db DRIVE WDX8 3K 8 Inch Subwoofer User Manual
- June 17, 2024
- DB DRIVE
Table of Contents
db DRIVE WDX8 3K 8 Inch Subwoofer
WDX6.5 3K WDX8 3K WDX10 3K
Installation Instructions
Due to continuous improvement of the product, specifications are subject to change without notice.
Introduction
Congratulations on your purchase of a DB Drive state-of-the-art subwoofer. Your selection of a DB Drive car audio product indicates a true appreciation of fine musical reproduction. Whether adding to an existing system or including your DB Drive subwoofer in a new system, you are certain to notice immediate performance benefits.
Keep Your Sales Receipt
Take this time to attach your sales receipt to the manual and put in a safe
place. In case of any unforeseen reason this product may need warranty
service, your receipt will be necessary to establish the purchase date.
Recommendation
A power subwoofer’s performance is only as good as its installation. Proper
installation will maximize the system’s overall performance. It is recommended
that you have our product installed by an authorized DB Drive retailer.
However, if you decide to install it yourself, please carefully read through
this manual and take your time to do a quality installation.
IMPORTANT! Before making any connections, disconnect the car’s battery until the installation is completed to avoid possible damage to the electrical system.
WARNING!
Exposure to a high-power sound system can cause hearing loss or damage.
Listening to your system at loud levels while driving will impair your ability
to hear traffic sounds and emergency vehicles. Use common sense when listening
to your system.
PRODUCT SPECIFICATIONS
CALCULATING ENCLOSURES
It is recommended to build your enclosure from at least 3/ 4” thick MDF (medium-density fiberboard). Make sure the enclosure is sealed airtight.
Calculating External Volume
- To calculate box volume, measure the outside Width x Height x Depth of the enclosure. Example 12” x 14” x 9”=1512 ÷ 1728” Cubic feet
- Next, you must convert cubic inches into cubic feet. To do this, you must divide the cubic inches total by 1728”. Example 1512 ÷ 1728=.875 Cubic feet
Calculating Internal Volume
- To calculate the internal (net) volume of the above box you must first multiply the thickness of the wood you are using by Two(2). Example 3/4” x 2= 1.5“
- Next, subtract 1.5 from each of the outside measurements of the box.
- Multiple the new totals (H x W x D) Example: 10.5 x 12.5 x 7.5 = .5696
- Next, you must convert cubic inches into cubic feet. To do this, you must divide the cubic inch total by 1728”. Example 984.375 ÷ 1728=.5696 cubic feet.
RECOMMENDED ENCLOSURES
WDX6.5 3K
- Sealed Enclosure
- Box Volume: 0.33 cu ft. / 9.34 L
Ported Enclosure
- Box Volume: 0.64 cu ft. / 18.12 L Box Turning: 38Hz
- Port Area: 3.14 sq in. / 20.27 cm2 Port Length: 9 in / 22.86 cm
WDX8 3K
- Sealed Enclosure
- Box Volume: 0.6 cu ft. / 16.99 L
Ported Enclosure
- Box Volume: 0.9 cu ft. / 25.49 L Box Turning: 38Hz
- Port Area:7.7 sq in. / 45.6 cm2 Port Length: 14.7 in / 37.44 cm
WDX10 3K
- Sealed Enclosure
- Box Volume: 1 cu ft. / 28.32 L
Ported Enclosure
- Box Volume: 1.2 cu ft. / 33.98 L Box Turning: 36Hz
- Port Area: 7.7 sq in. / 45.6 cm2 Port Length: 11 in / 27.94 cm
DB Research L.L.P.
302 Hanmore Industrial Parkway Harlingen, TX 78550
TM Phone 877-787-0101: Fax
956-421-4513:
www.DBDrive.net
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>