Hidoes HD-C2 Foldable Electric Bike for Adults Instruction Manual

Hidoes HD-C2 Foldable Electric Bike for Adults

Specifications

• Model: HD-C2
• Type: Electric Bicycle

Product Folding and Parts Display

1. Remove the packaging and place the ebike on flat ground.
2. Unfold the frame by closing the folding part in the direction of the arrow. Pull up the folding handle and close it.

Assemble the Whole Unit

1. Pull the folding handle in the direction of the arrow.

2. Open the folding riser telescopic adjustment buckle. Insert the telescopic vertical pipe in the direction of the arrow, making sure to cross the safety wire.

3. Adjust the required height of the telescopic vertical pipe and press the adjustment buckle in the direction of the arrow.
   Note: If the adjustment buckle is too tight or too loose, please adjust the screw at position 3 accordingly.

4. Erect and close the folding riser in the direction of the arrow. After confirming the quick disassembly and insertion, lift the pull rod and wrench in the direction of the arrow.

5. If the folding wrench is too tight or too loose, please adjust the screw at position 1 accordingly.

Install the Saddle

1. Pull the quick release lever of the seat tube.
2. Insert the seat tube and adjust it to a proper height. Lock the quick release handle in place.

Note: Please adjust the screw at position 1 if the folding handle is too tight or too loose.

Parts Installation

• Front Reflector Installation Guide: Slide the front reflector bracket into the corresponding position of the handlebars. Tighten the screw with a Phillips screwdriver.
• Bell Installation: Insert the bell into the corresponding position on the handlebar. Use a Phillips screwdriver to tighten the screw.
• Wheel Reflector Installation Guide: Place the wheel reflector on the reserved position of the wheel hub. Use a Phillips screwdriver to tighten screws 1 and 2. The operating instructions for front and rear wheel reflectors are the same.

Fixing the Rear Fender Support Rod

1. Use the 4# Allen wrench in the 16 in 1 tool to remove the pre-installed screws and gaskets of the fender support rods on both sides of the frame.
2. Put the support rod through the fixing screw and tighten it in the corresponding screw holes on both sides of the frame with a 4# Allen wrench.

Install the Pedal

The L marked on the pedal shaft refers to the left pedal. First, counterclockwise rotate the pedal shaft that enters the crank by hand, and tighten it with a 15# open-ended wrench counterclockwise.

The R marked on the pedal shaft refers to the right pedal. First, clockwise rotate the pedal shaft that enters the crank by hand, and tighten it with a 15# open-ended wrench clockwise.

Take Out the Battery

1. Pull up the handle at the bottom of the saddle.
2. Turn the seat tube upward.
3. Turn the key to PUSH for removing the battery.
4. Pick up the battery handle and take out the battery.

Installing the Battery

1. Align the battery to the battery track.
2. Insert the battery to the bottom, making sure it fully contacts with the discharge plug.

Frequently Asked Questions

Q: How do I adjust the folding handle if it’s too tight or too loose?

A: You can adjust the screw at position 1 accordingly.

Q: How do I adjust the adjustment buckle if it’s too tight or too loose?

A: You can adjust the screw at position 3 accordingly.

Q: How do I adjust the folding wrench if it’s too tight or too loose?

A: You can adjust the screw at position 1 accordingly.

Q: How do I adjust the folding handle if it’s too tight or too loose?

A: You can adjust the screw at position 1 accordingly.

Product folding and parts display

Assemble the whole unit

1. Remove the packaging, place the ebikeon flat ground, then unfold the frame.
2. Close the folding part in the direction of the arrow, Pull up the folding handle and close it.

3. Pull the folding handle in the direction of the arrow.

4. Open the folding riser telescopic adjustment buckle,insert the telescopic vertical pipe in the direction of the arrow,and be sure to cross the safety wire.
5. Insert the telescopic vertical pipe, adjust the required height, and press the adjustment buckle in the direction of the arrow in the figure.
   Note: If the adjustment buckle is too tight to move or too loose, please adjust the screw at position “3” appropriately.

6. Erect and close the folding riser in the direction of the arrow in the figure.
7. After confirming the quick disassembly and insertion, lift the pull rod and wrench in the direction of the arrow in the figure.
8. If the folding wrench is too tight or too loose, please adjust the screw at position “1” appropriately.

Install the saddle

1. Pull the quick release lever of seat tube.
2. Insert the seat tube, adjust it to a proper height, and lock the quick release handle in the direction.
   Note: Please adjust the screw at “1” If the folding handle is too tight or too loose.

Parts installation

1. Front Reflector Installation Guide: Slide the front reflector bracket intothecorresponding position of the handlebars, tighten the screw with a Phillips screwdriver.
2. Bell Installation: Insert the bell into the corresponding position on the handlebar. Use a Phillips screwdriver to tighten the screw.

3. Installation Guide for wheel reflector：Place the wheel reflector on the reserved position of the wheel hub, use a Phillips screwdriver to tighten two screws “1” and “2”.
   The operating instructions for front and rear wheel reflectors are the same.

Fixing the rear fender support rod

1. Use the 4 # Allen wrench in the 16 in 1 tool to remove the pre-installed screws and gaskets of the fender support rods on both sides of the frame.
2. Put the support rod through the fixing screw and tighten it in the corresponding screw holes on both sides of the frame with a 4 # Allen wrench.

Install the pedal

1. The “L” marked on the pedal shaft refers to the left pedal.
   First, counterclockwise rotate the pedal shaft that enters the crank by hand, and tighten it with a 15# open-ended wrench counterclockwise.

2. The “R” marked on the pedal shaft refers to the right pedal.
   First, clockwise rotate the pedal shaft that enters the crank by hand, and tighten it with a 15# open-ended wrench clockwise.

Take out the battery

1. Pull up the handle at the bottom of the saddle.
2. Turn the seat tube upward.
3. Turn the key to “PUSH” for removing the battery.
4. Pick up the battery handle and take out the battery.

Installing the battery

5. Align the battery to the battery track.
6. Insert the battery to the bottom, make it fully contact with the discharge plug.
7. Place the battery in a downward direction.
8. Press the saddle down until it fully engages with the seat tube.

Switch on/off

1. Insert the key into the keyhole at figure 1, turn the key to the “OFF” gear right to turn the key to the “ON” gear.
2. Press the switch on the meter at figure 2. Then you can turn on the machine.
3. Insert the key and turn the key to the “ON” position by turning it to the right of the “OFF” position.
4. Switch on: Press the button shown in the picture.

Front basket for choice

• Align the basket hole with the tube, install four screws into the aligned holes, and tighten them.
• With Front Basket

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>