Laifen SE High Speed Hair Dryer User Guide

Laifen SE High-Speed Hair Dryer
Quick Start GuideC

Function Description

Power On/Off and Speed Setting
Push up or down to quickly switch between two speed settings.

Temperature Setting

• Press to switch between:

Long press to switch to:

Activating the function:
When the appliance is in use, long press the temperature setting button for 1 second to activate the Temperature Cycling Mode. (there are 2 levels of hot air).

Deactivating the function:

1. Press the temperature setting button once to deactivate it.
2. Turn off the appliance to deactivate the function.

*The illustrations of products, accessories, user interfaces, etc., in the manual are for reference purposes only and are schematic diagrams. Due to product updates and upgrades, there may be slight differences between the actual product and the schematic  diagrams. Please refer to the actual product for accuracy.

Nozzle Usage **

**

Gently place the nozzle on the head of the appliance.
When you hear a “click” sound, it indicates that the nozzle has been securely attached.

Direct the appliance at a specific section of your hair and adjust the nozzle’s position to achieve your desired drying or styling.

Drying Instructions

| Pat your hair dry with a towel to remove excess moisture.
---|---
| Maintain an appropriate distance between the appliance and your hair.
| Start drying from the roots and gradually move towards the ends of the hair to ensure even heating and  airflow distribution.
| You can use your hands or a comb to assist in drying or styling the hair.

Cleaning and Maintenance

| Before cleaning the filter, please ensure that the appliance is off and the power cord has been unplugged.
*The filter needs regular cleaning and maintenance to prevent blockage and ensure smooth airflow.
---|---
| The intake filter is attached using magnets. Grasp the handle and pull the intake filter down to remove it from the handle.
| Use a dry lint-free cloth, soft brush, toothbrush, or similar tool to remove any residue from the intake filter and the surface of the stainless  steel filter.
Do not use water to clean the stainless steel filter, as it may cause malfunctions.
| After cleaning, align the intake filter with the handle slot and insert it. When you hear a “click” sound, it indicates that the magnet has been  securely attached, and the installation is complete.

Common Faults and Troubleshooting

Check if the power is properly connected
2. Check the circuit breaker, ensure the reset button is in the normal pressed  state.
3. If the issue persists, contact support (see below).
Motor doesn’t start; blinking blue light| Overheating protection activated| 1. Power off, shut down, and wait 5-10 minutes before restarting.
2. If the issue still cannot be resolved, contact support (see below).
Motor doesn’t start; blinking yellow light| Protection mode activated due to internal  component issues| 1. Power off, shut down, and wait 5-10 minutes before restarting.
2. If the issue still cannot be resolved, contact support (see below).
Motor doesn’t start; blinking red light| Inlet or outlet blocked| 1. Please clean the intake filter and exhaust vent, ensuring there are no  blockages, then restart.
2. If the issue still cannot be resolved, contact support (see below).
Ring light not working, but the motor starts  normally| Faulty ring light circuit board| Contact support for assistance (see below)
Starts normally, but air speed and temperature  cannot be changed| Damaged button switch| Contact support for assistance (see below)
Heating element turns red| Main control board malfunction or inlet/outlet blockage| 1. Please clean the intake filter and exhaust vent, ensuring there are no  blockages, then restart.
2. If the issue still cannot be resolved, contact support (see below).
Power cord or plug overheating| Damaged power cord or loose plug| 1. Try using a different outlet, ensuring the plug is correctly connected.
2. If any abnormalities are found, please contact support (see below).
Burnt smell during use| Internal components damaged| Contact support for assistance (see below)
Insufficient heat in hot air mode| Inlet blocked| 1. Please clean the intake filter and exhaust vent, ensuring there are no  blockages, then restart.
2. If the issue still cannot be resolved, contact support (see below).

Laifen Customer Support : csteam@laifentech.com

Get Professional Assistance from Laifen
Contact US :
csteam@laifentech.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>