dBTechnologies IS210T Active Subwoofers User Guide
- June 17, 2024
- dBTechnologies
Table of Contents
dBTechnologies IS210T Active Subwoofers User Guide
MAIN FEATURES
- Impressive sound pressure
- Rotatable horn
- Quick installation
- Easy handling and transport
- Stack or flyable use
PACKAGE CONTENTS
The box contains: N°1 IS210T loudspeaker This quick start and warranty documentation
DESCRIPTION
IS210T is the new dB Technologies 2-way passive speaker for professional use. It is equipped with a compression driver (HF exit: 1.4”, 2.4 voice coil) and two 10” neodymium woofers (2.4” voice coil). The coverage pattern is 90° (H) x 40° (V). The horn is rotatable and the mechanical design allows an easy, accurate and quick installation for stand or flyable use thanks to the optional brackets
ACCESSORIES
-
HB-3X10
bracket for flyable use
-
VB-3X10
bracket for stacked/ flyable use -
SP-IS
speakON® panel
DIMENSIONS
TECHNICAL SPECIFICATIONS
| Speaker Type | 2 Way Passive Loudspeaker |
|---|---|
| Protection against solid objects and liquids (IP): | 55 |
| Frequency Response [-6dB] | 60 Hz – 17.8 kHz |
| Usable Band with [-10dB] | 56 Hz – 20 kHz |
| RMS power | 400 W |
| Rated impedance | 8 Ohm |
| Max SPL (1 m) | 133 dB (Fullrange) |
| Directivity (HxV) | 90° x 40° |
| HF | 1.4” exit, 2.4” v.c. |
| LF | 2x 10”, 2.4” v.c. |
| Crossover Frequency | 840 Hz |
| Signal Input | Terminal barrier strip (or speakON® using the SP-IS accessory |
panel)
Signal Output| Terminal barrier strip (or speakON® using the SP-IS accessory
panel)
Housing| Wooden box – black finished
Rigging Points| 4
Dimensions (WxHxD)| 300x780x430 mm (11.8×30.7×16.9 in)
Weight| 28.7 Kg (63.3 lbs.)
The warnings in this manual must be observed together with the “User Manual – Section 2”.
CONNECTIONS
PROTECTION AGAINST SOLID OBJECTS AND LIQUIDS (IP RATING)
The speakers are protected against the ingress of solid objects and liquids
with a rating of IP55 as defined by
IEC 60529. Please only use cables with the specified diameters:
PG7 => 6 or 6.5mm diameter
PG9 => 7.5 or 8mm diameter
Fasten properly the cable gland using the plastic tightening nut
WARNING!
Failure to comply with these installation prescriptions could adversely affect
the declared protection ratings.
CONFIGURATIONS
WARNINGS
WARNING: Make sure that the loudspeaker is securely installed in a stable position to avoid any injuries or damages to persons or properties. For safety reasons do not place one loudspeaker on top of another without proper fastening systems. Before hanging the loudspeaker check all the components for damages, deformations, missing or damaged parts that may compromise safety during installation. If you use the loudspeakers outdoor avoid spots exposed to bad weather conditions. The external wiring connected to speaker output terminals requires installation by qualified personnel only. Once the equipment is installed, prevent access to the connectors to unqualified personnel. Only use the accessories and configurations described in this manual, and proceed in accordance with the instructions given in the manuals for the accessories. dBTechnologies will not accept any responsibility for damages caused by inappropriate accessories or additional devices.
Installation and use of this equipment and its accessories must be performed only by “Expert personnel” according to safety standard. To prevent hazards to people, animals and/or objects, make sure that the installation is stable and secure. Comply with the safety regulations and laws in force in the country in which you use the product. For safe use, periodically check that all parts are in good working condition before use. Only authorised personnel may carry out design, calculations, installation, testing and maintenance of professional flown or stacked audio systems.
Check periodically the integrity and the functionality of the accessories and the technical equipments for a safe installation. user should never apply a load that exceeds the working load limits of any rigging components or equipment here presented. design, calculation, installation, testing and maintanance of suspension and stack systems for audio equipment must be performed only by qualified and authorized personnel. AEB Industriale s.r.l. denies any and all responsibility for improper installations, in the absence of safety requirements. Features, specification and appearance of products are subject to change without notice. dBTechnologies reserves the right to make changes or improvements in design or manufacturing without assuming any obligation to change or improve products previously manufactured.
Scan with your QR Reader App to download the complete User Manual.
A.E.B. Industriale Srl
Via Brodolini, 8
Località Crespellano
40053 VALSAMOGGIA
BOLOGNA (ITALIA)
Tel. +39 051 969870
Fax +39 051 969725
www.dbtechnologies.com
info@dbtechnologies-aeb.com
