camera User Manual

: October 30, 2023
: APEX WAVES

APEX WAVES ISC-1782 2 MP 1.58 GHz Processor Monochrome-Color Smart Camera

APEX-WAVES-ISC-1782-2-MP-1-58-GHz-Processor-Monochrome-Color-Smart-Camera-
PRODUCT

Product Information

The ISC-1782 is an intelligent camera with a 2 MP image sensor and a 1.58 GHz dual-core Intel Celeron N2807 processor. It comes in both monochrome and color variants. The camera has a physical size of 91mm x 54mm x 75mm (length x height x width) without the lens cover and 118mm x 54mm x 75mm with the lens cover. The camera weighs 460g and has a C-mount lens mount.
The camera has three types of connectors – Network (8-pin female X-coded M12), VGA/USB (12-pin male M12), and Power and Digital I/O (12-pin female M12). It requires a 24 VDC power source to operate and has a power consumption of rated current. The camera has a system RAM capacity of 2 GB DDR3L SDRAM and a non-volatile storage capacity of 32 GB. It supports NI Linux Real-Time 64-bit and Windows 10 Enterprise 2016 LTSB 64-bit operating systems.
The camera has an image sensor with a resolution of 2 MP and a pixel size of 4.8 µm x 4.8 µm for the monochrome variant and 2.4 µm x 2.4 µm for the color variant. It has a maximum frame rate of 60 fps for the monochrome variant and 30 fps for the color variant. The camera has IP67 conformity and comes with an IP lens cover that must be screwed firmly into place to maintain harmony.

Product Usage Instructions

Observe all instructions and cautions in the user documentation to prevent camera damage and maintain built-in safety protection.
To maintain IP67 conformity, all unused connectors on the ISC-1782 must be capped and the IP lens cover must be screwed firmly into place.
The camera can only be powered using a 24 VDC power source. Use a power source that meets the rated current requirements of the camera.
To clean the camera, wipe it with a dry towel.

SPECIFICATIONS

These specifications apply to the monochrome and color ISC-1782.
Caution Observe all instructions and cautions in the user documentation. Using the ISC-1782 in a manner not specified can damage the model and compromise the built-in safety protection. Return damaged models to NI for repair.

Definitions

Warranted specifications describe the performance of a model under stated operating conditions and are covered by the model warranty.
Characteristics describe values that are relevant to the use of the model under stated operating conditions but are not covered by the model warranty.
Typical specifications describe the expected performance met by a majority of the models.
Nominal specifications describe parameters and attributes that may be useful in operation. Specifications are Typical unless otherwise noted.

Conditions

Specifications are valid at 23 °C unless otherwise noted.
To maintain IP67 conformity, all unused connectors on the ISC-1782 must be capped and the IP lens cover must be screwed firmly into place.

Physical Characteristics

Power Requirements

APEX-WAVES-ISC-1782-2-MP-1-58-GHz-Processor-
Monochrome-Color-Smart-Camera-FIG-3

Processor

Memory

System RAM
Capacity 2 GB
Type DDR3L SDRAM
Nonvolatile storage
Capacity 32 GB

Operating System

Supported Operating Systems NI Linux Real-Time 64-bit
Windows 10 Enterprise 2016 LTSB 64-bit

Network Port

Speed 100/1000 Mbps
Standard IEEE 802.3 Ethernet, 100Base-TX, and 1000Base-T

Digital Inputs

APEX-WAVES-ISC-1782-2-MP-1-58-GHz-Processor-Monochrome-
Color-Smart-Camera-FIG-6

Digital Outputs

Analog Output

Type 0 to 10 V analog control output signal for lighting control (non- isolated), referenced to system power common (< 1 mA)

Image Sensor

APEX-WAVES-ISC-1782-2-MP-1-58-GHz-Processor-Monochrome-
Color-Smart-Camera-FIG-9

Environmental

APEX-WAVES-ISC-1782-2-MP-1-58-GHz-Processor-Monochrome-
Color-Smart-Camera-FIG-10

Safety

This product is designed to meet the requirements of the following electrical equipment safety standards for measurement, control, and laboratory use:
IEC 61010-1, EN 61010-1
UL 61010-1, CSA C22.2 No. 61010-1
Note For UL and other safety certifications, refer to the product label or the Online Product Certification section.

Electromagnetic Compatibility

This product meets the requirements of the following EMC standards for electrical equipment for measurement, control, and laboratory use:
EN 61326-1 (IEC 61326-1): Class A emissions; Industrial immunity
EN 55011 (CISPR 11): Group 1, Class A emissions
EN 55022 (CISPR 22): Class A emissions
EN 55024 (CISPR 24): Immunity
AS/NZS CISPR 11 : Group 1, Class A emissions
AS/NZS CISPR 22: Class A emissions
FCC 47 CFR Part 15B: Class A emissions
ICES-001: Class A emissions
Note In the United States (per FCC 47 CFR), Class A equipment is intended for use in commercial, light-industrial, and heavy-industrial locations. In Europe,
Canada, Australia and New Zealand (per CISPR 11) Class A equipment is intended for use only in heavy-industrial locations.
Note Group 1 equipment (per CISPR 11) is any industrial, scientific, or medical equipment that does not intentionally generate radio frequency energy for the treatment of material or inspection/analysis purposes.
Note For EMC declarations and certifications, and additional information, refer to the Online Product Certification section.

CE Compliance

This product meets the essential requirements of applicable European Directives, as follows:
2014/35/EU; Low-Voltage Directive (safety)
2014/30/EU; Electromagnetic Compatibility Directive (EMC)
2011/65/EU; Restriction of Hazardous Substances (RoHS)

Online Product Certification

Refer to the product Declaration of Conformity (DoC) for additional regulatory compliance information. To obtain product certifications and the DoC for this product, visit ni.com/certification, search by model number or product line, and click the appropriate link in the Certification column.

Environmental Management

NI is committed to designing and manufacturing products in an environmentally responsible manner. NI recognizes that eliminating certain hazardous substances from our products is beneficial to the environment and to NI customers.
For additional environmental information, refer to the Minimize Our Environmental Impact web page at ni.com/environment. This page contains the environmental regulations and directives with which NI complies, as well as other environmental information not included in this document.

Waste Electrical and Electronic Equipment (WEEE)

EU Customers At the end of the product life cycle, all NI products must be disposed of according to local laws and regulations. For more information about how to recycle NI products in your region, visit ni.com/environment/weee.

Where to Go Next

The following documents and resources contain information you may find helpful as you use the ISC-1782 in an application. Refer to the National Instruments Product Manuals Library at ni.com/manuals for the most recent versions of product documentation.
ISC-178x Getting Started Guide—Explains how to install and configure the software necessary to use the ISC-178x, and how to get started using the hardware.
Power and I/O Accessory for ISC-178x Smart Cameras User Manual—Contains installation and operation instructions for the Power and I/O Accessory for ISC-178x Smart Cameras.
ISC-178x User Manual—Contains detailed electrical and mechanical information about the ISC-178x.

Worldwide Support and Services

The NI website is your complete resource for technical support. At ni.com/support, you have access to everything from troubleshooting and application development self-help resources to email and phone assistance from NI Application Engineers.
Visit ni.com/services for NI Factory Installation Services, repairs, extended warranty, and other services.
Visit ni.com/register to register your NI product. Product registration facilitates technical support and ensures that you receive important information updates from NI.
A Declaration of Conformity (DoC) is our claim of compliance with the Council of the European Communities using the manufacturer’s declaration of conformity. This system protects the user from electromagnetic compatibility (EMC) and product safety. You can obtain the DoC for your product by visiting ni.com/certification. If your product supports calibration, you can obtain the calibration certificate for your product at ni.com/calibration. NI corporate headquarters is located at 11500 North Mopac Expressway, Austin, Texas, 78759-3504. NI also has offices located around the world. For telephone support in the United States, create your service request at ni.com/support or dial 1 866 ASK MYNI (275 6964). For telephone support outside the United States, visit the Worldwide Offices section of ni.com/global to access the branch office websites, which provide up-to-date contact information, support phone numbers, email addresses, and current events.
Information is subject to change without notice. Refer to the NI Trademarks and Logo Guidelines at ni.com/trademarks for information on NI trademarks. Other product and company names mentioned herein are trademarks or trade names of their respective companies. For patents covering NI products/technology, refer to the appropriate location: Help» Patents in your software, the patents.txt file on your media, or the National Instruments Patent Notice at ni.com/patents. You can find information about end-user license agreements (EULAs) and third-party legal notices in the readme file for your NI product. Refer to the Export Compliance Information at ni.com/legal/export-compliance for the NI global trade compliance policy and how to obtain relevant HTS codes, ECCNs, and other import/export data. NI MAKES NO EXPRESS OR IMPLIED WARRANTIES AS
TO THE ACCURACY OF THE INFORMATION CONTAINED HEREIN AND SHALL NOT BE LIABLE FOR ANY ERRORS. U.S.
Government Customers: The data contained in this manual was developed at private expense and is subject to the applicable limited rights and restricted data rights as set forth in FAR 52.227-14, DFAR 252.227-7014, and DFAR 252.227-7015.
© 2017 National Instruments. All rights reserved.

COMPREHENSIVE SERVICES
We offer competitive repair and calibration services, as well as easily accessible documentation and free downloadable resources.

SELL YOUR SURPLUS
We buy new, used, decommissioned, and surplus parts from every NI series
We work out the best solution to suit your individual needs.

Sell For Cash
Get Credit
Receive a Trade-In Deal

OBSOLETE NI HARDWARE IS IN STOCK & READY TO SHIP
We stock New, New Surplus, Refurbished, and Reconditioned NI Hardware.

Request a Quote CLICK HEREISC-1782

Bridging the gap between the manufacturer and your legacy test system.
All trademarks, brands, and brand names are the property of their respective owners
1-800-915-6216
www.apexwaves.com
sales@apexwaves.com

Documents / Resources

| APEX WAVES ISC-1782 2 MP 1.58 GHz Processor Monochrome-Color Smart Camera [pdf] User Manual
ISC-1782 2 MP 1.58 GHz Processor Monochrome-Color Smart Camera, ISC-1782, 2 MP 1.58 GHz Processor Monochrome-Color Smart Camera, Processor Monochrome-Color Smart Camera, Monochrome-Color Smart Camera, Smart Camera, Camera
---|---