MASIGO 2AXURX5005 Dash Camera User Manual

MASIGO 2AXURX5005 Dash Camera

Product Information

Specifications

• FCC ID: 2AXURX5005

Product Usage Instructions

Antenna Installation

To ensure optimal performance, it is important to use only the supplied antenna.

Follow the steps below to install the antenna:

1. Locate the antenna port on the radiator body.
2. Gently screw the supplied antenna into the antenna port until it is securely attached.

Powering On the Radiator

Before using the radiator, make sure it is properly powered on:

1. Connect the power cable to the power input port on the radiator body.
2. Plug the other end of the power cable into a compatible power outlet.
3. Press the power button, usually located on the front panel of the radiator, to turn it on.

Adjusting Temperature Settings

To set and adjust the desired temperature on the radiator, follow these steps:

1. Locate the temperature control buttons on the radiator body.
2. Press the “+” button to increase the temperature or the “-” button to decrease it.
3. Continue pressing the buttons until you reach your desired temperature.

Safety Precautions

When using the radiator, it is important to keep the following safety precautions in mind:

• Do not touch the radiator with wet hands or while standing in water.
• Keep flammable materials away from the radiator.
• Ensure proper ventilation in the room where the radiator is being used.
• Do not cover the radiator or obstruct the airflow around it.
• Always unplug the radiator when not in use or before performing any maintenance.

Frequently Asked Questions (FAQ)

Q: Can I use a different antenna with the radiator?

• A: It is recommended to use only the supplied antenna to ensure optimal performance and FCC compliance.

Q: How do I clean the radiator?

• A: To clean the radiator, first, make sure it is unplugged and cooled down. Then, use a soft cloth or brush to gently remove any dust or debris from the surface. Avoid using water or any liquid cleaners on the radiator.

Q: Can I leave the radiator unattended?

• A: It is not recommended to leave the radiator unattended for long periods.
• Always ensure someone is present to monitor its operation and to follow safety precautions.

Safety Precautions And Notice

• Please read the instruction manual carefully before using the product to ensure safe and proper usage.
• Follow the precautions below to prevent injuries to yourself and others, or property damage.
• Keep the device away from extreme heat, cold, moisture, and dust.
• Do not use liquids or chemical cleaners for cleaning the device.
• Do not insert any objects into the device.
• Avoid exposing the device to direct sunlight for an extended period, as overheating will damage the device and shorten its lifespan.
• Do not operate the controls of this device while driving. Pull over in a safe area before attempting such operations.
• Do not place the device where it obstructs the driver’s field of vision while driving or in front of/above any airbag.
• Use only the car charger supplied with your device. The use of any other types of chargers may damage the device and void the manufacturer’s warranty.
• Do not disassemble, modify, remanufacture, puncture, or damage the device or batteries.
• Do not attempt to remove or replace the non-user-replaceable battery.
• Do not expose the device to fire, explosion, or other hazards, rain, or water.
• Do not attempt to disassemble, repair, or modify the device. Doing so will void the product warranty and damage the device.
• Dash cam usage is prohibited or restricted in some countries or states in compliance with the country’s strict privacy laws. Please adhere to local laws.

FCC Statement

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference,
2. this device must accept any interference received, including interference that may cause undesired operation.

Note:
This equipment has been tested and found to comply with the limits for a Class B digital device, according to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used under the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, it can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Box Content

• Front Camera
• Car Charger
• GPS 3M Adhesive Mount
• Rear Camera*
• Rear Camera Cable*
• User’s Manual (includes a static cling and a 3M adhesive tape)

Note:

• It is only available for dual channel dash cam.
• The rear camera cannot be operated on its own.
• Supplied accessories may vary by region.

Product Overview

1. Speaker:
   • Audio output
2. LED indicator:
   • Steady red   light: Power on
   • Flash red light: Recording
   • Steady blue light: The camera is connected to a power source
   • Blue light off: Not connected to a power source
3. Function buttons:
   • There are 4 function buttons to operate the camera in different ways.

At Recording Screen

1. Open the menu, and go through the video menu, system menu, and playback menu.
2. Switch PIP display
3. Turn off/on the microphone. Hold and press to enable Wi-Fi.
4. File protected button.

At Menu Screen

1. Back to the previous page.
2. Up button: Navigate to the previous option.
3. Down button: Navigate to the next option.
4. OK

At Video Playback Screen

1. Press once to stop the video, and press twice to the previous menu page.
2. Press once to stop the video, press twice to the previous clip; Press and hold to backward the current video at 2X speed, and release it to playback the current clip.
3. Press once to pause the video, press twice to the next clip; Press and hold to forward the video at 2X speed, and release it to playback the current clip.
4. Playback or pause the video.
5. Memory card slot:
   • Insert a micro SD card for recording.
6. Video in port:
   • Connects to rearview camera.
7. Microphone:
   • Records audio.
8. Mounting slot:
   • Attached is the suction cup mount.
9. Reset:
   • Press to force the camera to restart.
10. Power button:
    • Hold to turn the camera on/off; Press once to turn off/on the screen, and the camera is on standby mode.
    • X5003 features a supercapacitor and must be connected to a power source for operation.
11. Mini-USB power port:
    • Plug the power cable into the USB port.

System icon

Getting started

• Inserting memory card
• A micro SD memory card is required to insert into the camera before starting recording.
• Your micro SD card should have a minimum speed rating of Class 10 and at least a U3 rating.
• Be sure to format the memory card with the device before initial use.
• To remove a memory card, turn off the camera and press the memory card to pop it out of the slot.

Note:

• Removing the memory card while the camera is on can result in a loss of data.
• To maintain the card’s full-speed performance, preserve its storage capacity, and reduce the risk of storage errors, you should regularly format your micro SD card.
• Don’t forget to back up your memory card before reformatting it.
• MASIGO does not guarantee compatibility with memory cards from all manufacturers.

Recording Time

Installation in your vehicle

1. Clean your windshield:
   • Cleaning the inside and outside of the windshield with window cleaner before applying the adhesive.
2. Mount the dash cam:
   • Mount the dash cam in or near the middle of your vehicle’s windscreen and just below, behind the rearview mirror, don’t block the driver’s view of the road ahead.
   • Applying the static cling to the windshield of your car is highly recommended. Make sure the clear film is secure by pressing it down on the windshield.
   • The clear film should be flat and rid of any air bubbles. Apply your camera’s adhesive mount on top of the film to finish.
   • To remove the mount, easily peel away the removable film.
3. Connect the power cable:
   • Connect the car charger to your dash cam and vehicle power outlet.
   • Route wires behind the vehicle trim along the windshield, doorframe, or dash.
4. Adjust the lens angle
   • Rotate the adjusting knob, Loosen counterclockwise to adjust the direction of the dash cam, and then tighten it clockwise after adjustment.
   • Recommend the ratio of the ground to the sky in the screen is about 6: 4.

Basic Operation

Turn on/off the camera

• Automatically
  • The camera will automatically power on and start recording once receives power.
• Manually
  • Press and hold the power button for 3 seconds to turn on/off the camera.

Select language, time zone, date time, and speed unit

• * Go through the settings below for the first-time setup to select language, Time Zone, date time, and Speed unit.

• Select language
  • Press the up and down button to select the language, and press the OK button” OK “to the next setting.
• Select Time Zone
  • Press the up and down button to select your current time zone from the list, which will allow Daylight Savings time to be adjusted. Then press OKbutton “OK “to the next setting.
• Set Time and Date
  • Press the up and down button to set the current time and date, and press the OK button “OK “to the next number setting and exist.
• Select speed unit
  • Press the up and down button to display the speed in km/h or MPH

Video Recording

Continuous recording

• The camera will automatically turn on and start continuous recording after connecting to the car charger.
• Or manually turn on the camera by pressing the Power button
• In continuous recording mode, videos are recorded in several segments and saved in the “Normal” folder of the micro SD card.
• The default setting is in the 1-minute’ segment, you can change the recording length in the Video Menu Setting.

Incident recording

• During continuous recording, when the camera detects possible accidental collisions, a 1 minute/3 minute video footage (depending on the loop recording selected length) is locked from being overwritten and saved in the “Event video” folder automatically. You can adjust the G-sensor level in the Video Menu setting, the default is low.

Manual recording

• When the camera is on recording, press the file protected button to lock a 1 minute/3 minute video footage from being overwritten and saved in the “Event video” folder.
• At the same time, a snapshot is saved in the “Event photo” folder automatically.

Parking surveillance

• Parking surveillance requires a constant power supply from the car battery.
• A hardwire cable built with battery discharge prevention is recommended.
• The camera will automatically enter parking mode when the car stops moving for over 10 minutes.
• If the vehicle is subjected to a collision, the camera automatically records a 1 minute/3 minute video footage and saves it in the “Event video” folder.
• The default is disabled. Enable the Parking Surveillance function in the Video Menu setting.
• Press the MENU button once to enter the Video Menu setting.
• Press down button to scroll down the menu list and select Parking Surveillance.
• Press the “OK “ button and select” On” to enable the parking recording function.
• The camera will return to continuous recording when the detected movement is subsequently.

Playback Mode

• Press the Menu button three times to enter the Playback Menu page, and press the up and down button to scroll down the folder. Press the OK button to review the files.
• Note: The camera stops recording while viewing videos and photos.

Connect to Wi-Fi

• Search and download MASIGO Dashcam Viewer(Worldwide) in the Google Play Store or Apple App Store.
• You can view and download recorded videos, change camera settings, and update the camera firmware on your smartphone.

Minimum requirements for running this application

• Android 8.0 or higher
• iOS 8.0 or higher

Connect the camera to a smartphone

1. Press and hold the camera Wi-Fi button to enable the Wi-Fi hotspot.
2. On your smartphone, select the Wi-Fi network name same as displayed on the camera MASI GO XXXXX-XXXX, and enter the Wi-Fi password”12345678″.
3. Run MASI GO Dashcam Viewer
4. Tap Connect Dash Cam> Enter Dash cam> Connecting> Connected. Then camera is connected to your smartphone via Wi-Fi.
5. Tap Settings to change the camera settings on your smartphone.
6. Tap Playback to view and download recorded videos on your smartphone, and save videos to your phone’s album/pictures.

Camera Setting

Press the Menu button once to access the Menu setting, use the up and down button to scroll down the function, and press the OK  button to enter the options screen.

30/ 1080P60+1080P60
Video Format| MP4/TS
Video Length| 1 Minute/3 Minutes
Exposure Value- Front Exposure Value- Rear| +3/+2/+1/0(auto)/-1/-2/-3
Microphone| On/Off
G Sensor| High/Medium/Low/Off
Plate Stamp| On/Off
Parking Surveillance| On/Off
Rotate Display-Front| On/Off
Rotate Display-Rear| On/Off
Mirror Display-Rear| On/Off

Note: You can also configure the camera settings via the MASIGO Viewer APP on your smartphone.

Playback on computer

• Download and install the VLC media player to play the videos on your computer.
• Remove the micro SD card from the camera, insert it into the micro SD card adapter, and connect it to your computer.
• Use the VLC media player to play videos on your computer.

Warranty Terms

• Thank you for purchasing the MASIGO dash cam. Should your product require warranty service, please contact us directly to determine the problem and the most appropriate solution for you. See details below MASI AUTO CO., LTD
• 7F.-10, No.9, Sec.2, Nankan Rd., Luzhu Dist., Taoyuan City 338, Taiwan www.masigo.net
• Email: service@masiauto.com
• Facebook: @masigodashcam
• MASIGO product is guaranteed against defects in materials and workmanship under normal use for one (1) year from the date of purchase Warranty Period
• During the Warranty Period, MASI AUTO will repair or replace, at no charge, products or parts of a product that proves defective because of improper material or workmanship, under normal use and maintenance.

This Limited Warranty does not cover any problem that is caused by:

• Damage caused by misuse including but not limited to failure to use the product for its normal purpose or according to the user instructions or use of the proper use and maintenance, and to installation or use of product inconsistent with the safety standards in force in the country where it is used.
• Damage caused by accidents including but not limited to lightning, water, fire, misuse, or neglect.
• Defacing, illegibility, or removal of the model or serial number on the product.
• Damage resulting from repairs or adjustments that have been conducted by unauthorized service organizations or persons.
• Defects in any system into which the product is incorporated or with which it is used.

Disclaimer

• The material in this manual is for informational purposes only.
• MASI AUTO reserves the right to change or improve its products and to make changes in the content of this manual without obligation to notify any person or organization of such changes or improvements.
• Go to www.masigo.net for current updates and supplemental information concerning the use of this product.
• MASI AUTO shall not be liable for any damages, including without limitation, direct, incidental, consequential, indirect or punitive damages, arising out of access to, or any errors or omissions in the content thereof.

FCC

This device complies with part 15 of the FCC Rules. Operation is subject to the condition that this device does not cause harmful interference

1. this device may not cause harmful interference,
2. this device must accept any interference received, including interference that may cause undesired operation.

Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, under Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used per the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

To maintain compliance with FCC’s RF Exposure guidelines, This equipment should be installed and operated with a minimum distance between 20cm of the radiator and your body:
Use only the supplied antenna.
FCC ID: 2AXURX5005

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>