LIAN LI O11D EVO RGB Right Side Panel and Top Cover User Manual

O11D EVO RGB Right Side Panel and Top Cover
User Manual

O11D EVO RGB Right Side Panel and Top Cover

Remove the Right Side Panel and Top Cover Remove the front & side glass panel 

1. Remove the protecting clip
2. Peel off the protective film on both sides
3. Recommend to keep the protecting clip on for transportation

Remove the Front Pillar
Make sure to fix the pillar for transporting

Normal Mode Specifications

Refer to page 1-15, 28-29 to install this modeA. Power Button, Reset Button, C button for color control, M button for lighting mode control, B button for light brightness control
B. IO ports: 1 x AUDIO / Microphone Combo Jack, 2 x USB 3.0, 1 x USB 3.1 Type C,
C. Supporting 120 mm fan x 3 or 140 mm fan x 3 or 360 mm radiator x 1 or 420 radiator x 1
D. Supporting 120 mm fan x 3 or 140 mm fan x 3 or 360 mm radiator x 1 or 280 radiator x 1 or 2.5” SSD x 4 or 3.5” HDD x 2
E. Supporting 120 mm fan x 3 or 140 mm fan x 3 or 360 mm radiator x 1
F. Supporting 120 mm fan x 1
G. Removable HDD tray, Supporting 2.5” SSD x 2 or 3.5” HDD x 2
H. Removable HDD tray, Supporting 2.5” SSD x 2
I. Removable PSU mounting bracket
Reverse Mode Specifications
Refer to page1-4, 16-29 to install this modeA. Power Button, Reset Button, C button for color control, M button for lighting mode control, B button for light brightness control
B. IO ports: 1 x AUDIO / Microphone Combo Jack, 2 x USB 3.0, 1 x USB 3.1 Type C
C. Supporting 120 mm fan x 3 or 140 mm fan x 3 or 360 mm radiator x 1, or 280 mm radiator x 1
D. Supporting 120 mm fan x 3 or 140 mm fan x 3 or 360 mm radiator x 1 or 280 radiator x 1 or 2.5” SSD x 4 or 3.5” HDD x 2
E. Supporting 120 mm fan x 3 or 140 mm fan x 3 or 360 mm radiator x 1
F. Supporting 120 mm fan x 1
G. Supporting 2.5” SSD x 1 + 3.5” HDD x 2 or 2.5” SSD x 2
H. Removable HDD tray, Supporting 2.5” SSD x 2
I. Removable PSU mounting bracket

Hardware List

For graphic card anti-sag bracket kit installation
I/O Ports Function

M-Mode/| Press one time| 14 Lighting Effects Mode
Single-Color Modes: Breathing/Pulse/Interstellar Multi-Color Modes: Dual-Color Interstellar/Color Clash/ Color Paint/Meteor Stack/Ripple/Runway
*Press“C”to change the color for above lighting effects mode Set Modes: Breathing Cycle/Rainbow/Rainbow Morph/
Color Spill / Fireworks
Above lighting effects can’t change color
---|---|---
Long press 3 sec| Sync or deactivate motherboard mode/
C-Color /| Press one time| Single-color effects switch and pure color mode has 11 colors. Multi-color effects switch has 5 sets/
Long press 3 sec| Enter or deactivate pure color mode with a total of 11 colors (Fixed colors: Red, Green, Blue, White, Orange, Yellow, Teal, Sky Blue, Light Blue, Purple, Magenta)/
BBrightness/| Press one time| Adjust the brightness of the lighting in five levels (100%, 75%, 50%, 25%, 0%)/

Details for the lighting strips:

1. Both the top and bottom each have 47 ARGB LEDs.
2.  Included memory function.
3.  The default lighting effect mode is Fireworks

Definition

1| Power LED+
2| Power LED-
3| Power SW+
4| Power SW-
5| Reset SW+
6| Reset SW-

2.5″ SSD Installation PSU Installation Way 1: Install Directly, Way 2: Remove the bracket and install,
IO Module Location Motherboard Installation Support of Lower Position (Default Position) Switch Motherboard Mounting Position Support of Upper Position 2.5″ SSD, 3.5″ HDD Installation
Remove the dust filters

Cable management Cable holder installation

Use of cable holder

Keep the big cables in the cable holders Hold the small cables with the velcro straps Remove the velcro strap to place a controller= Remove the Bottom Fan Bracket Remove the Top Fan Bracket

Instructions for Using the 420 Water Cooling Mounting Bracket/420 Remove Hard Drive Bracket 2.5″ SSD, 3.5″ HDD installation Remove the Side Fan Bracket Attention: The fan bracket can be reversed, there are 4 installation style Graphic Card Anti-sag Bracket Installation
Installation 1(FOR ATX MB )Installation 2 (FOR ATX MB ) Right Side Panel Installation Side & Front Glass Installation  Top cover Installation Reverse Mode Installation

1. Remove the bottom fan bracket
2. Remove the top fan bracket
3. Remove the top panel
4. etach the feet frame from the chassis (Remove the I/O module before)
5. Remove the PSU support bracket/
6. Swap the PSU mounting bracket and hard drive bracket positions
7. Install the power supply support bracket
8. Install to the feet frame

2.5″ SSD Installation

PSU Installation

Way 1: Install Directly,![LIAN LI O11D EVO RGB Right Side Panel and Top Cover

• PSU Installation1](https://manuals.plus/wp-content/uploads/2024/02/LIAN-LI- O11D-EVO-RGB-Right-Side-Panel-and-Top-Cover-PSU-Installation1.jpg)Way 2: Remove the bracket and install,
  2.5″ SSD, 3.5″ HDD Installation
  If space is needed, the hard drive cage can be removed I/O Module Location

Motherboard Installation Support of Upper Position (Default Position) The stand-off bolts mount at the upward arrow position
Switch Motherboard Mounting Position Support of Lower Position The stand-off bolts mount at the downward arrow position
Cable management
Cable holder installation Use of cable holder Install the Top Fan Bracket Bottom fn brcket Instlltion Dust Filter Installation Remove Hard Drive Bracket 2.5″ SSD, 3.5″ HDD installation
Remove the Side Fan Bracket Attention: The fan bracket can be reversed, there are 4 installation style Graphic Card Anti-sag Bracket Installation
Installation 1(FOR ATX MB)Installation 2 For E-ATX MB Right Side Panel Installation Side & Front Glass Installation  Top cover Installation Hardware Clearance

Option Kits

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>