B S Technology LA C 200FZ Varifocal Bullet Camera Instruction Manual
- June 11, 2024
- B S Technology
Table of Contents
B S Technology LA C 200FZ Varifocal Bullet Camera
Product Information
The LA C 200FZ is a high-quality color camera equipped with a 1/2.8 SONY Starvis Back-illuminated CMOS sensor. It has a resolution of 2M/5M Lite and supports both PAL and NTSC signal systems. With a minimum illumination of 0.001Lux/F1.2 and a S/N ratio of more than 52dB, this camera can capture clear images even in low light conditions. The camera also features an internal synchronous system, IR distance of up to 40 meters, and video output options including CVBS, CVI, TVI, and AHD. The camera is powered by DC12V (+/-10%) and has built-in auto gain control (AGC) and auto electronic shutter (AES) functions.
Product Usage Instructions
- Before using the camera, read the manual carefully and keep it safely for later use.
- Installation should be done by professional service and follow the manufacturer’s instructions. Do not dismantle without authorization.
- To prevent sensor damage, do not expose the lens to intense light sources for a long time.
- Do not touch the sensor directly. Cover the dustproof cover when the camera is not being used.
- Clean the camera with a dry soft cloth. If dirt is difficult to clean, use detergent with water and wipe dry the camera.
- Do not install the camera under an air conditioning’s air gate, or else the lens will blur with condensation of moisture.
- Ensure that all electric power sources are turned off when not in use, during installation, cleaning, etc.
- Transport, use, and store the camera in allowable temperature and humidity.
- If the camera is broken, contact the manufacturer or maintenance center. Do not modify or maintain without permission.
Common Problems and Troubleshooting
- No Picture after providing power: Check the power supply voltage and pole for accuracy. Check all connecting cables and monitors if they are correctly connected.
- The picture level direction have flowing interference ripples: This may be caused by power supply AC ripples. It needs to filter the wave of the power supply. Check the monitor and peripheral equipment used.
- The picture background color changes continuously: The fluorescent lamp’s electromagnetic field causes color roll. This is a proper phenomenon of the cameras. Reduce the fluorescent lamp numbers or increase the distance between the camera and the fluorescent lamps to improve it. Use a power supply external sync camera to solve it.
- The picture smear too much: The power supply’s voltage is unstable. Connecting cables are not connected correctly or have high impedance.
Thank you for using our product.
Before providing power for the camera, please read this manual carefully
before use.
We adopt the latest technical of sensor and driver. It owns the characters of
high definition and stability, strong anti-jamming, rich and real color.
Fixing and using this model are convenient too. It is very good for you to
apply to your CCTV system.
Main Features
- Auto Gain Control (AGC)
- Built-in auto gain control (AGC) circuit. The color camera Can get high definition picture in low Lux condition.
- Auto Electronic Shutter (AES)
- Built-in auto electronic shutter function. The color camera’s AES speed can reach 1/100,000s.
- Gama Characteristic
- Camera Gama characteristic is 0.45.
- Scanning Mode
- NTSC or PAL mode.
Note:
- Power supply must pass safety certification ,Its output voltage, current, voltage polarity and operating temper- ature must match requirement of this equipment.
- Please install lightning protection devices or cut off the power in thunder and lightning conditions.
- To capture high-quality video and pictures, please make sure the network connection is stable and smooth.
Device connection
Safety instruction
- Before using the camera, please read this manual carefully and keep it safe for later use.
- Installation should proceed by professional service and follow the manufacturer’s instructions, do not dismantle without authorization.
- In order to prevent the sensor, do not expose the lens to the intense light source for a long time.
- Do not touch the sensor directly. Please covers the dustproof cover when the camera is not being used.
- Please use a dry soft cloth to clean the camera. If dirt difficult to clean, use detergent with water and wipe dry the camera.
- Do not install the camera under air conditioning’s air gate ,or else the lens blur with condensation of moisture.
- Please ensure that all electric power sources are turned off when not open , installation ,clean, etc operation.
- Please transporting , using and storing the camera in allowable temperature and humidity.
- If the camera was broken, for example power cord or plug dam-aged,Splash liquid or foreign matter fall into camera, raining, wetting, etc can’t work situation, please contact manufacturer or maintenance center (modify and maintenance without perm ission, you must be responsible for the problems).
Common Problems and Troubleshooting
- No Picture after providing power
- May be the power supply voltage abnormity, please check he power supply voltage and pole whether exactitude. Please check all the connecting cable and monitors whether be connected correctly or not.
- The picture level direction have flowing interference ripples
- May be caused by the power supply AC ripples, it need filter the wave of the power supply.
- Check the monitor and peripheral equipments used.
- The picture background color changes continuously The fluorescent lamp’s electromagnetic field cause color roll. This is proper phenomenon of the cameras.
- Reduce the fluorescent lamp numbers or increase the distance between the camera and the fluorescent lamps can improve it.
- Use power supply external sync. camera can solve it.
- The picture smear too mass
- The power supply’s voltage unstable.
- Connecting cables not connect correctly or have high impedance.
Note:
- Please note the camera’s operating temperature and its using environment requirement. Avoid using the camera at too high or too low temperatures. The operating tem perature is -30~+60℃. (Recommendatory operating tem perature is -10~+50℃.)
- Do not mount the camera near by the radiator or heater.
Specification
Model
|
LA C 200FZ
---|---
Image Sensor
|
1/2.8″ SONY Starvis Back-illuminated CMOS sensor
Resolution
|
2M/5M Lite
Signal System
|
PAL / NTSC
Minimum Illumination
|
0.001Lux/F1.2
S/N Ratio
|
More than 52dB
Synchronous System
|
Internal
IR Distance
|
40 Meters
IR Power On
|
Video Auto Control
Video Output
| CVBS / CVI / TVI / AHD
Power
|
DC12V(+/-10%) <12W
Lens
|
2.8-12mm Manual Zoom Lens
Weather Proof
|
IP66
Dimension (mm)
|
220(W) x 80(H) x 80(D)
Weight (g)
|
1400
Operating Conditions
|
-10~+50℃ RH95% MAX
Accessories list
| Name | Number |
|---|---|
| Camera | 1 |
| User Guide | 1 |
Notes:
Do not attempt to disassemble the camera. If the camera can not work, please
contact the local franchiser or our company.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>