electroair EA-13000 Starter Switch Panel Installation Guide

EA-13000
Installation Manual
Ignition/Starter Switch Panel

Electroair Acquisition Corp.
5097 Williams Lake Road
Waterford, MI 48329 U.S.A.
Phone: 248-674-3433 Fax: 248-674-4231
Email: sales@electroair.net

Revision Log

Revision| Pages Affected| Date of Revision| Description of Revision| Approved by| Date of FAA Approval
---|---|---|---|---|---
0| | 5/12/2015| Initial Release| | 8/26/2015
1| | 5/12/2016| ECO 1019-0007| | 5/12/2016
2| | 6/20/2016| ECO 1019-0016| | 2/3/2017
3| 1,2,4 ,5 ,7′
8,9| 2/4/2020| ECO 1019-0079| |
4| 4, 7-8| 8/27/2021| ECO 1019-0099| |

Overview of Ignition/Starter Switch Panel Installation

Thank you for purchasing an Electroair Ignition/Starter Switch Panel for Electroair electronic ignition system-equipped aircraft. Electroair is confident that you will be happy with the performance of the Electroair Ignition/Starter Switch Panel for Electroair electronic ignition system- equipped aircraft. The next pages will provide a step-by-step process of installing the EIS on the aircraft. Electroair hopes you will enjoy the experience and that this manual will provide clear direction and guidance through this process. This manual will cover the following general installation steps:

1. General overview and recommendations
2. Removal of old ignition components
3. Set-up & installation of p/n: EA-13000 Ignition/Starter Switch Panel
4. Final installation steps

Electroair strongly recommends reading through this entire installation procedure before installing the Electroair Ignition/Starter Switch Panel for your Electroair electronic ignition system-equipped aircraft. Make sure that any questions are answered before the actual installation. Also, make sure any extra components needed, e.g. cable ties, switch terminations, etc., are available. Removal of old components and installation of new components shall be completed in compliance with CFR Title 14 Part 43, as applicable, and any Airframe or Engine Manufacturer Maintenance Procedures, as applicable. Above all else, use good common sense and professional judgment. An ignition/starter switch panel is an electrical device. If an ignition/starter switch panel is improperly installed, severe damage could be caused to the ignition/starter switch panel, EIS, aircraft, or installer including bodily injury or death.
Please contact Electroair with any questions during this installation process. Good luck and happy flying!!
Electroair

EA-13000 Kit Description & Requirements

EA-13000 System Description & Requirements:

1. This kit replaces the rotary key switch on aircraft with an EIS kit installed.

Other items needed:

1. Basic tools and standard aircraft hardware are required for mounting EA-13000 Ignition/Starter Switch Panel.
2. Electrical tools for cutting, stripping, and terminating various wiring. Also recommended is a good selection of cable ties for harness routing and tie-off, and a selection of shrink tubing for covering exposed electrical connections.

EA-13000 Kit Contents
EA-13000 Kit Contents:

1.  ___EA-13000 Panel with Switches
2.  ___Baggie with connectors and connecting hardware
3.  ___USB Drive Containing System Documents (Installation Manual, STC, ICA)
4.  ___Warranty registration–
   USE THIS TO OBTAIN THE STC AUTHORIZATION LETTER

Receiving and Acceptance Checking of EIS Kit

1. Inspect the packaging for damage before acceptance from the freight carrier. If damaged, refuse the package.
2. Open the package.
3. Inventory the contents of the package to the content listing of the package.
4. Are all of the materials there? If yes, proceed to step 5. If no, proceed to step 9.
5. Inspect the switches for broken plastic.
6. Inspect the panel for bends
7. Are all materials acceptable?
8. If yes, proceed with the installation.
9. If not, contact the factory. Have the serial number of the kit available when contacting. (factory 248-674-3433 or sales@electroair.net)

If possible, store parts in original packaging when not in use. If not possible, wrap parts in cushioning material and place them in one location. Review above prior to reinstallation.

For the latest copies of documentation, refer to www.electroair.net.

• Approved Model Listing (AML)

• Approved Flight Manual
  Supplement (AFMS)

• Instructions for Continued
  Airworthiness (ICA)

• Installation Manual (IM)

• Supplemental Type Certificate (STC)

• Trouble Shooting Instructions (TSI)

Precautionary Statements:

• ALWAYS STAY OUT OF THE PROPELLER ARC!

• CAUTION: Disconnect the battery before starting this procedure.

• CAUTION: Prior to any drilling or cutting, verify that there is proper clearance.

• CAUTION: Do not cut or alter any structural tubing, aluminum panels, or skin.

• CAUTION: Follow these instructions very carefully to ensure a correct hook-up of the Ignition/Starter Switch Panel. Skipping ahead or taking shortcuts increases the risk of an incorrect installation and either a poor performing EIS or the possibility of damaging equipment. Prior to turning on bus power, verify the wiring. Please call Electroair with any questions (sales@electroair.net or 248674-3433).

• CAUTION: Do not secure any radio communication, navigation, transponders, or intercom wiring to any ignition-related wires, boxes, or sensors. Doing so will cause poor to noisy transmission or reception of com and intercom and/or poor or no navigation function. Keep at least 3 inches between these wires.

• CAUTION: If using a non-impulse coupled magneto aka direct-drive magneto aka non-starting magneto, update pilot checklist/ POH to have MAG switch in OFF position during starting.

• Consult with an appropriately licensed mechanic.

• Consult applicable service manuals for the aircraft.

Installation of EA-13000:

General Overview and Recommendations:

• Determine the proper location for the panel.
• Determine the most appropriate mounting method.
• Overall dimensions are provided in Figure 1 and Figure 2. Cutout dimensions are provided in Figure 3 and Figure 4. All dimensions are in inches.

Removal of Old Ignition Components:

• Remove the existing rotary key switch.
• Label all leads affixed to the rotary key switch in the process.
• Save all of the parts for future reference.
• If EIS was previously installed, either coil and stow P-lead wire or carefully clip Plead wire from the harness.
• If EIS is not previously installed, remove P-lead from the magneto that is being converted to the EIS system.
• If the ignition/starter switch panel is not being installed in the rotary key switch location, plug the hole left by removing the rotary key switch as necessary.

Set-up & Installation of p/n: EA-13000 Ignition/Starter Switch Panel:

• Review the leads corresponding to the location of the ignition/starter switch panel.
  o Are they of the appropriate length?
  o If not, adjust in accordance with 43.13-1B Change 1 section 11-167.

•  Remove the material of the instrument panel in accordance with the cutout provided. Be advised that the drawing scale is not 1:1. All dimensions are in inches.

• CAUTION: Before cutting or drilling verify space is clear behind the instrument panel.

• CAUTION: Use extreme care so as to not damage any wiring, instruments, structural, or fuel lines.

• CAUTION: The connectors and connecting hardware for the starter switch are small. Take extreme care not to lose them.

• CAUTION: Ensure electrical connectors are tight on switch connections. Ensure wires will not pull out of any electrical connections.

•  EIS Switch
  o Use this switch as the EIS Ignition Switch shown in the EIS schematic.
  o Connect C1 Pin 6 to connector labeled EIS.
  o Connect connector labeled B+ to the 2A breaker or fuse.

• Mag Switch
  o Use this switch as the Magneto Switch.
  o Connect ground to GND.
  o Connect the P-Lead to P-LEAD.

• Starter Switch
  o Use this switch as the Start Switch.
  o Connect the lead from the starter terminal of the ignition switch to terminal 1.
  o Connect B+ to terminal 2.

•  Insulate any exposed electrical connections in accordance with 43.13-1B Change 1 section 11-159.

• Insert ignition/starter switch panel into the instrument panel and screw down using standard hardware.

Final Installation Steps:

• CAUTION: If using a non-impulse coupled magneto aka direct-drive magneto aka non-starting magneto, update pilot checklist/ POH to have MAG switch in OFF  position during starting.

• Start the aircraft per the AFMS and perform a ground run-up.
  o Check for proper starter function.
  o Check for proper RPM drop on EIS.
  o Check for proper RPM drop on magneto.

• If the aircraft passes, then return to service.

• If the aircraft fails, then verify that all of the connections are correct and competent and that no other wires were damaged during the installation. Repeat the start-up process.

• If the aircraft fails a second time, contact the factory for support. (248-674-3433 or sales@electroair.net)

Glossary and Abbreviations:

AD(s) – Airworthiness Directive(s)
AFM – Aircraft Flight Manual
AFMS – Aircraft Flight Manual Supplement
ALS – Aircraft Limitations Section
AML – Approved Model List
APU – Auxiliary Power Unit
BTDC – Before Top Dead Center
CFR – Code of Federal Regulations
CSTW – Crank Shaft Trigger Wheel
EIS – Electronic Ignition System
FAA – Federal Aviation Administration
Ignition Timing – is the process of setting the angle relative to piston position and crankshaft angular velocity that a spark will occur in the combustion chamber near the end of the compression stroke.
IAW – In Accordance With
ISSP – Ignition/Starter Switch Panel
MAG – magneto
MAP – Manifold Absolute Pressure
May/Should – an optional requirement
MTH – Mag Timing Housing
Must/Shall – a mandatory requirement
RPM – Revolutions per Minute
POH – Pilot’s Operating Handbook
STC – Supplemental Type Certificate
TDC – Top Dead Center

Electroair Acquisition Corp.
Revision 04| IM EA-13000
Prepared by: EAC| Page 10 of 10
08/27/2021
---|---|---

References

• Electroair Electronic Ignition Systems

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>