AOC E2770SD LCD Monitor User Manual

AOC E2770SD LCD Monitor

Specifications

• Model Numbers: E2770SD, E2770SD6, E2770SHE, E2770PQU, E2770SH, Q2770PQU, G2770PQU, G2770PF, M2770V, M2870V, M2870VHE, M2870VQ, I2770V, I2770VHE, I2770PQ
• Backlight: LED

Product Usage Instructions

Power

The monitor should be operated only from the type of power source indicated on the label. If you are not sure of the type of power supplied to your home, consult your dealer or local power company.

The monitor is equipped with a three-pronged grounded plug, a plug with a third (grounding) pin. This plug will fit only into a grounded power outlet as a safety feature. If your outlet does not accommodate the three-wire plug, have an electrician install the correct outlet, or use an adapter to ground the appliance safely. Do not defeat the safety purpose of the grounded plug.

Unplug the unit during a lightning storm or when it will not be used for long periods of time. This will protect the monitor from damage due to power surges.

Do not overload power strips and extension cords. Overloading can result in fire or electric shock. The wall socket shall be installed near the equipment and shall be easily accessible.

Installation

Do not place the monitor on an unstable cart, stand, tripod, bracket, or table. If the monitor falls, it can injure a person and cause serious damage to this product. Use only a cart, stand, tripod, bracket, or table recommended by the manufacturer or sold with this product. Follow the manufacturer’s instructions when installing the product and use mounting accessories recommended by the manufacturer. A product and cart combination should be moved with care.

Never push any object into the slot on the monitor cabinet. It could damage circuit parts causing a fire or electric shock. Never spill liquids on the monitor.

Do not place the front of the product on the floor. If you mount the monitor on a wall or shelf, use a mounting kit approved by the manufacturer and follow the kit instructions. Leave some space around the monitor as shown below. Otherwise, air-circulation may be inadequate hence overheating may cause a fire or damage to the monitor.

Recommended Ventilation Areas

When the monitor is installed on the wall or on the stand, ensure proper ventilation by leaving space around the monitor as follows:

• Left Side: Minimum 10 cm
• Right Side: Minimum 10 cm
• Top: Minimum 10 cm
• Bottom: Minimum 10 cm

FAQs

• Q: Where should I plug in the monitor?
  • A: The monitor should be plugged into a grounded power outlet as indicated on the label. If your outlet does not accommodate the three-wire plug, use an adapter to ground the appliance safely.
• Q: Can I leave the monitor plugged in during a lightning storm?
  • A: It is recommended to unplug the monitor during a lightning storm or when it will not be used for long periods of time to protect it from damage due to power surges.
• Q: How much space should I leave around the monitor when installing it on a wall or shelf?
  • A: It is recommended to leave a minimum of 10 cm of space on the left side, right side, top, and bottom of the monitor to ensure proper ventilation and prevent overheating.

E2770SD/E2770SD6/E2770SHE/E2770PQU/E2770SH Q2770PQU G2770PQU/G2770PF M2770V/M2870V/M2870VHE/M2870VQ I2770V/I2770VHE/I2770PQ
(LED Backlight)

Safety

National Conventions
The following subsections describe notational conventions used in this document. Notes, Cautions, and Warnings Throughout this guide, blocks of text may be accompanied by an icon and printed in bold type or in italic type. These blocks are notes, cautions, and warnings, and they are used as follows: NOTE: A NOTE indicates important information that helps you make better use of your computer system. CAUTION: A CAUTION indicates either potential damage to hardware or loss of data and tells you how to avoid the problem. WARNING: A WARNING indicates the potential for bodily harm and tells you how to avoid the problem. Some warnings may appear in alternate formats and may be unaccompanied by an icon. In such cases, the specific presentation of the warning is mandated by regulatory authority.
4
r

Power
The monitor should be operated only from the type of power source indicated on the label. If you are not sure of the type of power supplied to your home, consult your dealer or local power company.
The monitor is equipped with a three-pronged grounded plug, a plug with a third (grounding) pin. This plug will fit only into a grounded power outlet as a safety feature. If your outlet does not accommodate the three-wire plug, have an electrician install the correct outlet, or use an adapter to ground the appliance safely. Do not defeat the safety purpose of the grounded plug.
Unplug the unit during a lightning storm or when it will not be used for long periods of time. This will protect the monitor from damage due to power surges.
Do not overload power strips and extension cords. Overloading can result in fire or electric shock. The wall socket shall be installed near the equipment and shall be easily accessible.
5
r

Installation
Do not place the monitor on an unstable cart, stand, tripod, bracket, or table. If the monitor falls, it can injure a person and cause serious damage to this product. Use only a cart, stand, tripod, bracket, or table recommended by the manufacturer or sold with this product. Follow the manufacturer’s instructions when installing the product and use mounting accessories recommended by the manufacturer. A product and cart combination should be moved with care.
Never push any object into the slot on the monitor cabinet. It could damage circuit parts causing a fire or electric shock. Never spill liquids on the monitor.
Do not place the front of the product on the floor. If you mount the monitor on a wall or shelf, use a mounting kit approved by the manufacturer and follow the kit instructions. Leave some space around the monitor as shown below. Otherwise, air-circulation may be inadequate hence overheating may cause a fire or damage to the monitor. See below the recommended ventilation areas around the monitor when the monitor is installed on the wall or on the stand:
6
r

Cleaning
Clean the cabinet regularly with cloth. You can use soft-detergent to wipe out the stain, instead of strong-detergent which will cauterize the product cabinet.
When cleaning, make sure no detergent is leaked into the product. The cleaning cloth should not be too rough as it will scratch the screen surface.
Please disconnect the power cord before cleaning the product.
7
r

Other
If the product is emitting a strange smell, sound or smoke, disconnect the power plug IMMEDIATELY and contact a Service Center.
Make sure that the ventilating openings are not blocked by a table or curtain. Do not engage the LCD monitor in severe vibration or high impact conditions during operation. Do not knock or drop the monitor during operation or transportation. For display with glossy bezel the user should consider the placement of the display as the bezel may cause disturbing reflections from surrounding light and bright surfaces.
8
r

Setup
Content of the Box

Monitor

CD Manual Monitor Base /Stand

Wire holder

MHL cable

Power Cable DVI Cable Analog Cable HDMI Cable USB Cable Audio Cable DP Cable
Not all signal cables (Analog , Audio, DVI, USB, DP, MHLand HDMI cables) will be provided for all countries and regions. Please check with the local dealer or AOC branch office for confirmation.

9
r

Setup Stand
Please setup or remove the Stand following the steps as below. 70S/70V Setup
Remove:
70P Setup:
Remove:
10
r

Adjusting Viewing Angle
For optimal viewing it is recommended to look at the full face of the monitor, then adjust the monitor’s angle to your own preference. Hold the stand so you will not topple the monitor when you change the monitor’s angle. You are able to adjust the monitor’s angle from -5° to 25 °.
NOTE:Do not adjust the viewing angle over 25 degrees in order to avoid damage. NOTE:
Do not touch the LCD screen when you change the angle. It may cause damage or break the LCD screen. Do not put your hand close to the gap between the monitor and the base to avoid the injury when adjusting the viewing angle.
11
r

Connecting the Monitor
Cable Connections In Back of Monitor and Computer: 1. E2770SD/ E2770SD6/M2770V/M2870V/I2770V
2. E2770SHE
12
r

3 .E2770PQU

4 .Q2770PQU/G2770PQU

5. M2870VHE / I2770VHE/E2770SH
6. M2870VQ
7. I2770PQ

13
r

8.G2770PF
1. Power 2. Analog (D-Sub 15-Pin VGA cable) 3. DVI 4. HDMI 5. Audio in 6. Earphone out 7. Display port 8. HDMI/MHL 9. USB input 10. USB 2.0×2 11. USB 3.0 12. USB 3.0+ fast charging 13. AC power switch
To protect equipment, always turn off the PC and LCD monitor before connecting. 1. Connect the power cable to the AC port on the back of the monitor. 2. Connect one end of the 15-pin D-Sub cable to the back of the monitor and connect the other end to the
computer’s D-Sub port. 3. (Optional ­Requires a video card with DVI port)Connect one end of the DVI cable to the back of the monitor
and connect the other end to the computer’s DVI port. 4. (Optional ­ Requires a video card with HDMI port) – Connect one end of the HDMI cable to the back of the
monitor and connect the other end to the computer’s HDMI port. 5. (Optional ­ Requires a video card with DP port) – Connect one end of the DP cable to the back of the monitor
and connect the other end to the computer’s DP port. 6. (Optional ­ Requires a video card with MHL port) – Connect one end of the MHL cable to the back of the
monitor and connect the other end to the computer’s MHL port. 7. (Optional)Connect the audio cable to audio in port on the back of the monitor 8. Turn on your monitor and computer. If your monitor displays an image, installation is complete. If it does not display an image, please refer Troubleshooting.
14
r

System requirement: refer to G2770PF
FreeSync function: 1. FreeSync function is working with DisplayPort. 2.Compatible Graphics Card: Recommend list is as the below, also could be checked by visiting www.AMD.com · AMD Radeon R9 295X2 · AMD Radeon R9 290X · AMD Radeon R9 290 · AMD Radeon R9 285 · AMD Radeon R7 260X · AMD Radeon R7 260
Wall Mounting
Preparing to Install An Optional Wall Mounting Arm. 70S/70V
70P
This monitor can be attached to a wall mounting arm you purchase separately. Disconnect power before this procedure. Follow these steps: 1. Remove the base. 2. Follow the manufacturer’s instructions to assemble the wall mounting arm. 3. Place the wall mounting arm onto the back of the monitor. Line up the holes of the arm with the holes in the
back of the monitor. 15
r

4. Insert the 4 screws into the holes and tighten. 5. Reconnect the cables. Refer to the user’s manual that came with the optional wall mounting arm for
   instructions on attaching it to the wall. Noted : VESA mounting screw holes are not available for all models, please check with the dealer or official department of AOC.
   16
   r

AOC Anti-Blue Light Feature DescriptionOptional
Studies have shown that just as ultra-violet rays can cause eye damage, blue light rays from LED displays can cause damage to different parts of the eye and affect vision over time. AOC Anti-Blue Light feature uses a smart technology to reduce the harmful blue light waves without affecting the color or image of the display.
17
r

Adjusting
Setting Optimal Resolution
Windows Vista
For Windows Vista: 1 Click START. 2 Click CONTROL PANEL.
3 Click Appearance and Personalization.
4 Click Personalization
18
r

5 Click Display Settings. 6 Set the resolution SLIDE-BAR to Optimal preset resolution
19
r

Windows XP
For Windows XP: 1 Click START.
2 Click SETTINGS. 3 Click CONTROL PANEL. 4 Click Appearance and Themes.
5 Double click DISPLAY.
20
r

6 Click SETTINGS. 7 Set the resolution SLIDE-BAR to Optimal preset resolution
Windows ME/2000
For Windows ME/2000: 1 Click START. 2 Click SETTINGS. 3 Click CONTROL PANEL. 4 Double click DISPLAY. 5 Click SETTINGS. 6 Set the resolution SLIDE-BAR to Optimal preset resolution
21
r

Windows 8
For Windows 8: 1. Right click and click All apps at the bottom-right of the screen.
2. Set the “View by” to “Category”. 3. Click Appearance and Personalization.
22
r

4. Click DISPLAY. 5. Set the resolution SLIDE-BAR to Optimal preset resolution.
   23
   r

Hotkeys

E2770SD/M2770V/M2870V/I2770V/E2770SD6

1

Source/Auto/Exit

2

Clear Vision/-

3

4:3 or Wide/+

4

Menu/Enter

5

Power

E2770SHE/E2770PQU/Q2770PQU/G2770PQU/M2870VQ/M2870VHE/I2770VHE/I2770PQ/E2770SH

1

Source/Auto/Exit

2

Clear Vision/-

3

Volume/+

4

Menu/Enter

5

Power

G2770PF

1

Source/Auto/Exit

2

Game Mode/-

3

Volume /+

4

Menu/Enter

5

Power

24
r

Clear Vision 1. When there is no OSD, Press the “-” button to activate Clear Vision. 2. Use the “-” or “+” buttons to select between weak, medium, strong, or off settings. Default setting is always
“off”.
3. Press and hold “-” button for 5 seconds to activate the Clear Vision Demo, and a message of “Clear Vision Demo: on” will be display on the screen for a duration of 5 seconds. Press Menu or Exit button, the message will disappear. Press and hold “-” button for 5 seconds again, Clear Vision Demo will be off.
Clear Vision function provides the best image viewing experience by converting low resolution and blurry images into clear and vivid images.
25
r

Using “MHL(Mobile High-Definition Link)”Optional
1.”MHL” (Mobile High-Definition Link) This feature allows you to enjoy videos and photos (imported from a connected mobile device that supports MHL) on the screenof the product. To use the MHL function, you need an MHL-certified mobile device. You can check if your mobile device is
MHL certified on the device manufacturer’s website. To find a list of MHL- certified devices, visit the official MHL website (http://www.mhlconsortium.org). To use the MHL function, the latest version of software must be installed on the mobile device. On some mobile devices, the MHL function may not be available depending on the device’s performance or functionality. Since the display size of the product is larger than those of mobile devices, the picture quality may degrade. This product is officially MHL-certified. If you encounter any problem when using the MHL function, please contact the manufacturer of the mobile device. The picture quality may degrade when content (imported from the mobile device) with a low Resolution is played on the product.
Using “MHL” 1. Connect the micro USB port on the mobile device to the [HDMI / MHL] port on the product using the MHL
cable.
When the MHL cable is used, [HDMI / MHL] is the only port on this monitor that supports the MHL function. Mobile device must be purchased separately. 2. Press the source button and switch to HDMI /MHL to activate MHL mode. 3. After about 3 seconds, the MHL screen will be displayed if MHL mode is active. Remark: The indicated time “3 sec later” may vary depending on the mobile device.
When the mobile device is not connected or does not support MHL
If MHL mode is not activated, check the connection of the mobile device. If MHL mode is not activated, check if the mobile device supports MHL. If MHL mode is not activated even though the mobile device supports MHL, update the firmware of the mobile
device to the latest version. If MHL mode is not activated even though the mobile device supports MHL, check if mobile device MHL port
is MHL standard port otherwise an additional MHL-enabled adapter is required.
26
r

OSD Setting

Basic and simple instruction on the control keys.
1. Press the MENU-button to activate the OSD window. 2. Press – or + to navigate through the functions. Once the desired function is highlighted, press the
MENU-button to activate. Press – or + to navigate through the sub-menu. Once the desired function is highlighted, press MENU-button to activate. 3. Press – or + to change the settings of the selected function. Press AUTO to exit. If you want to adjust any other function, repeat steps 2-3. 4. OSD Lock Function: To lock the OSD, press and hold the MENU-button while the monitor is off and then press power-button to turn the monitor on. To un-lock the OSD, press and hold the MENU-button while the monitor is off and then press power-button to turn the monitor on. Notes: 1. If the product has only one signal input, the item of “Input Select” is disabled. 2. If the product screen size is 4:3 or input signal resolution is wide format, the item of “Image Ratio” is disabled. 3. One of Clear vision, DCR, Color Boost, and Picture Boost functions is activated; the other three functions are turned off accordingly.
27
r

Luminance

1 Press

(Menu) to display menu.

2 Press – or + to select

(Luminance), and press

to enter.

3 Press – or + to select submenu, and press 4 Press – or + to adjust.

to enter.

5 Press

to exit.

Brightness Contrast

0-100 0-100
Standard

Text

Eco mode

Internet Game

Movie

Gamma DCR Overdrive

Sports
Gamma1 Gamma2 Gamma3 Off
On
Weak Light(only for G2770PF) Medium Strong
Off

Backlight Adjustment. Contrast from Digital-register. Standard Mode.
Text Mode.
Internet Mode.
Game Mode.
Movie Mode.
Sports Mode. Adjust to Gamma 1. Adjust to Gamma 2. Adjust to Gamma 3. Disable dynamic contrast ratio. Enable dynamic contrast ratio. Adjust the response time (only for E2770PQU/Q2770PQU/G2770PQU/I27 70VHE/M2870VHE/M2870VQ/I2770PQ /G2770PF/E2770SH)

28

r

FPS
RTS Game mode Racing
Gamer 1 Gamer 2 off

Shadow Control

0-100

For playing FPS(first Person Shppters) games.Improves dark theme black level details. For playing RTS(Real Time Strategy, improve respnse time and brightness for presenting smooth pictures. For playing Racing games,Provides fastest response time and high color saturation. User’s preference settings saved as Gamer 1. User’s preference settings saved as Gamer 2. No optimization by Smartimage game Shadow Control Default is 50, then end-user can adjust from 50 to 100 or 0 to increase contrast for clear picture. 1. If picture is too dark to be saw the detail clearly, adjusting from 50 to 100 for clear picture. 2. If picture is too white to be saw the detail clearly, adjusting from 50 to 0 for clear picture

29
r

Image Setup

1 Press

(Menu) to display menu.

2 Press – or + to select

(Image Setup), and press

3 Press – or + to select submenu, and press

4 Press – or + to adjust.

5 Press

to exit.

to enter.

to enter.

Clock Phase Sharpness H.Position V.Position

0-100 0-100 0-100 0-100 0-100

Adjust picture Clock to reduce Vertical-Line noise. Adjust Picture Phase to reduce Horizontal-Line noise. Adjust picture sharpness. Adjust the horizontal position of the picture. Adjust the vertical position of the picture.

30
r

Color Setup

1 Press

(Menu) to display menu.

2 Press – or + to select

(Color Setup), and press

3 Press – or + to select submenu, and press

4 Press – or + to adjust.

5 Press

to exit.

to enter.

to enter.

Color Temp.
DCB Mode DCB Demo

Warm Normal Cool sRGB
User
Full Enhance Nature Skin Green Field Sky-blue AutoDetect

Red Green Blue on or off on or off on or off on or off on or off on or off

Recall Warm Color Temperature from EEPROM. Recall Normal Color Temperature from EEPROM. Recall Cool Color Temperature from EEPROM. Recall SRGB Color Temperature from EEPROM. Red Gain from Digital-register. Green Gain Digital- register. Blue Gain from Digital-register. Disable or Enable Full Enhance Mode. Disable or Enable Nature Skin Mode. Disable or Enable Green Field Mode. Disable or Enable Sky-blue Mode. Disable or Enable AutoDetect Mode. Disable or Enable Demo.

31
r

Picture Boost

1 Press

(Menu) to display menu.

2 Press – or + to select

(Picture Boost), and press

3 Press – or + to select submenu, and press

4 Press – or + to adjust.

5 Press

to exit.

to enter.

to enter.

Frame Size Brightness Contrast H. position V. position Bright Frame

14-100 0-100 0-100 0-100 0-100 on or off

Adjust Frame Size. Adjust Frame Brightness. Adjust Frame Contrast. Adjust Frame horizontal position. Adjust Frame vertical position. Disable or Enable Bright Frame.

32
r

OSD Setup

1 Press

(Menu) to display menu.

2 Press – or + to select

(OSD Setup), and press

to enter.

3 Press – or + to select submenu, and press 4 Press – or + to adjust.

5 Press

to exit.

to enter.

1. Position V. Position Timeout Transparence Language

0-100 0-100 5-120 0-100

Break Reminder

on or off

DP Capaciliby

1.1/1.2

Adjust the horizontal position of OSD. Adjust the vertical position of OSD. Adjust the OSD Timeout. Adjust the transparence of OSD. Select the OSD language. Disable or Enable (1 hour of work, break ?) / (2 hours of work, break ?) 1.In DP 1.1 mode ,DP-out outputs full image which is from DP-in if DP-in received image data. 2. In DP 1.2 mode. (A) DP-out outputs full image which is from DP-in if DP graphic card outputs single monitor data. (B) DP-out outputs next 1or 2 monitor image(s) if DP graphic card outputs 2 or 3 monitor image by daisy chain.

33
r

Extra

1 Press

(Menu) to display menu.

2 Press – or + to select

(Extra), and press

3 Press – or + to select submenu, and press 4 Press – or + to adjust.

5 Press

to exit.

to enter. to enter.

Input Select Input Select Input Select Input Select Input Select Auto Config Off timer
Image Ratio
DDC-CI Reset Information

Auto / D-SUB / DVI / HDMI/MHL Select input signal source.

/DP

(E2770PQU/G2770PF)

Auto / Analog / HDMI1/ HDMI2

Select input signal source. (E2770SHE)

Auto / Analog / DVI/HDMI

Select input signal source.(I2770VHE/M2870VHE/E2770SH)

Auto / Analog / DVI

Select input signal source. (E2770SD/M2770V/M2870V/I2770V/E2770SD6)

Auto / Analog / DVI / HDMI /DP

Select input signal source. (Q2770PQU/G2770PQU/M2870VQ/I2770PQ)

Yes or No

Auto adjust the picture to default.

0-24hrs

Select DC off time.

wide or 4:3 wide / 4:3 / 1:1 / 17″(4:3) / 19″(4:3) /19″w(16:10) / 21.5″w(16:9) / 22″w(16:10) / 23″w(16:9) / 23.6″w(16:9) / 24″w(16:9) / 24″w(16:10) Full / Square / 1:1 / 17″(4:3) / 19″(4:3) /19″(5:4)/19″W(16:10) / 21.5″W(16:9) / 22″W(16:10) / 23″W(16:9) / 23.6″W(16:9) / 24″W(16:9) Yes or No

Select wide or 4:3 format for display. Select image ratio for display.(G2770PQU)
Select image ratio for display.G2770PF Turn ON/OFF DDC-CI Support.

Yes or No

Reset the menu to default.

Show the information of the main image and sub-image source.

34

r

Exit

1 Press

(Menu) to display menu.

2 Press – or + to select

3 Press

to exit.

(Exit), and press

to enter.

Exit

Exit the main OSD.

35
r

LED Indicator
Status Full Power Mode Active-off Mode

Green or Blue Orange or red

LED Color

36
r

Drivers

Monitor Driver

Windows 2000
1. Start Windows® 2000 2. Click on the ‘Start’ button, point to ‘Settings’, and then click on ‘Control Panel’. 3. Double click on the ‘Display’ Icon. 4. Select the ‘Settings’ tab then click on ‘Advanced…’. 5. Select ‘Monitor’ – If the ‘Properties’ button is inactive, it means your monitor is properly configured. Please stop installation. – If the ‘Properties’ button is active. Click on ‘Properties’ button. Please follow the steps given below. 6. Click on ‘Driver’ and then click on ‘Update Driver…’ then click on the ‘Next’ button. 7. Select ‘Display a list of the known drivers for this device so that I can choose a specific driver’, then click on ‘Next’ and then click on ‘Have disk…’. 8. Click on the ‘Browse…’ button then select the appropriate drive F: ( CD-ROM Drive). 9. Click on the ‘Open’ button, then click on the ‘OK’ button. 10. Select your monitor model and click on the ‘Next’ button. 11. Click on the ‘Finish’ button then the ‘Close’ button. If you can see the ‘Digital Signature Not Found’ window, click on the ‘Yes’ button.
Windows ME
1. Start Windows® Me 2. Click on the ‘Start’ button, point to ‘Settings’, and then click on ‘Control Panel’. 3. Double click on the ‘Display’ Icon. 4. Select the ‘Settings’ tab then click on ‘Advanced…’. 5. Select the ‘Monitor’ button, then click on ‘Change…’ button. 6. Select ‘Specify the location of the driver(Advanced)’ and click on the ‘Next’ button. 7. Select ‘Display a list of all the drivers in a specific location, so you can choose the driver you want’, then click on ‘Next’ and then click on ‘Have Disk…’. 8. Click on the ‘Browse…’ button, select the appropriate drive F: ( CD-ROM Drive) then click on the ‘OK’ button. 9. Click on the ‘OK’ button, select your monitor model and click on the ‘Next’ button. 10. Click on ‘Finish’ button then the ‘Close’ button.
37
r

Windows XP
1. Start Windows® XP 2. Click on the ‘Start’ button and then click on ‘Control Panel’.
3. Select and click on the category `Appearance and Themes’
4. Click on the ‘Display’ Item.
38
r

5. Select the ‘Settings’ tab then click on the ‘Advanced’ button.
   6. Select ‘Monitor’ tab – If the ‘Properties’ button is inactive, it means your monitor is properly configured. Please stop installation. – If the ‘Properties’ button is active, click on ‘Properties’ button. Please follow the steps below.
   7. Click on the ‘Driver’ tab and then click on ‘Update Driver…’ button.
   39
   r

6. Select the ‘Install from a list or specific location [advanced]’ radio button and then click on the ‘Next’ button.
   9. Select the ‘Don’t Search. I will choose the driver to install’ radio button. Then click on the ‘Next’ button.
   10. Click on the ‘Have disk…’ button, then click on the ‘Browse…’ button and then select the appropriate drive F: (CD-ROM Drive).
   11. Click on the ‘Open’ button, then click the ‘OK’ button. 12. Select your monitor model and click on the ‘Next’ button. – If you can see the ‘has not passed Windows® Logo testing to verify its compatibility with Windows® XP’ message, please click on the ‘Continue Anyway’ button. 13. Click on the ‘Finish’ button then the ‘Close’ button. 14. Click on the ‘OK’ button and then the ‘OK’ button again to close the Display Properties dialog box.
   40
   r

Windows Vista
1. Click “Start ” and “Control Panel”. Then, double-click on “Appearance and Personalization”.
2. Click “Personalization” and then “Display Settings”. 3. Click “Advanced Settings…”.
41
r

4. Click “Properties” in the “Monitor” tab. If the “Properties” button is deactivated, it means the configuration for your monitor is completed. The monitor can be used as is. If the message “Windows needs…” is displayed, as shown in the figure below, click “Continue”.
   5. Click “Update Driver…” in the “Driver” tab.
   6. Check the “Browse my computer for driver software” checkbox and click “Let me pick from a list of device drivers on my computer”.
   7. Click on the ‘Have disk…’ button, then click on the ‘Browse…’ button and then select the appropriate drive F:Driver (CD-ROM Drive). 8. Select your monitor model and click on the ‘Next’ button. 9. Click “Close” “Close” “OK” “OK” on the following screens displayed in sequence.
   42
   r

Windows 7
1.Start Windows® 7 2.Click on the ‘Start’ button and then click on ‘Control Panel’.
3. Click on the ‘Display’ icon.
43
r

4.Ckick on the “Change display settings” button. 5.Click the “Advanced Settings” button. 6.Click the “Monitor” tab and then click the “Properties” button.
44
r

7.Click the “Driver” tab.
8. Open the “Update Driver Software-Generic PnP Monitor” window by clicking on “Update Driver… “and then click the “Browse my computer for driver software” button.
9. Select “Let me pick from a list of device drivers on my computer”.
45
r

10. Click the “Have Disk” button. Click on the “Browse” button and navigate to the following directory: X:Drivermodule name (where X is the drive letter designator for the CD-ROM drive).
    11. Select the “xxx.inf” file and click the “Open” button. Click the “OK” button. 12. Select your monitor model and click the “Next” button. The files will be copied from the CD to your hard disk drive. 13. Close all open windows and remove the CD. 14. Restart the system. The system will automatically select the maximum refresh rate and corresponding Color Matching Profiles.
    46
    r

Windows 8
1. Start Windows® 8 2. Right click and click All apps at the bottom-right of the screen.
3. Click on the “Control panel” icon 4. Set the “View by” to “Large icons” or “Small icons”.
5. Click on the “Display” icon. 47
r

6. Click on the “Change display settings” button. 7. Click the “Advanced Settings” button.
   8. Click the “Monitor” tab and then click the “Properties” button. 48
   r

7. Click the “Driver” tab.
   10. Open the “Update Driver Software-Generic PnP Monitor” window by clicking on “Update Driver… ” and then click the “Browse my computer for driver software” button.
   11. Select “Let me pick from a list of device drivers on my computer”. 49
   r

8. Click the “Have Disk” button. Click on the “Browse” button and navigate to the following directory: X:Drivermodule name (where X is the drive letter designator for the CD-ROM drive).
   13. Select the “xxx.inf” file and click the “Open” button. Click the “OK” button. 14. Select your monitor model and click the “Next” button. The files will be copied from the CD to your hard disk
   drive. 15. Close all open windows and remove the CD. 16. Restart the system. The system will automatically select the maximum refresh rate and corresponding Color
   Matching Profiles.
   50
   r

i-Menu
Welcome to “i-Menu” software by AOC. i-Menu makes it easy to adjust your monitor display setting by using on screen menus instead of the OSD button on the monitor. To complete installation, please follow the installation guide.
51
r

e-Saver
Welcome to use AOC e-Saver monitor power management software! The AOC e-Saver features Smart Shutdown functions for your monitors, allows your monitor to timely shutdown when PC unit is at any status (On, Off, Sleep or Screen Saver); the actual shutdown time depends on your preferences (see example below). Please click on “driver/e-Saver/setup.exe” to start installing the e-Saver software, follow the install wizard to complete software installation. Under each of the four PC status, you may choose from the pull-down menu the desired time (in minutes) for your monitor to automatically shutdown. The example above illustrated: 1) The monitor will never shutdown when the PC is powered on. 2) The monitor will automatically shutdown 5 minutes after the PC is powered off. 3) The monitor will automatically shutdown 10 minutes after the PC is in sleep/stand-by mode. 4) The monitor will automatically shutdown 20 minutes after the screen saver appears.
You can click “RESET” to set the e-Saver to its default settings like below.
52
r

Screen+
Welcome to “Screen+” software by AOC, Screen+ software is a desktop screen splitting tool, it splits the desktop into different panes, each pane displays a different window. You only need to drag the window to a corresponding pane, when you want to access it. It supports multiple monitor display to make your task easier. Please follow the installation software to install it.
53
r

Troubleshoot

Problem & Question Power LED Is Not ON
No images on the screen

Possible Solutions
Make sure the power button is ON and the Power Cord is properly connected to a grounded power outlet and to the monitor.
Is the power cord connected properly? Check the power cord connection and power supply.
Is the signal cable connected correctly? (Connected using the signal cable) Check the signal cable connection.
If the power is on, reboot the computer to see the initial screen (the login screen), which can be seen. If the initial screen (the login screen) appears, boot the computer in the applicable mode (the safe mode for Windows ME/XP/2000) and then change the frequency of the video card. (Refer to the Setting the Optimal Resolution) If the initial screen (the login screen) does not appear, contact the Service Center or your dealer.
Can you see “Input Not Supported” on the screen? You can see this message when the signal from the video card exceeds the maximum resolution and frequency that the monitor can handle properly. Adjust the maximum resolution and frequency that the monitor can handle properly.
Make sure the AOC Monitor Drivers are installed.

Picture Is Fuzzy & Has Ghosting Shadowing Problem

Adjust the Contrast and Brightness Controls. Press to auto adjust. Make sure you are not using an extension cable or switch box. We recommend plugging the monitor directly to the video card output connector on the back .

Picture Bounces, Flickers Or Wave Pattern Appears In The Picture

Move electrical devices that may cause electrical interference as far away from the monitor as possible. Use the maximum refresh rate your monitor is capable of at the resolution your are using.

54

r

Monitor Is Stuck In Active Off-Mode”

The Computer Power Switch should be in the ON position. The Computer Video Card should be snugly fitted in its slot. Make sure the monitor’s video cable is properly connected to the computer. Inspect the monitor’s video cable and make sure no pin is bent. Make sure your computer is operational by hitting the CAPS LOCK key on the keyboard while observing the CAPS LOCK LED. The LED should either turn ON or OFF after hitting the CAPS LOCK key.

Missing one of the primary colors (RED, GREEN, or BLUE)

Inspect the monitor’s video cable and make sure that no pin is damaged. Make sure the monitor’s video cable is properly connected to the computer.

Screen image is not centered Adjust H-Position and V-Position or press hot-key (Power/AUTO).
or sized properly Picture has color defects
Adjust RGB color or select desired color temperature. (white does not look white)

Horizontal or vertical disturbances on the screen

Use Windows 95/98/2000/ME/XP shut-down mode Adjust CLOCK and FOCUS. Press to auto-adjust.

Display not on whole screen in default resolution ration

Use I-menu software from CD(or download from AOC official website), select “reset” option to adjust.

55
r

Specification

General Specification

E2770SD /E2770SHE/M2770V/I2770V/I2770VHE/E2770SD6/E2770SH

Panel

Product name Driving system Viewable Image Size Pixel pitch Video Separate Sync. Display Color Dot Clock

E2770SD/E2770SD6/E2770SHE/M2770V/I2770V/I2770VHE/E2770SH
TFT Color LCD
68.6cm diagonal
0.3114mm(H)X0.3114mm(V) R, G, B Analog lnterface & Digital Interface H/V TTL 16.7M Colors 148.5MHz

Horizontal scan range

30 kHz – 83 kHz

Horizontal scan Size(Maximum)

597.89mm

Vertical scan range 50 Hz – 76 Hz

Vertical scan Size(Maximum)

336.31mm

Optimal preset resolution

1920x 1080 @60 Hz

Plug & Play

VESA DDC2B/CI

E2770SD/ E2770SD6/M2770V/I2770V:D-Sub 15pin; DVI 24pin

Resolution Input Connector

E2770SHE:D-Sub 15pin;;HDMI I2770VHE/E2770SH: D-Sub 15pin; DVI 24pin; HDMI;

Input Video Signal Analog: 0.7Vp-p(standard), 75 OHM, TMDS

Power Source

100-240V~, 50/60Hz

Typical

power

consumption

Power Consumption
Power consumption @power-saving Off timer

E2770SD /E2770SD6/I2770V30W E2770SHE/I2770VHE32W M2770V/E2770SH:38W (Test condition: set Contrast = 50, Brightness = 90) E2770SD /E2770SD6/I2770V32W E2770SHE/I2770VHE/E2770SH40W M2770V/E2770SH:44W (Test condition: Set Brightness and Contrast to maximum)
0.5W
0-24 hrs

Speakers

2WX2(E2770SH)

Physical Connector Type
Characteristics

E2770SD/M2770V/I2770V /E2770SD6:D-Sub ; DVI-D E2770SHE:D-Sub ; HDMI

56

r

Signal Cable Type Temperature: Environmental Humidity: Altitude:

I2770VHE/E2770SH: D-Sub ; DVI-D;HDMI; Detachable

Operating Non-Operating Operating Non-Operating Operating Non-Operating

0° to 40° -25°to 55° 10% to 85% (non-condensing) 5% to 93% (non-condensing) 0~ 3658m (0~ 12000 ft ) 0~ 12192m (0~ 40000 ft )

57
r

E2770PQU/I2770PQ

Panel

Product name Driving system Viewable Image Size Pixel pitch Video Separate Sync. Display Color Dot Clock

Horizontal scan range

Horizontal scan Size(Maximum)

Vertical scan range

Vertical scan Size(Maximum)

Optimal preset resolution

Plug & Play

Resolution

Input Connector
Input Video Signal Power Source

Typical power consumption

Power Consumption

Power consumption @power-saving Off timer
Speakers

Physical

Connector Type

Characteristics Signal Cable Type

Temperature:

Environmental Humidity:

Altitude:

E2770PQU/I2770PQ TFT Color LCD 68.6cm diagonal 0.3114mm(H)X0.3114mm(V) R, G, B Analog lnterface & Digital Interface H/V TTL 16.7M Colors 148.5MHz

30 kHz – 83 kHz
597.89mm
50 Hz – 76 Hz
336.31mm
1920x 1080 @60 Hz
VESA DDC2B/CI
E2770PQU:D-Sub 15pin; DVI 24pin; HDMI(MHL) ;DP
I2770PQ:D-Sub 15pin; DVI 24pin; HDMI ;DP
Analog: 0.7Vp-p(standard), 75 OHM, TMDS
100-240V~, 50/60Hz E2770PQU32W I2770PQ:31W (Test condition: set Contrast = 50, Brightness = 90) E2770PQU40W I2770PQ:39W (Test condition: Set Brightness and Contrast to maximum) 0.5W 0-24 hrs 2WX2

15-pin D-Sub DVI-D HDMI DP Detachable

Operating Non-Operating Operating Non-Operating Operating Non-Operating

0° to 40° -25°to 55° 10% to 85% (non-condensing) 5% to 93% (non-condensing) 0~ 3658m (0~ 12000 ft ) 0~ 12192m (0~ 40000 ft )

58
r

Q2770PQU

Panel

Resolution
Physical Characteristics Environmental

Model name Driving system Viewable Image Size Pixel pitch Video Separate Sync. Display Color Dot Clock Horizontal scan range Horizontal scan range Horizontal scan Size(Maximum) Vertical scan range Vertical scan Size(Maximum) Optimal preset resolution Optimal preset resolution
Plug & Play Input Connector Input Video Signal Power Source
Typical power consumption
Power Consumption Power consumption @power-saving Off timer Speakers Connector Type Signal Cable Type Temperature: Operating Non-Operating Humidity: Operating Non-Operating Altitude: Operating Non-Operating

Q2770PQU TFT Color LCD 68.6cm diagonal 0.233mm(H)X0.233mm(V) R, G, B Analog lnterface & Digital Interface H/V TTL 16.7M Colors 241.5MHz 30 kHz – 83 kHz for D-Sub 30 kHz – 99 kHz for DVI (dual link) ; HDMI ; DP 596.74mm
50 Hz – 76 Hz 335.66mm 1920x 1080 @60 Hz for D-Sub 2560x 1440 @60 Hz for DVI (dual link) ; HDMI ; DP only VESA DDC2B/CI D-Sub 15pin; DVI 24pin; HDMI;DP Analog: 0.7Vp-p(standard), 75 OHM, TMDS 100-240V~, 50/60Hz 45W(Test condition: set Contrast = 50, Brightness = 90) 50W(Test condition: Set Brightness and Contrast to maximum) 0.5W 0-24 hrs 2WX2 15-pin D-Sub DVI-D HDMI DP Detachable
0° to 40° -25° to 55°
10% to 85% (non-condensing) 5% to 93% (non-condensing)
0~ 3658m (0~ 12000 ft ) 0~ 12192m (0~ 40000 ft )

59
r

G2770PQU/G2770PF

Panel
Resolution Physical Characteristics
Environmental

Model name Driving system Viewable Image Size Pixel pitch Video Separate Sync. Display Color Dot Clock Horizontal scan range Horizontal scan range Horizontal scan range G2770PF Horizontal scan Size(Maximum) Vertical scan range Vertical scan range Vertical scan range G2770PF Vertical scan Size(Maximum) Optimal preset resolution Optimal preset resolution Plug & Play Input Connector Input Connector G2770PF Input Video Signal Power Source Typical power consumption
Power Consumption Power consumption @power-saving Off timer Speakers Connector Type Connector Type G2770PF Signal Cable Type Temperature: Operating Non- Operating Humidity: Operating Non-Operating Altitude: Operating Non-Operating

G2770PQU/G2770PF TFT Color LCD 68.6cm diagonal 0.311mm(H)X0.311mm(V) R, G, B Analog lnterface & Digital Interface H/V TTL 16.7M Colors 330MHz 30 kHz – 83 kHz 30 kHz – 160 kHz for DVI (dual link) ; DP only 160 kHz – 160 kHz for DP only 597.6mm 50 Hz – 76 Hz 50Hz~146Hz for DVI (dual link) ; DP only 48Hz~146Hz for DP only 336.15mm 1920x 1080 @60 Hz 1920x 1080 @144 Hz for DVI (dual link) ; DP only VESA DDC2B/CI D-Sub 15pin; DVI 24pin; HDMI;DP D-Sub 15pin; DVI 24pin; HDMI/ MHL;DP; Analog: 0.7Vp-p(standard), 75 OHM, TMDS 100-240V~, 50/60Hz 45W(Test condition: set Contrast = 50, Brightness = 90) 55W(Test condition: Set Brightness and Contrast to maximum) 0.5W 0-24 hrs 2WX2 15-pin D-Sub DVI-D HDMI DP 15-pin D-Sub DVI-D HDMI/ MHL DP Detachable
0° to 40° -25° to 55°
10% to 85% (non-condensing) 5% to 93% (non-condensing)
0~ 3658m (0~ 12000 ft ) 0~ 12192m (0~ 40000 ft )

60

r

M2870V/ M2870VQ/M2870VHE

Panel

Model name

Driving system

Viewable Image Size

Pixel pitch

Video

Separate Sync.

Display Color

Dot Clock

Resolution

Horizontal scan range

Horizontal scan Size(Maximum)

Vertical scan range

Vertical scan Size(Maximum)

Optimal preset resolution

Plug & Play

Input Connector

Physical Characteristics
Environmental

Input Video Signal Power Source
Typical power consumption
Power Consumption Power consumption @power-saving Off timer Speakers Connector Type
Signal Cable Type Temperature: Operating Non-Operating Humidity: Operating Non-Operating Altitude: Operating Non-Operating

M2870V/ M2870VQ/M2870VHE TFT Color LCD 71.1cm diagonal 0.32mm(H)X0.32mm(V) R, G, B Analog lnterface & Digital Interface H/V TTL 16.7M Colors 148.5MHz 30 kHz – 83 kHz 620.9mm 50 Hz – 76 Hz 341.2mm 1920x 1080 @60 Hz VESA DDC2B/CI (M2870V)D-Sub 15pin; DVI 24pin (M2870VHE)D-Sub 15pin; DVI 24pin; HDMI; (M2870VQ)D-Sub 15pin; DVI 24pin; HDMI;DP Analog: 0.7Vp-p(standard), 75 OHM, TMDS 100-240V~, 50/60Hz 41W(Test condition: set Contrast = 50, Brightness = 90) 49W(Test condition: Set Brightness and Contrast to maximum) 0.5W 0-24 hrs 2WX2 (M2870VQ) M2870V:D-Sub ; DVI-D M2870VHE:D-Sub ; DVI-D,HDMI M2870VQ:D-Sub ; DVI-D,HDMI;DP Detachable
0° to 40° -25° to 55°
10% to 85% (non-condensing) 5% to 93% (non-condensing)
0~ 3658m (0~ 12000 ft ) 0~ 12192m (0~ 40000 ft )

61
r

Preset Display Modes

E2770SD/E2770SD6/E2770SHE/E2770PQU/M2770V/M2870V/I2770V/I2770VHE/M2870VHE/ M2870VQ/I2770PQ/E2770SH

Standard

Resolution

1. Frequency (kHz)
2. Frequency (Hz)

VGA

640 X 480@60Hz

31.469

59.94

MAC

640 X 480@67Hz

35

MODE

66.667

VGA

640 X 480@72Hz

37.861

72.809

VGA

640 X 480@75Hz

37.5

75

IBM MODE

720 X 400@70Hz

31.469

70.087

800 X 600@56Hz

35.156

56.25

SVGA

800 X 600@60Hz 800 X 600@72Hz

37.879 48.077

60.317 72.188

800 X 600@75Hz

46.875

75

MAC MODE

832 X 624@75Hz

49.725

74.551

1024 X 768@60Hz

48.363

60.004

XGA

1024 X 768@70Hz

56.476

70.069

1024 X 768@75Hz

60.023

75.029

1280 X 960@60Hz

60

60

SXGA

1280 X 1024@60Hz 1280 X 1024@75Hz

63.981 79.976

60.02 75.025

1280X 720@60Hz

44.772

59.855

WXGA+

1440 X 900@60Hz

55.935

59.876

WSXGA+

1680 X 1050@60Hz

65.29

59.95

FHD

1920 X 1080@60Hz

67.5

60

62
r

Q2770PQU Standard VGA
MAC MODE VGA VGA
IBM MODE
SVGA
MAC MODE
XGA
SXGA
WXGA+ WSXGA+
FHD WQHD

Resolution
640 X 480@60Hz 640 X 480@67Hz 640 X 480@72Hz 640 X 480@75Hz 720 X 400@70Hz 800 X 600@56Hz 800 X 600@60Hz 800 X 600@72Hz 800 X 600@75Hz 832 X 624@75Hz 1024 X 768@60Hz 1024 X 768@70Hz 1024 X 768@75Hz 1280 X 960@60Hz 1280 X 1024@60Hz 1280 X 1024@75Hz 1280X 720@60Hz 1440 X 900@60Hz 1680 X 1050@60Hz 1920 X 1080@60Hz 2560 X 1440@60Hz

31. Frequency (kHz)
    31.469 35
    37.861 37.5
    31.469 35.156 37.879 48.077 46.875 49.725 48.363 56.476 60.023
    60 63.981 79.976 44.772 55.935 65.29
    67.5 88.787

32. Frequency (Hz)
    59.94 66.667 72.809
    75 70.087 56.25 60.317 72.188
    75 74.551 60.004 70.069 75.029
    60 60.02 75.025 59.855 59.876 59.95
    60 60

WQHD Mode(2560×1440) for Q2770PQU model DVI(dual link), Display Port only; For HDMI, the highest supporting screen resolution is also 2560 x 1440, but it always depends on your capability of graphics card and BluRay/video players.

63
r

G2770PQU/G2770PF
Standard

VGA

SVGA
XGA SXGA WXGA (DVI/HDMI/DP) WSXGA (DVI/HDMI/DP)
HD *** (DVI/HDMI/DP) IBM MODES DOS MAC MODES VGA MAC MODES SVGA
HD(only DVI/DP)

Resolution
640×480@60Hz 640×480@72Hz 640×480@75Hz 800×600@56Hz 800×600@60Hz 800×600@72Hz 800×600@75Hz 800×600@100Hz 1024×768@60Hz 1024×768@70Hz 1280×1024@60Hz
1440×900@60Hz
1680×1050@60Hz
1920×1080@60Hz
1280×720@60Hz
720×400@70Hz 640×480@67Hz 832×624@75Hz 1920×1080@100Hz 1920×1080@120Hz 1920×1080@144Hz

31. Frequency (kHz)
    31.469 37.861
    37.5 35.156 37.879 48.077 46.875 46.875 48.363 56.476 63.981

32. Frequency (Hz)
    59.94 72.809
    75 56.25 60.317 72.188
    75 75 60.004 70.069 60.02

55.935

59.887

65.29
67.5
45
31.469 35
49.725 113.3 137.2 158.1

59.954
60
60
70.087 66.667 74.551
100 120 144

HDMI/DP Timing(E2770SHE/E2770PQU/Q2770PQU/G2770PQU /I2770VHE/M2870VQ/M2870VHE/ E2770SH/G2770PF)

Format 480P 480P 576P 720P 1080P

Resolution 640 X 480 720 X 480 720 X 576 1280 X 720 1920 X 1080

Vertical frequency 60Hz 60Hz 50Hz
50Hz,60Hz 50Hz,60Hz

MHL Timing(E2770PQU/ G2770PF)

Format 480P 480P 576P 720P 1080P

Resolution 640 X 480 720 X 480 720 X 576 1280 X 720 1920 X 1080

Type SD SD SD HD HD

Vertical frequency 60Hz 60Hz 50Hz
50Hz,60Hz 30Hz,50Hz,60Hz 64

r

Pin Assignments

15-Pin Color Display Signal Cable

Pin No. 1 2 3 4 5 6 7 8

Signal Name Video-Red Video-Green Video-Blue N.C. Detect Cable GND-R GND-G GND-B

Pin No. 9 10 11 12 13 14 15

Signal Name +5V Ground N.C. DDC-Serial data H-sync V-sync DDC-Serial clock

24-Pin Color Display Signal Cable

Pin Number
1 2 3 4 5 6 7 8 9 10 11 12

24-Pin Color Display Signal Cable TMDS data 2 TMDS data 2 TMDS data 2/4 Shield TMDS data 4 TMDS data 4
DDC Clock DDC Data N.C. TMDS data 1 TMDS data 1 TMDS data 1/3 Shield TMDS data 3

Pin Number
13 14 15 16 17 18 19 20 21 22 23 24

24-Pin Color Display Signal Cable TMDS data 3 5V Power Ground (for+5V) Hot Plug Detect TMDS data 0 TMDS data 0 TMDS data 0/5 Shield TMDS data 5 TMDS data 5
TMDS Clock Shield TMDS Clock + TMDS Clock

65
r

19-Pin Color Display Signal Cable

Pin No. Signal Name

Pin No. Signal Name

1

TMDS Data 2+

9

TMDS Data 0

2

TMDS Data 2 Shield

10

TMDS Clock +

3

TMDS Data 2

11

TMDS Clock Shield

4

TMDS Data 1+

12

TMDS Clock

5

TMDS Data 1Shield

13

CEC

6

TMDS Data 1

14

Reserved (N.C. on device

7

TMDS Data 0+

15

SCL

8

TMDS Data 0 Shield

16

SDA

Pin Signal Name No. 17 DDC/CEC Ground 18 +5V Power 19 Hot Plug Detect

20-Pin Color Display Signal Cable

Pin No. 1 2 3 4 5 6 7 8 9 10

Signal Name ML_Lane 3 (n) GND ML_Lane 3 (p) ML_Lane 2 (n) GND ML_Lane 2 (p) ML_Lane 1 (n) GND ML_Lane 1 (p) ML_Lane 0 (n)

Pin No. 11 12 13 14 15 16 17 18 19 20

Signal Name GND ML_Lane 0 (p) CONFIG1 CONFIG2 AUX_CH(p) GND AUX_CH(n) Hot Plug Detect Return DP_PWR DP_PWR

66
r

Plug and Play
Plug & Play DDC2B Feature This monitor is equipped with VESA DDC2B capabilities according to the VESA DDC STANDARD. It allows the monitor to inform the host system of its identity and, depending on the level of DDC used, communicate additional information about its display capabilities. The DDC2B is a bi-directional data channel based on the I2C protocol. The host can request EDID information over the DDC2B channel.
67
r

Regulation

FCC Notice
FCC Class B Radio Frequency Interference Statement WARNING: (FOR FCC CERTIFIED MODELS) NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help.
NOTICE : The changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Shielded interface cables and AC power cord, if any, must be used in order to comply with the emission limits. The manufacturer is not responsible for any radio or TV interference caused by unauthorized modification to this equipment. It is the responsibilities of the user to correct such interference. It is the responsibility of the user to correct such interference.
68
r

WEEE DeclarationOptional
Disposal of Waste Equipment by Users in Private Household in the European Union.
This symbol on the product or on its packaging indicates that this product must not be disposed of with your other household waste.Instead, it is your responsibility to dispose of your waste equipment by handing it over to a designated collection point for the recycling of waste electrical and electronic equipment.The separate collection and recycling of your waste equipment at the time of disposal will help to conserve natural resources and ensure that it is recycled in a manner that protects human health and the environment. For more information about where you can drop off your waste equipment for recycling, please contact your local city office, your household waste disposal service or the shop where you purchased the product .
WEEE Declaration for IndiaOptional
This symbol on the product or on its packaging indicates that this product must not be disposed of with your other household waste. Instead it is your responsibility to dispose of your waste equipment by handing it over to a designated collection point for the recycling of waste electrical and electronic equipment. The separate collection and recycling of your waste equipment at the time of disposal will help to conserve natural resources and ensure that it is recycled in a manner that protects human health and the environment. For more information about where you can drop off your waste equipment for recycling in India please visit the below web link. www.aocindia.com/ewaste.php. This product complies with all implemented RoHS type regulations worldwide, including but not limited to, EU, Korea, Japan, US States (e.g. California), Ukraine, Serbia, Turkey, Vietnam and India. We continue to monitor, influence and develop our processes to comply with upcoming proposed RoHS type regulations, including but not limited to, Brazil, Argentina, Canada.
Restriction on Hazardous Substances statement (India)
This product complies with the “India E-waste Rule 2011” and prohibits use of lead, mercury, hexavalent chromium, polybrominated biphenyls or polybromi- nated diphenyl ethers in concentrations exceeding 0.1 weight % and 0.01 weight % for cadmium, except for the exemptions set in Schedule 2 of the Rule.
69
r

EPA Energy Star
ENERGY STAR® is a U.S. registered mark. As an ENERGY STAR® Partner, AOC International (Europe) BV and Envision Peripherals, Inc. have determined that this product meets the ENERGY STAR® guidelines for energy efficiency. (FOR EPA CERTIFIED MODELS)
EPEAT Declaration
EPEAT is a system to help purchasers in the public and private sectors evaluate, compare and select desktop computers, notebooks and monitors based on their environmental attributes. EPEAT also provides a clear and consistent set of performance criteria for the design of products, and provides an opportunity for manufacturers to secure market recognition for efforts to reduce the environmental impact of its products.
AOC believes in protecting the environment. With a key concern for the conservation of natural resources, as well as landfill protection, AOC announces the launch of AOC monitor’s packaging recycling program. This program is designed to help you discard of your monitor carton and filler materials properly. If a local recycling center is not available, AOC will recycle the packaging material for you, including foam filler and carton. AOC Display solution will only recycle AOC monitor packaging. Please refer to the following website address: Only for North and South American, excluding Brazil: http://us.aoc.com/about/environmental_impact For Germany: http://www.aoc-europe.com/en/service/tco.php For Brazil: http://www.aoc.com.br/2007/php/index.php?req=pagina&pgn_id=134 (FOR EPEAT Silver CERTIFIED MODELS)
70
r

EPEAT Declaration
EPEAT is a system to help purchasers in the public and private sectors evaluate, compare and select desktop computers, notebooks and monitors based on their environmental attributes. EPEAT also provides a clear and consistent set of performance criteria for the design of products, and provides an opportunity for manufacturers to secure market recognition for efforts to reduce the environmental impact of its products. AOC believes in protecting the environment. With a key concern for the conservation of natural resources, as well as landfill protection, AOC announces the launch of AOC monitor’s packaging recycling program. This program is designed to help you discard of your monitor carton and filler materials properly. If a local recycling center is not available, AOC will recycle the packaging material for you, including foam filler and carton. AOC Display solution will only recycle AOC monitor packaging. Please refer to the following website address: Only for North and South American, excluding Brazil: http://us.aoc.com/about/environmental_impact For Germany: http://www.aoc- europe.com/en/service/tco.php For Brazil: http://www.aoc.com.br/2007/php/index.php?req=pagina&pgn_id=134 (FOR EPEAT GOLD CERTIFIED MODELS)
71
r

TCO DOCUMENT
(FOR TCO CERTIFIED MODELS) 72
r

Service

Warranty Statement for Europe

LIMITED THREE-YEAR WARRANTY
For AOC LCD Monitors sold within Europe, AOC International (Europe) B.V. warrants this product to be free from defects in material and workmanship for a period of Three (3) years after the original date of consumer purchase. During this period, AOC International (Europe) B.V. will, at its option, either repair the defective product with new or rebuilt parts, or replace it with a new or rebuilt product at no charge except as stated below. In the absent of the proof of purchase, the warranty will start 3 months after the date of manufacturing indicated on the product.
If the product appears to be defective, please contact your local dealer or refer to the service and support section on www.aoc-europe.com for the warranty instructions in your country. The freight cost for the warranty is pre-paid by AOC for the delivery and return. Please ensure you provide a dated proof of purchase along with the product and deliver to the AOC Certified or Authorized Service Center under the following condition:
Make sure the LCD Monitor is packed in a proper carton box (AOC prefers the original carton box to protects your monitor well enough during transport).
Put the RMA number on the address label Put the RMA number on the shipping carton
AOC International (Europe) B.V. will pay the return shipping charges within one of the countries specified within this warranty statement. AOC International (Europe) B.V. is not responsible for any costs associated with the transportation of product across international borders. This includes the international border within the European Union. If the LCD Monitor is not available for collection when the currier attends, you will be charged a collection fee.

• This limited warranty does not cover any losses or damages that occur as a result of:
  Damages during transport due to improper packaging Improper installation or maintenance other then in accordance with AOC’s user manual Misuse Neglect Any cause other than ordinary commercial or industrial application Adjustment by non-authorized source Repair, modification, or installation of options or parts by anyone other than an AOC Certified or
  Authorized Service Center Improper environments like humidity, water damage and dusts Damaged by violence, earthquake and terrorist attacks Excessive or inadequate heating or air conditioning or electrical powers failures, surges, or other
  irregularities
  This limited warranty does not cover any of the product firmware or hardware that you or any third party have modified or altered; you bear the sole responsibility and liability for any such modifications or alteration.
  73
  r

All AOC LCD Monitors are produced according to the ISO 9241-307 Class 1 pixel policy standards. If your warranty has expired, you still have access to all available service options, but you will be responsible for the cost of service, including parts, labor, shipping (if any) and applicable taxes. AOC Certified or Authorized Service Center will provide you with an estimate of service costs before receiving your authorization to perform service. ALL EXPRESS AND IMPLIED WARRANTIES FOR THIS PRODUCT (INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE) ARE LIMITED IN DURATION TO A PERIOD OF THREE (3) YEARS FOR PARTS AND LABOR FROM THE ORIGINAL DATE OF CONSUMER PURCHASE. NO WARRANTIES (EITHER EXPRESSED OR IMPLIED) APPLY AFTER THIS PERIOD. AOC INTERNATIONAL (EUROPE) B.V. OBLIGATIONS AND YOUR REMEDIES HEREUNDER ARE SOLELY AND EXCULSIVELY AS STATED HERE. AOC INTERNATIONAL (EUROPE) B.V. LIABILITY, WHETHER BASED ON CONTRACT, TORT, WARRANTY, STRICT LIABILITY, OR OTHER THEORY, SHALL NOT EXCEED THE PRICE OF THE INDIVIDUAL UNIT WHOSE DEFECT OR DAMAGE IS THE BASIS OF THE CLAIM. IN NO EVENT SHALL AOC INTERNATIONAL (EUROPE) B.V. BE LIABLE FOR ANY LOSS OF PROFITS, LOSS OF USE OR FACILITIES OR EQUIPMENT, OR OTHER INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGE. SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION MAY NOT APPLY TO YOU. ALTHOUGH THIS LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, YOU MAY HAVE OTHER RIGHTS, WHICH MAY VARY FROM COUNTRY TO COUNTRY. THIS LIMITED WARRANTY IS ONLY VALID FOR PRODUCTS PURCHASED IN THE MEMBER COUNTRIES OF THE EUROPEAN UNION.
Information in this document is subject to change without notice. For more information, please visit: http://www.aoc-europe.com
74
r

Warranty Statement for Middle East and Africa (MEA)
And
The Commonwealth of Independent States (CIS)
LIMITED ONE to THREE YEARS WARRANTY
For AOC LCD Monitors sold within the Middle East and Africa (MEA) and the Commonwealth of Independent States (CIS), AOC International (Europe) B.V. warrants this product to be free from defects in material and workmanship for a period of One (1) to Three (3) years from the manufacture date depending on sale country. During this period, AOC International (Europe) B.V. offers a Carry-In (return to Service Center) Warranty Support at an AOC’s Authorized Service Center or Dealer and at its option, either repair the defective product with new or rebuilt parts, or replace it with a new or rebuilt product at no charge except as stated below. As a Standard Policy, the warranty will be calculated from the manufacture date identified from the product ID serial number, but the total warranty will be Fifteen (15) months to Thirty Nine (39) months from MFD (manufacture date) depending on sale country. Warranty will be considered for exceptional cases that are out of warranty as per the product ID serial number and for such exceptional cases; Original Invoice/Proof Of Purchase Receipt is mandatory.
If the product appears to be defective, please contact your AOC authorized dealer or refer to the service and support section on AOC’s website for the warranty instructions in your country:
Egypt: http://aocmonitorap.com/egypt_eng CIS Central Asia: http://aocmonitorap.com/ciscentral Middle East: http://aocmonitorap.com/middleeast South Africa: http://aocmonitorap.com/southafrica Saudi Arabia: http://aocmonitorap.com/saudiarabia
Please ensure you provide a dated proof of purchase along with the product and deliver to the AOC Authorized Service Center or Dealer under the following condition:
Make sure the LCD Monitor is packed in a proper carton box (AOC prefers the original carton box to protects your monitor well enough during transport).
Put the RMA number on the address label Put the RMA number on the shipping carton

• This limited warranty does not cover any losses or damages that occur as a result of:
  Damages during transport due to improper packaging Improper installation or maintenance other then in accordance with AOC’s user manual Misuse Neglect Any cause other than ordinary commercial or industrial application Adjustment by non-authorized source
  75
  r

Repair, modification, or installation of options or parts by anyone other than an AOC Certified or Authorized Service Center
Improper environments like humidity, water damage and dusts Damaged by violence, earthquakes and terrorist attacks Excessive or inadequate heating or air conditioning or electrical powers failures, surges, or other
irregularities This limited warranty does not cover any of the product firmware or hardware that you or any third party have modified or altered; you bear the sole responsibility and liability for any such modifications or alteration.
All AOC LCD Monitors are produced according to the ISO 9241-307 Class 1 pixel policy standards.
If your warranty has expired, you still have access to all available service options, but you will be responsible for the cost of service, including parts, labor, shipping (if any) and applicable taxes. AOC Certified, Authorized Service Center or dealer will provide you with an estimate of service costs before receiving your authorization to perform service.
ALL EXPRESS AND IMPLIED WARRANTIES FOR THIS PRODUCT (INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE) ARE LIMITED IN DURATION TO A PERIOD OF ONE (1) to THREE (3) YEARS FOR PARTS AND LABOR FROM THE ORIGINAL DATE OF CONSUMER PURCHASE. NO WARRANTIES (EITHER EXPRESSED OR IMPLIED) APPLY AFTER THIS PERIOD. AOC INTERNATIONAL (EUROPE) B.V. OBLIGATIONS AND YOUR REMEDIES HEREUNDER ARE SOLELY AND EXCULSIVELY AS STATED HERE. AOC INTERNATIONAL (EUROPE) B.V. LIABILITY, WHETHER BASED ON CONTRACT, TORT, WARRANTY, STRICT LIABILITY, OR OTHER THEORY, SHALL NOT EXCEED THE PRICE OF THE INDIVIDUAL UNIT WHOSE DEFECT OR DAMAGE IS THE BASIS OF THE CLAIM. IN NO EVENT SHALL AOC INTERNATIONAL (EUROPE) B.V. BE LIABLE FOR ANY LOSS OF PROFITS, LOSS OF USE OR FACILITIES OR EQUIPMENT, OR OTHER INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGE. SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION MAY NOT APPLY TO YOU. ALTHOUGH THIS LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, YOU MAY HAVE OTHER RIGHTS, WHICH MAY VARY FROM COUNTRY TO COUNTRY. THIS LIMITED WARRANTY IS ONLY VALID FOR PRODUCTS PURCHASED IN THE MEMBER COUNTRIES OF THE EUROPEAN UNION.
Information in this document is subject to change without notice. For more information, please visit: http://www.aocmonitorap.com
76
r

AOC Pixel Policy ISO 9241-307 Class 1
77
r

Warranty Statement for North & South America (excluding Brazil)
WARRANTY STATEMENT for AOC Color Monitors Including those Sold within North America as Specified
Envision Peripherals, Inc. warrants this product to be free from defects in material and workmanship for a period of three (3) years for parts & labor and one (1) year for CRT Tube or LCD Panel after the original date of consumer purchase. During this period, EPI ( EPI is the abbreviation of Envision Peripherals, Inc. ) will, at its option, either repair the defective product with new or rebuilt parts, or replace it with a new or rebuilt product at no charge except as *stated below. The parts or product that are replaced become the property of EPI.
In the USA to obtain service under this limited warranty, call EPI for the name of the Authorized Service Center closest to your area. Deliver the product freight pre-paid, along with the dated proof of purchase, to the EPI Authorized Service Center. If you cannot deliver the product in person:
Pack it in its original shipping container (or equivalent) Put the RMA number on the address label Put the RMA number on the shipping carton Insure it (or assume the risk of loss/damage during shipment) Pay all shipping charges
EPI is not responsible for damage to inbound product that was not properly packaged. EPI will pay the return shipment charges within one of the countries specified within this warranty statement. EPI is not responsible for any costs associated with the transportation of product across international borders. This includes the international borders of the countries within this warranty statements.
In the United States and Canada contact your Dealer or EPI Customer Service, RMA Department at the toll free number 888-662-9888. Or you can request an RMA Number online at www.aoc.com/na-warranty.

• This limited warranty does not cover any losses or damages that occur as a result of:
  Shipping or improper installation or maintenance Misuse Neglect Any cause other than ordinary commercial or industrial application Adjustment by non- authorized source Repair, modification, or installation of options or parts by anyone other than an EPI Authorized Service Center Improper environment Excessive or inadequate heating or air conditioning or electrical power failures, surges, or other irregularities
  This three-year limited warranty does not cover any of the product’s firmware or hardware that you or any third party have modified or altered; you bear the sole responsibility and liability for any such modification or alteration.
  78
  r

ALL EXPRESS AND IMPLIED WARRANTIES FOR THIS PRODUCT (INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE) ARE LIMITED IN DURATION TO A PERIOD OF THREE (3) YEARS FOR PARTS AND LABOR AND ONE (1) YEAR FOR CRT TUBE OR LCD PANEL FROM THE ORIGINAL DATE OF CONSUMER PURCHASE. NO WARRANTIES (EITHER EXPRESSED OR IMPLIED) APPLY AFTER THIS PERIOD. IN THE UNITED STATES OF AMERICA, SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATIONS MAY NOT APPLY TO YOU.
EPI OBLIGATIONS AND YOUR REMEDIES HEREUNDER ARE SOLELY AND EXCLUSIVELY AS STATED HERE. EPI’ LIABILITY, WHETHER BASED ON CONTRACT, TORT. WARRANTY, STRICT LIABILITY, OR OTHER THEORY, SHALL NOT EXCEED THE PRICE OF THE INDIVIDUAL UNIT WHOSE DEFECT OR DAMAGE IS THE BASIS OF THE CLAIM. IN NO EVENT SHALL ENVISION PERIPHERALS, INC. BE LIABLE FOR ANY LOSS OF PROFITS, LOSS OF USE OR FACILITIES OR EQUIPMENT OR OTHER INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGE. IN THE UNITED STATES OF AMERICA, SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES. SO THE ABOVE LIMITATION MAY NOT APPLY TO YOU. ALTHOUGH THIS LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS. YOU MAY HAVE OTHER RIGHTS WHICH MAY VARY FROM STATE TO STATE.
In the United States of America, this limited warranty is only valid for Products purchased in the Continental United States, Alaska, and Hawaii. Outside the United States of America, this limited warranty is only valid for Products purchased in Canada.
Information in this document is subject to change without notice. For more details, please visit:
USA: http://us.aoc.com/support/warranty ARGENTINA: http://ar.aoc.com/support/warranty BOLIVIA: http://bo.aoc.com/support/warranty CHILE: http://cl.aoc.com/support/warranty COLOMBIA: http://co.aoc.com/warranty COSTA RICA: http://cr.aoc.com/support/warranty DOCAN REPUBLIC: http://do.aoc.com/support/warranty ECUADOR: http://ec.aoc.com/support/warranty EL SALVADOR: http://sv.aoc.com/support/warranty GUATEMALA: http://gt.aoc.com/support/warranty HONDURAS: http://hn.aoc.com/support/warranty NICARAGUA: http://ni.aoc.com/support/warranty PANAMA: http://pa.aoc.com/support/warranty PARAGUAY: http://py.aoc.com/support/warranty PERU: http://pe.aoc.com/support/warranty URUGUAY: http://pe.aoc.com/warranty VENEZUELA: http://ve.aoc.com/support/warranty IF COUNTRY NOT LISTED: http://latin.aoc.com/warranty

References

• Homepage | AOC Monitors
• Homepage | AOC Monitors
• Homepage | AOC Monitors
• MHL® – Expand Your World
• Manual-Hub.com – Free PDF manuals!

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>