CRESTRON ZUMMESH-JBOX-FMKT-CP Chicago Plenum Enclosure Wireless J-Box Devices User Manual

ZUMMESH-JBOX-FMKT-CP Chicago Plenum Enclosure Wireless J-Box Devices

ZUMMESH- JBOX-FMKT-CP
Chicago Plenum Enclosure for Zūm™ Wireless J-Box Devices
The Crestron® ZUMMESH-JBOX-FMKT-CP is an air-tight, Chicago Plenum compliant enclosure that is designed to secure a Zūm™ wireless J-Box device. The enclosure has an integrated divider that separates Class 1 and Class 2 wiring and provides a 1/2 in. knockout to secure the Zūm J-Box device.

Check the Box

Screw, 08-32 x 1/2 in., Undercut Head, Flat, Phillips, Zinc Plated, Steel, White (P/N 2053996)| 4

Install the ZUMMESH-JBOX-FMKT-CP

To install the ZUMMESH-JBOX-FMKT-CP, the enclosure must be mounted in the plenum space, the Zūm J-Box device must be secured in the enclosure and properly wired, and the plastic cover must be installed.
Secure the Enclosure in the Chicago Plenum
Secure the enclosure to a stud, hanger, or conduit. Dimples are placed on the bottom of the enclosure to prevent drill bits from walking when drilling holes in the enclosure.
The opening of the enclosure must be located in the room, outside of the plenum space.
NOTE: The enclosure must be mounted so that the open edge of the box is flush to the drop ceiling panel on the room side or protruding slightly into the room.
Install the Zūm J-Box Device in the Enclosure.
A metal divider with a 1/2 in. knockout is used to secure the Zūm J-Box device in the enclosure.
NOTE: The metal divider is welded in place and must not be removed under any circumstance.

1. Insert the wires and threaded plastic of the Zūm J-Box device through the 1/2 in. knockout in the metal divider.
2. Secure the Zūm J-Box device to the metal divider with a conduit nut (supplied with the Zūm J-Box device). For optimal wireless communication, orient the Zūm J-Box device as indicated below.

• When a ZUMMESH-NETBRIDGE is used, the J-Box device must be oriented with the ZUMMESH-NETBRIDGE towards the opening of the enclosure.
• When ZUMMESH-NETBRIDGE is not used, the J-Box device must be oriented with the SET and TEST buttons away from the opening in the enclosure.

Install a Zūm J-Box device with a ZUMMESH-NETBRIDGEInstall a Zūm J-Box device without a ZUMMESH-NETBRIDGE Wire the Zūm J-Box Device
NOTES:

• Only knock out the opening intended for use in the installation.
• Partially knocking out any opening will cause the box to no longer be Chicago Plenum rated.

1. Connect Chicago plenum rated flexible metal conduit to the Class 1 side of the enclosure. To facilitate wiring, five push-back style, air-tight knockouts are provided on the Class 1 side of the enclosure; two 3/4 in. knockouts and three 1/2 in. knockouts.

2. Wire the Zūm J-Box device as described in its manual. Refer to the Zūm J-Box device  manual at www.crestron.com/manuals for wiring instructions. The illustration that follows is for reference only.
   NOTE: If necessary, make Class 2 connections between the Zūm J-Box device and other low-voltage devices. To facilitate wiring, ten push-back style, air- tight knockouts are provided on the Class 2 side of the enclosure; six 3/4 in. knockouts and four 1/2 in. knockouts.

3. Connect the ground wire to the ground tab on the divider in the enclosure.
   NOTE: The electrical box as well as the equipment installed in the box must be grounded using the included #8 grounding lock washer, #8-32, 3/8 in. grounding screw, and 18 AWG (minimum) wire that has been terminated with an appropriate ring terminal.

Wire the Zūm J-Box Device – Example Secure the Plastic Cover
Secure the plastic cover to the enclosure using the provided screws.
The cover protrudes 0.125 in. (3 mm) from the surface of the ceiling.

Additional Information

Scan or click the QR code for detailed product information.http://www.crestron.com/direct/ZUMMESH-JBOX-FMKT-CP
ZUMMESH-JBOX-FMKT-CP

Compliance and Legal
Original Instructions: The U.S. English version of this document is the original instructions. All other languages are a translation of the original instructions.
Regulatory Model: ZUMMESH-JBOX-FMKT-CP
This product is Listed to applicable UL® Standards and requirements tested by Underwriters Laboratories Inc.
The product warranty can be found at www.crestron.com/warranty.
The specific patents that cover Crestron products are listed at www.crestron.com/legal/patents.
Certain Crestron products contain open source software. For specific information, please visit www.crestron.com/opensource.
Crestron, the Crestron logo, and Zūm are either trademarks or registered trademarks of Crestron Electronics, Inc. in the United States and/or other countries. UL and the UL logo are either trademarks or registered trademarks of Underwriters Laboratories, Inc. in the United States and/or other countries. Other trademarks, registered trademarks, and trade names may be used in this document to refer to either the entities claiming the marks and names or their products. Crestron disclaims any proprietary interest in the marks and names of others. Crestron is not responsible for errors in typography or photography.
©2019 Crestron Electronics, Inc.

Crestron Electronics, Inc.
15 Volvo Drive, Rockleigh, NJ 07647
Tel: 888.CRESTRON
Fax: 201.767.7576
www.crestron.com
Quick Start – Doc. 8461B
(2053755)
Specifications subject to change without notice.

References

• Control Systems for Home Automation, Campus & Building Control by Crestron Electronics [Crestron Electronics, Inc.]
• Crestron Lighting | World Class Lighting Solutions
• Patents [Crestron Electronics, Inc.]
• Search Results [Crestron Electronics, Inc.]
• Open Source Software [Crestron Electronics, Inc.]
• Standard Terms & Conditions and Warranties [Crestron Electronics, Inc.]
• Manual-Hub.com – Free PDF manuals!

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>