iMartine PANTONE 333 C Robot Vacuum and Mop Cleaner User Guide

iMartine PANTONE 333 C Robot Vacuum and Mop Cleaner

Please read this manual in detail before using and keep it properly

Service Guarantee

Thank you for your purchase. Our promise:

1. Activate the 1-year warranty by scanning the QR code below.
2. Please feel free to contact us if you need tech- support via our after-sales email below.

E-mail: support@imartine.com

IOS

1. I0S system device user. please slide to this page and click this icon to enter the scan code page.
2. Open the “Camera” app from the home screen page, control center page or locking screen page. Then select the back camera and scan the QR code. The device will recognizethe QR code and display a notification. Tap the notification to open the link to get youre-warranty registered.
3. Twitter and other apps which has the scar function can scan this QR code as well.

ANDROID

1. Find the icon for scanning the QR code in the system browser, enterithe scan code page
2. Twitter and other apps which has the scan function can scan this QR code as well.

Important Safety Instruction

To reduce the risk of injury or damage, keep these safety precautions in mind when setting up, using and maintaining your robot:

• Read all safety and operating instructions before operating your robot.

• Retain the safety and operating instructions for future refrence.

• Heed all warnings on your robot, battery,charging dock and in the owner’s manual.

• Follow all operating and use instructions.

• The external flexible cable or cord of the power supply unit can’t be replaced; If the cord or plug is damaged, the power supply unit shall be disposed of.

• This product is designed to be plugged into a standard outlet only. The product may not be used with any type of power converter. Use of power converters will immediately void the warranty.

• CAUTION : Only charge one of the following robot batteries: maximum 14.4V, max 2600mAh Ni-MH or maximum 2600mAh Li-ion battery.
  Another type of batteries may burst causing injury. Always contact customer care for the correct replacement of your battery.

• Always charge and remove the battery from your robot and accessories before long-term storage or transportation.

• The battery must be removed from this device before this device is disposed of. To remove the battery from this device, rst remove the screws on the bottom, then remove
  the main PCB and unscrew the battery cover using a screwdriver. Remove the battery by disconnecting the quick connector.

• WARNING Chemical Exposure: If the battery pack is leaking, do not allow the liquid to come in contact with skin or eyes. If contact has been made, wash the aected area with copious amounts of water and seek medical advice. Place the battery (the used battery pack included when the robot wil be disposed) in a sealed plastic bag and dispose of safely according to local environmental I regulations.

• WARNING Fire or Explosion Hazard: Do not crush or dismantle battery packs. Do not heat or place the battery pack near any heat source or direct sunlight. Do not incinerate or short-circuit the battery pack. Do not subject batteries to mechanical shock.

• Contact your local waste management authority for battery recycling and disposal regulations in your area.

• Your robot is not a toy. Do not sit or stand on robot. Children and pets should be supervised when your robot is operating.

• Robot is for indoor use only.

• Do not use non-rechargeable batteries. Use only the rechargeable battery supplied with the product. For replacement, purchase identical probot battery or contact probot customer care for alternative battery options.

• Store and operate robot in room temperature environments only.

• Do not spray or pour liquids on your robot.

• Do not use any other power supply cord. For replacement cords, please contact customer care to ensure proper selection of country specie power supply cord.

• Do not use robot to pick up sharp objects, glass, or anything that is burning or smoking.

• Do not immerse the battery pack in any liquid.

• Do not use robot to pick up spills of water bleach, paint, or other chemicals, or anything wet.

• Before using robot, pick up objects like clothing, loose papers, pull cords for blinds or curtains, power cords, and any fragile objects. If robot passes over a power cord and drags it, there is a chance an object could be pulled o a table or shelf.

• If the room to be cleaned contains a balcony, a physical barrier should be used to prevent access to the balcony and ensure safe operation.

• Do not place anything on top of your robot.

• Be aware that the robot moves on its own. Take care when walking in the area that the robot is operating in to avoid stepping on it.

• Do not operate the robot in areas with exposed electrical outlets in the floors.

• Do not use this device on an unnished, unsealed, waxed or rough floors. It may result in damage to the floor and this device. Use only on hard floor surfaces or low pile carpet.

• This device has been designed to be used on floors without scratching them. We still recommend that you test this device on a small area of the room to be cleaned to ensure no scratches are made before cleaning the whole room.

Battery and Charging/Information

Lithium-ion Battery
Important: Lithium-ion batteries and products that contain lithium-ion are subject to stringent transportation regulations. If you need to ship this product {with the battery included) for service, travel or any other reason, you must comply with the following shipping instructions:

• Remove the lithium-ion battery from the product.
• Place a piece of tape over the battery’s metal charging contacts.
• Reinstall the battery {with the tape on it) in the product and secure the battery door.
• Package the product in its original packaging or in your own packaging that prevents any movement during transportation.
• Ship via ground transportation only {no air shipping).

Battery Storage
If storing robot on the charging dock, remove the battery first then store robot and the battery in a cool, dry place

The symbol on the product or its packaging indicates:
Do not dispose of electrical appliances as unsorted municipal waste, use separate collection facilities. Contact your local authority for information regarding the collection systems availabe. If electrical appliances are disposed of in landlls or dumps hazardous substances can leak into the groundwater and get into the food chain, damaging your health and well-being. Please contact your local or regional waste authority for more information on collection, reuse and recycling programs.

PRODUCT INTRODUCTION

Robot Vacuum Cleaner

Accessories List

Charging Base

Remote Control

Reminder:
Install a pair of AAA batteries before using the remote control in first time. Ensure that the polarity of the battery is installed correctly; When using the remote control, please aim it at the vacuum, and the effective distance is 0-5 meters.

LED Indicators

APP CONNECTION

1. Search “Vi life” in the mobile app store/google play/Apple app store to download the APP, or scan the QR code to download.
2. Register and log in.
3. This robot vacuum only supports 2.4G Hz WiFi. Please confirm whether the current WiFi is 2.4G Hz WiFi. You can search the teaching method of conventional router settings in the FAQ on the next page to try to query or change it to 2.4G Hz WiFi. If the operation is not successful, please contact our customer service team ( support@imartine.com )
4. Click “Add device”,
5. Select the imartine-G1061. Note that if Bluetooth is not turned on, you will be prompted to turn on Bluetooth.
6. Press and hold the button to turn the vacuum on, hearing “The vacuum has started” and then enter the next step.
7. Press and hold the and for 3s at the same time, hearing “Network Connecting”, and then enter the next step.
8. After completing step 6 and 7, the WiFi indicator flashes, and click next
9. Click to add device.
10. Confirm that it is a 2.4G network, enter the WiFi name and password, and then click “Next”.
11. When it is completed, please click “Next”.
12. The equipment is added.

You can find this page if any questions for connecting to the network or other questions.
You can refer to FAQs or search for any problems. Please feel free to contact us if any suggestions.
For example, how to switch SgHz WIFI to 2.4gHz WIFI?

If you want to add real-time weather, please set it manually in APP
The real-time weather function is optional, you can choose to add it or not .

• The final effect af the real­time weather function
• Click “Me” and then find “Home Management”.
• Click “Create a home”
• Name your home and choose location, then click “Save”.
• Return to the homepage, click on the upper left corner to select “My home” that you created before.

USER INSTRUCTION

Quick Start

1. Plug in the charging dock, and take the rest wire into the trunking at the bottom of charging dock.
   Note: If you don’t put the rest wire into the trunking, which may stuck the robot while charging or cleaning

2. Charging Dock Position

3. Place the charging dock on a hard, level surface and against a wall.

  * 2 meter (6.5 feets) in front of the charging dock.
  * 1 meter (2.3 feets) on both sides of the charging dock.
2. Connect the round connector of the adapter into the power socket on the charging dock and the other end into a wall outlet![iMartine-PANTONE-333 C-Robot-Vacuum-and-Mop-Cleaner-FIG- \(15\)](https://manuals.plus/wp-content/uploads/2023/05/iMartine-PANTONE-333-C-Robot-Vacuum-and-Mop-Cleaner-FIG-15.png)  

Always keep the charging dock plugged in, otherwise robot will not automatically return to it.

3. Install side brushes, attach side brushes to the bottom of robot by pressing a brush into each slot .

4. Turn on the main power switch on the bottom of robot.

5. Activate the Robot
   Place robot onto the charging dock, making sure the metal charging contacts on the charging dock match up with those underneath the robot. If match successfully, you will hear a series of tones once the O power button illuminates, robot is ready for use.

6. DJ Start Cleaning Cycle

7. Press the power button once to wake up the robot.

8. Press the power button again to start a cleaning cycle.

9. If its battery gets low before finishing a cleaning cyde, robot will return to the charging dock to recharge.

10. If the charaing dock is inaccessible, robot will not be able to recharge, it will return to its starting location and the cleaning cycle will end, please place the robot manually on charging dock for charging. (Refer Activate the robot)

11. Pause

12. To pause the robot during a cleaning cycle press the button or press the ►II button on remote control.

13. To resume the cleaning cycle, press button again.

14. To send robot back to The charging dock, press button.

15. Power OFF

16. To end the cleaning cycle and put robot in standby mode, press and hold C) button until robot indicator is off.

Cleaning Modes

Auto Cleaning

• Press or use the remote control or the mobile app to start auto cleaning.
• If the battery is low before the cleaning is completed, the vacuum will return to the charging base for charging.

Reminder: If the charging base cannot be found during the recharging process, the red light will flash and beep four times. Please manually put the vacuum into the charging base for charging.

Spot Cleaning

When you select spot cleaning, vacuum intensely cleans a localized area by spiraling outward about 5 feet(1.5 meter) in diameter and then spiraling inward to where it started. The vacuum’suction will increase to provide the best cleaning. You can place vacuum on top of the localized debris and press ® on the remote control.

Edge Cleaning

Press in remote control to clean the place along the wall and around furniture legs.

PRODUCT MAINTENANCE

To ensure the span life and best cleaning performance, please refer to the following instructions for cleaning and maintenance of vacuum’s accessories.

Recommended cleaning/Replacement frequency

Emptying Robot’s Bin

1. Press bin release button to remove the bin.
2. Open bin’s door to empty it.

Cleaning Robot’s Filter

1. Remove filter by grasping the white tab.
2. Shake off the garbage on the filter.

Cleaning Robot ‘s Roller Brush, Side Brush, Driving Wheels and Sensors.

1. Take out the roller brush, clean the vacuuming aisle by a cloth.
2. Pull out the driving wheel, then clean the driving wheel with the cleaning tool.
3. Clean the roller brush. Cut down the hair winded in the roller brush with the provided cleaning tool’s knife
4. Remove the side brush, use a cloth to remove the dust from the brush.
5. Use the cleaning brush to clean the dust on the sensor to ensure the best performance.

Light Indicator & Beeps Error

Light Indicator Prompt

• Vacuum status                                                              Light
• Charging                                                                      Orange light breathes
• Charging completed                                                   Solid green light
• Vacuum error                                                                Solid/flashing red light
• Low battery                                                                   Flashing red light
• Cleaning                                                                       Solid green light

Beeps Error

Any error that occurs during operation will be notied by the robot through light status and beeps,the instruction as below:

Beeps with Flashing Red Light:

Beeps with Solid Red Light:

Tips
If the above solutions can not solve the problem, please try the following:

1. turn on the power switch at the bottom of the robot and restart.
2. If the problem cannot be solved by restarting, please contact the after-sales email: support@imartine.com

Troubleshooting

again.
Can’t control vacuum

through APP

| ****

Network signal is not in good condition.

| ****

Please exit the APP and re-enter.

Decreased cleaning capacity

| ****

a.  Thedust bin is full.

b.  Theniter gapis blocked.

c.  The roller brush is entangled by sundries.

d.  The roller brush or side brush is worn.

| a. Please clean the dust bin in time. Remove the HEPA tilter before washing the dust bin.

b. Please shake off the ash adsorbed on the HEPA niter and tap the sponge. Or replace the niter.

c. Please clean the roller brush in time.

d. Please replace the roller brush or side brush in time.

Schedule cleaning failed

| ****

a. The power is less than 20%.

b. The mobile phone time is inconsistent with the local standard time.

c. The vacuum still has unfmished cleaning tasks to perform .

d. The cleaning switch in the timing is not turned on.

| a. Ensure that the vacuum is turned on and the power is more than 20%.

b.  Ensure that the mobile phone time is consistent with the local standard time.

c. Press the “ON” button on APP to cancel the task to be executed, and then add schedule.

d. Open the scheduled cleaning switch in APP and make an

appointment for cleaning.

Difficult to clean a long­ haired carpet| ****

Carpet with hair thickness over 20mm will be hard to clean.

| ****

Please clean carpets with hair thickness under 20mm.

Water into the vacuum

| ****

a.  When mopping the floor, the water flows too much and the mopping time is too long.

b.  There is too much ponding water on the ground, which is sucked into the vacuum when cleaning or mopping.

| ****

a. If suck a large amount of water, please take out the dust bin and roller brush, wipe the water stains, put the machine in a ventilated place to dry, and then reinstall it for use. Normally clean and mop which will not affect the use even if suck a small amount of water.

b.  Remove the niter on the dust bin, do not wash it with water, use brush to clean the water and dirt ontheniter, and then put it back into useafter drying it all; If theniter is completely wet, please replace it.

Loud

| a. The noise generated automatically during cleaning.

b. Quiet mode makes little noise, strong mode makes much more noise.

| a. It is normal to make noise during operation .

b.  Select the quiet mode.

No sound| The horn is silent.| Please check whether the horn hole is blocked or not.

Vacuum keeps moving

backward

| ****

a. Thebumper is stuck by sundries.

b. The bumper is misplaced.

c. The floor sensor is dirty.

d. The driving wheel is twined by sundries.

| ****

a.Pat the bumper gently to shake down the sundries.

b. Please disassemble and reassemble the bumper, the bumper can be used normally after resetting.

c. Clean the floor sensor.

d. Clear the twined sundries on the universal wheel.

Stop when crossing obstacles| Obstacle height ;,,2omm.| The vacuum can only work normally with the obstacle height

<20mm.

Vacuum dropped| The space height ,;,6Qmm.| The anti-drop function is not available in a space height lower than 60mm.

vacuum hits the

wall/furniture

| ****

It is normal for the vacuum to slightly collide in order to clean the

corner area.

| ****

a. There is an anti-collision bumper on the front, please rest assured to use it.

b.  Please well collect your valuable objects.

Stuck under the furniture

| ****

There isn’t enough space under the furniture.

| ****

Please ensure the height under the furniture is more than

the thickness of the vacuum.

Thedistance of manually moving back is short.| This is designed for avoiding the vacuum dropping from the backside. It’s normal status.| You can change the direction of vacuum through remote

control/ APP to right/left, andthen go ahead.

Spins in circle/Side wheel

is abnormal

| ****

The wheels were twined by sundries and then stuck.

| ****

Please use the supplied cleaning brush to clear the sundries.

Loud

| ****

The side brush is deformed

| Please soak the side brush into 80-90°C hot water for about 20S to recover it.

Side brush dropped

| The side brush was not installed in place.| Press install the side brush in force until you heard a “click”

sound.

Map or route tilts

| ****

a. The charging base was not placed against the wall, or the vacuum didn’t start from the charging base.

b.There is too much debris near the vacuum starting place, which causes inaccurate reference coordinates.

| ****

a. Please ensure the charging base is back placed against the wall, and start the vacuum on the charging base.

b.  Please place the charging base in an open area.

Abnormal cleaning route

| ****

There are too many obstacles in the cleaning area.

| ****

Clear the unnecessary obstacles.

Can’t connect to Alexa/Google smart speaker| ****

Improper operation.

| Please read the network connection guide and user manual carefully. Need further help, please contact our customer service for support.

Other problems

| ****

Other unlisted problems.

| ****

Please contact our customer service for support.

E-mail: support@imartine.com
Warranty Web: imartine.warrantyhere.com
Official Web: www.imartine.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>