DENON AVR-1612 AV Surround Receiver Owner’s Manual

DENON AVR-1612 AV Surround Receiver

Specifications

• Model: AVR-1612
• Channels: 5.1
• Home Theater System: Yes
• Supported Languages: Svenska, Nederlands, Italiano, Deutsch, English

Safety Precautions

CAUTION: RISK OF ELECTRIC SHOCK DO NOT OPEN
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER- SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
The lightning flash with the arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated dangerous voltage within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.

IMPORTANT SAFETY INSTRUCTIONS:

1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with a dry cloth.
7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
9. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.
10. Only use attachments/accessories specified by the manufacturer.
11. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.
12. Unplug this apparatus during lightning storms or when unused for long periods of time.
13. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
14. Batteries shall not be exposed to excessive heat such as sunshine, fire or the like.

CAUTION: To completely disconnect this product from the mains, disconnect the plug from the wall socket outlet. The mains plug is used to completely interrupt the power supply to the unit and must be within easy access by the user.

Product Usage Instructions

Installation

1. Refer to the manufacturer’s instructions for installation guidance.
2. Ensure that the receiver is placed on a stable surface, away from heat sources such as radiators, heat registers, or stoves.
3. Make sure the ventilation openings are not blocked to prevent overheating.
4. Connect the appropriate audio and video cables to the input and output ports of the receiver.
5. Connect the speakers to the corresponding speaker terminals on the receiver.
6. Plug in the power cord to a wall socket outlet.

Connection

1. Refer to the manufacturer’s instructions for connection guidance.
2. Connect your audio and video sources, such as Blu-ray players, gaming consoles, or set-top boxes, to the input ports of the receiver.
3. Connect your TV or display device to the output port of the receiver.
4. Ensure that all connections are secure and properly inserted.

Setup

1. Turn on the receiver and your audio and video sources.
2. Access the setup menu on the receiver using the provided remote control or front panel controls.
3. Follow the on-screen instructions to configure your audio and video settings, such as speaker configuration, audio modes, and video output resolution.
4. Save your settings and exit the setup menu.

FAQ

Q: Can I use this receiver with a 7.1-channel home theater system?
A: No, this receiver is specifically designed for use with a 5.1-channel home theater system.

Q: How do I update the firmware of the receiver?
A: To update the firmware, visit the manufacturer’s website and download the latest firmware file. Follow the instructions provided in the firmware update guide to install the update on the receiver.

Q: Can I connect wireless speakers to this receiver?
A: No, this receiver does not support wireless speaker connections. You will need to use wired speakers for audio playback.

Q: What is the warranty period for this product?
A: The warranty period for the AVR-1612 is one year from the date of purchase. Please refer to the warranty card or contact the manufacturer for more information.

Getting Started
Explains how to easily install, connect, and set up a 5.1-channel home theater system.
Explains all operations of your receiver. Open the included CD-ROM on your computer for detailed operating instructions.

D&M Holdings is striving to be a paperless company in order to help preserve the environment. Your cooperation and understanding is appreciated.

Read before use
Thank you for purchasing this DENON product.
This manual explains the Setup Wizard that you will need to perform directly after removing the product from its packaging before you start using the product. The Setup Wizard displays easy-to-follow guidance on your television screen that shows you how to connect and configure speakers, various other devices, and network functions for full enjoyment of this unit

Accessories

Check that the following parts are supplied with the product.

• Getting Started………………………………………………………………. 1
• CD-ROM (Owner’s manual)…………………………………………….. 1
• Service network list………………………………………………………… 1
• Power cord……………………………………………………………………. 1
• Remote control unit (RC-1157)…………………………………………. 1
• R6/AA batteries……………………………………………………………… 2
• Setup microphone (DM-A409)………………………………………….. 1
• AM loop antenna……………………………………………………………. 1
• FM indoor antenna…………………………………………………………. 1

About this manual

operation buttons
The operations described in this manual are based mainly on remote control operations.

Symbols

This symbol indicates a reference page on which related information is described.
This mark indicates the page of the owner’s manual on the CD-ROM provided.
This symbol indicates a supplementary information and tips for operations.

NOTE This symbol indicates points to remember operations or function limitations.

illustrations
Note that the illustrations in this manual is for explanation purposes and may differ from the actual unit.

About the CD-ROM
(Getting Started / Owner’s manual)

You need to have Adobe Reader installed on your computer to view the owner’s manuals on the CD-ROM. Click the Adobe Reader banner in the CD-ROM menu to install the Adobe Reader (for Windows).

Cautions on handling

• Before turning the power on
  Check once again that all connections are correct and that there are no problems with the connection cables. Power is supplied to some of the circuitry even when the unit is set to the standby mode. When going on vacation or leaving home for long periods of time, be sure to unplug the power cord from the power outlet.

• About condensation
  If there is a major difference in temperature between the inside of the unit and the surroundings, condensation (dew) may form on the operating parts inside the unit, causing the unit not to operate properly.If this happens, let the unit sit for an hour or two with the power turned off and wait until there is little difference in temperature before using the unit.

• Cautions on using mobile phones
  Using a mobile phone near this unit may result in noise. If that occurs, move the mobile phone away from this unit when it is in use.

• Moving the unit
  Turn off the power and unplug the power cord from the power outlet. Next, disconnect the connection cables to other system units before moving the unit.

• About care

  • Wipe the cabinet and control panel clean with a soft cloth.
  • Follow the instructions when using a chemical cleaner.
  • Benzene, paint thinner or other organic solvents as well as insecticide may cause material changes and discoloration if brought into contact with the unit, and should therefore not be used.

Preparing the Setup Wizard

This section describes how to prepare the Setup Wizard before use.

• Do not plug the power plug of the main unit into the wall socket until these preparations are complete.
• Speaker connections are performed using the Setup Wizard. Do not connect the speakers yet.

What you need for this step

1. Place and layout speakers
   Before installing the speakers, connect the speaker cables to the speakers. For details on how to connect the speaker cables, see the speaker instruction manual. Connect the speaker cables to the main unit using the Setup Wizard.
   Install the surround speakers in a position 60 to 90 cm higher than the ear level.
   

2. Connect this unit to the television using an HDMI cable (sold separately)
   NOTE If this unit is connected using cables other than the HDMI cable, the Setup Wizard will not be displayed.

3. Turn the television power on, and switch the video input to this unit (HDMI input)
   For details on how to operate the television, see the television instruction manual.

4. Insert the provided batteries into the remote control unit
   

5. Slide the rear lid in the direction of the arrow and remove it.

6. Load the two batteries properly as indicated by the marks in the battery compartment

7. Put the rear cover back on.

Setup Wizard

When preparations are complete, start the Setup Wizard. Use the Setup Wizard to perform connections and settings as shown in the following steps. Perform the operations as described in the instructions on the screen. You can skip or cancel at each section if necessary.

1. Language Select
   Set the language for the instructions on the television screen.
   These settings can be changed in the following menu even after setting the Setup Wizard ( page 67 “Language”).
   NOTE If your language is not available, select “English”.

2. Speaker Connection
   Connect the speakers for surround sound.
   NOTE Connections for speakers other than 5.1 channel speakers cannot be set using the Setup Wizard. Select “Others”, and then select “Skip” in “2. Speaker Connection” to proceed to “3. Speaker Calibration”. (For details on the setting method, see page 36 “Speaker installation/connection (Advanced connection)”.)

3. Speaker Calibration
   Configure the settings for your speakers and for the optimum surround sound for your room.
   These settings can be changed in the following menu even after setting the Setup Wizard ( page 11 “Set up speakers (Audyssey® Auto Setup)”).

4. Source Setup
   Set the connecting terminals for each device to be set, and connect to the terminals.
   These settings can be changed in the following menu even after setting the Setup Wizard ( page 70 “Input Assign”).

5. Remote Setup
   Configure the settings so that devices connected to this unit can be operated using the provided remote control.
   These settings can be changed in the following menu even after setting the Setup Wizard ( page 66 “Remote Setup Guide”).

Basic operation of Setup Wizard

Getting Started

1. Insert the main unit power plug into the wall socket.

2. Press AMP to set the remote control unit to AMP operation mode. This remote control is a preset remote control that can be used to control connected devices.
   When power is switched to standby
   Press STANDBY ( ).GPower indicator status in standby mode

   • Normal standby: Off
   • When “HDMI Control”( page 64) is set to “ON”: Red
     NOTE During power standby, a minimal amount of power is consumed. To totally cut off the power, remove the power cord from the power outlet.

3. Press ON ( ) to this unit.
   The power switches on, and the Setup Wizard start screen is displayed on the television screen.

4. Press ENTER.
   Start the Setup Wizard
   Setup Wizard has started. Please follow the message on the screen.
   To start the Setup Wizard again after exiting it, select “Setup Wizard” in the menu ( page 48 “Menu map”).

Connecting the speakers
The speakers are connected in “2. Speaker Connection” of the Setup Wizard but if you did not use or cancel the Setup Wizard, connect the speakers as shown below. For details, see the included CD-ROM (Owner’s manual).

Connect
Carefully check the left (L) and right (R) channels and + (red) and – (black) polarities on the speakers being connected to this unit, and be sure to interconnect the channels and polarities correctly.

Connecting the speaker cables
Peel off about 10 mm of sheathing from the tip of the speaker cable, then either twist the core wire tightly or terminate it.

NOTE

• Connect so that the speaker cable core wires do not protrude from the speaker terminal. The protection circuit may be activated if the core wires touch the rear panel or if the + and – sides touch each other (vm page 92 “Protection Circuit”).
• Never touch the speaker terminals while the power supply is connected. Doing so could result in an electric shock. (When the Setup Wizard is running, follow the instructions in the Setup Wizard screen for making connections.)
• Use speakers with the speaker impedances shown below.

5.1-channel

Playback (Basic operation)

Here, we explain how to perform simple operations. For details, see the included CD-ROM (Owner’s manual).

Important information
Before starting playback, make the connections between the different devices and the settings on the unit.

NOTE
Also, refer to the operating instructions of the connected devices when playing them.

You can also use the following operation to select an input source.

Using the button on the main unit
Press SOURCE  or SOURCE .
• Every time you press SOURCE d or SOURCE f, the input source switches in the following order

When iPod   on the main unit is pressed, the input source of this unit is switched to “DOCK” or “USB/iPod” and the connected iPod is automatically played ( page 24 “iPod play function”).

Using the “Source Select” menu

1. Press SOURCE SELECT.
   Display the “Source Select” menu.

2. Use to select the input source, then press ENTER.
   The input source is set and the source selection menu is turned off.

• When using an iPod connected directly to the USB port of this unit, select “USB/iPod” for the input source.
• Input sources that are not going to be used can be set ahead of time. Make this setting at “Source Delete” ( page 65).
• To turn off the source selection menu without selecting an input source, press SOURCE SELECT again.
• When SOURCE SELECT is pressed, the AMP operation mode starts automatically ( page 73).

You can also operate via the main unit. In this case, perform the following operations. Turn MASTER VOLUME to adjust the volume.

• The sound is reduced to the level set at “Mute Level” ( page 65).
• To cancel, press again. Muting can also be canceled by adjusting the master volume.

Other operations

• See the following items on the included CD-ROM(Owner’s manual).
• Playing a Blu-ray Disc player/DVD player
• Playing an iPod
• Tuning in radio stations
• Playing a USB memory device
• Selecting a listening mode (Surround mode)
• Convenient functions
• How to make detailed settings
• Operating the connected devices by a remote control unit

This completes the basic settings and operations. For details on how to change settings or detailed explanations of operations, see the included CD-ROM (Owner’s manual).

SAFETY PRECAUTIONS
CAUTION
RISK OF ELECTRIC SHOCK DO NOT OPEN

CAUTION:
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER- SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

• The lightning flash with the arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
• The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

WARNING:
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.

IMPORTANT SAFETY INSTRUCTIONS

1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
9. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.
10. Only use attachments/accessories specified by the manufacturer.
11. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/ apparatus combination to avoid injury from tip-over.
12. Unplug this apparatus during lightning storms or when unused for long periods of time.
13. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
14. Batteries shall not be exposed to excessive heat such as sunshine, fire or the like.

CAUTION:
To completely disconnect this product from the mains, disconnect the plug from the wall socket outlet. The mains plug is used to completely interrupt the power supply to the unit and must be within easy access by the user.

NOTES ON USE
WARNINGS

• Avoid high temperatures. Allow for sufficient heat dispersion when installed in a rack.
• Handle the power cord carefully. Hold the plug when unplugging the cord.
• Keep the unit free from moisture, water, and dust.
• Unplug the power cord when not using the unit for long periods of time.
• Do not obstruct the ventilation holes.
• Do not let foreign objects into the unit.
• Do not let insecticides, benzene, and thinner come in contact with the unit.
• Never disassemble or modify the unit in any way.
• Ventilation should not be impeded by covering the ventilation openings with items, such as newspapers, tablecloths or curtains.
• Naked flame sources such as lighted candles should not be placed on the unit.
• Observe and follow local regulations regarding battery disposal.
• Do not expose the unit to dripping or splashing fluids.
• Do not place objects filled with liquids, such as vases, on the unit.
• Do not handle the main cord with wet hands.
• When the switch is in the OFF (STANDBY) position, the equipment is not completely switched off from MAINS.
• The equipment shall be installed near the power supply so that the power supply is easily accessible.

DECLARATION OF CONFORMITY
We declare under our sole responsibility that this product, to which this declaration relates, is in conformity with the following standards: EN60065, EN55013, EN55020, EN61000-3-2 and EN61000-3-3. Following the provisions of Low Voltage Directive 2006/95/EC and EMC Directive 2004/108/EC, the EC regulation 1275/2008 and its framework Directive 2009/125/EC for Energy-related Products (ErP)

A NOTE ABOUT RECYCLING
This product’s packaging materials are recyclable and can be reused. Please dispose of any materials in accordance with the local recycling regulations. When discarding the unit, comply with local rules or regulations. Batteries should never be thrown away or incinerated but disposed of in accordance with the local regulations concerning battery disposal. This product and the supplied accessories, excluding the batteries, constitute the applicable product according to the WEEE directive.

Cautions on installation

• For proper heat dispersal, do not install this unit in a confined space, such as a bookcase or similar enclosure.
  • More than 0.3 m is recommended.
  • Do not place any other equipment on this unit.

www.denon.com
D&M Holdings Inc. Printed in China 5421 10054 002D

References

• denon.com
• Manual-Hub.com – Free PDF manuals!

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>