DISPLAYS2GO PLB-M0522 TV Ceiling Mount Instruction Manual

DISPLAYS2GO PLB-M0522 TV Ceiling Mount

CAUTION : DO NOT EXCEED RATED LISTED WEIGHT. SERIOUS INJURY OR PROPERTY DAMAGE MAY OCCUR

NOTE : Read the entire instruction manual before you start installation and assembly.

WARNING

• Do not begin the installation until you have read and understood all the instructions and warnings contained in this installation sheet. If you have any questions regarding any of the instructions or warnings, please contact your local distributor.
• This mounting bracket was designed to be installed and utilized ONLY as specified in this manual. Improper installation of this product may cause damage or serious injury.
• This product should only be installed by someone with good mechanical ability who has basic building experience and fully understands this manual.
• Make sure that the supporting surface will safely support the combined weight of the equipment and all attached hardware and components.
• Always use an assistant or mechanical lifting equipment to safely lift and position the equipment.
• Tighten screws firmly, but do not over-tighten. Over-tightening can cause damage to the items, This greatly reduces their holding power.
• This product is intended for indoor use only. Using this product outdoors could lead to product failure and personal injury.
• Please do not disassemble or change the electronic components of the product without authorization.

Component Checklist

IMPORTANT : Ensure that you have received all parts according to the component checklist prior to installation.
If any parts are missing or faulty, telephone your local distributor for a replacement.

Package M

PackageW

For Wooden Ceiling Mounting

WARNING

• Installers are responsible for providing hardware for other types of mounting situations.
• Installers must verify that the supporting surface will safely support the combined weight of the equipment and all attached hardware and components.

For Solid Brick and Concrete Ceiling Mounting

WARNING
Installers must verify that the supporting surface will safely support the combined weight of the equipment and all attached hardware and components.

Installing the VESA Plate

For Flat Back Screens For Recessed Back Screens or to Access AN Inputs

Note : Choose the appropriate screws, washers and spacers (if necessary) according to the type of screen.

• Screw the VESA plate onto the TV.
• Position the VESA plate as close as possible to the middle of the screen.

Tighten all screws but do not over-tighten.

Hooking the TV onto the Ceiling Mount

Installing the Decorative Covers and Running the Cables

Anything Is not allowed to pass through the mount motion space.
Use the cable ties to hold the cables in place.
Note : Leave slack in the cables for arm movement.

Placing the IR Receiver

warning

• Do not plug into the power outlet until it is ready to be operated.
• Peel the backing paper. Place the IR receiver into the desired position.
• Make sure nothing will obstruct the transmission from where the TV will be viewed.

The Remote Control Operating Instructions

Remote control operation instructions

NOTE : No-load running prohibited.
STEP 1 : When powered, the buzzer sounds once beep, and the TV ceiling mount will be in the standby state. The TV ceiling mount is installed on a flat surface by default and has an O’ -75′ continuous adjustable tilt. (Please reset the lilt angle if you install the TV ceiling mount on a pitched surface. Press and hold for 5 seconds and repeat four times. The system will automatically find the position without human intervention. Once this is done, the system will automatically stop at the maximum position. Please Ignore this step If this mount Is not Intended for installation on a pitched surface.)
STEP 2: Press and release to return the TV ceiling mount flat against the ceiling surface and hear one beep from the buzzer, the system will then enter a working condition.

Buttons function instructions

Follow the Key function instructions below to operate ****

Manual mode

• In any position (but the minimum position against the ceiling), when manually pushing up the TV ceiling mount over a distance. The TV ceiling mount will automatically return to the minimum position against the ceiling.
• In the minimum position, when manually push up the TV ceiling mount over a little distance. The TV ceiling mount will automatically unfold at the maximum position.

LEARN MODE operation instructions
The loss of a matched remote control would result in the TV ceiling mount being unusable. The LEARN MODE is used to learn how to use a TV remote (ONLY suitable for the TV remote of popular brands.) to control TV ceiling mount.

Note:

• TV remote can’t replace the all functions Of the matched remote control. Only LEARNING the three buttons functions. With and respectively.
• The user must follow the rules below when using the TV remote to control the TV ceiling mount. Select the alternate buttons from the TV remote and the button that can’t directly control the TV
• If you need to erase all the button functions LEARNED, press and hold for 4 seconds and repeat five times. If you don’t erase them, the new button functions LEARNED every time will overwrite the last button functions LEARNED

LEARN MODE instructions as shown below:

• STEP 1: Press and hold for 5 seconds until the LED light on the matched remote control stays on, and then press The buzzer will sound once, the red LED light on the IR receiver will stay on, then the LEARN MODE will be entered. STEP 2: If LEARN   please press on the matched remote control until the buzzer sounds twice, the red LED light on the IR receiver will change from being steady to a slow flash.
• STEP 3: Aim the TV remote at the IR receiver, and press the button on the TV remote that you need to set as the function Of button until the buzzer sounds three times. the red LED light on the IR receiver will change from a slow flash to a fast flash.
• STEP 4: Press the button on the matched remote control until the buzzer sounds four times. The red LED light on the IR receiver will turn Off . The button will be LEARNED successfully. If the buzzer only sounds once, then a LEARN failure. (The TV remote won’t support the LEARNING function) (Please follow step through step4 in turn if the user needs to LEARN more buttons.)

Learn the “Power” button on the TV remote:

• Press and hold for 5 seconds until the LED light on the matched remote control stays on, and then press .
• The buzzer will sound once, the red LED light on the IR receiver will stay on, then press and hold button on the matched remote control until the buzzer sounds twice, then release the button. The red LED light on the IR receiver will change from being steady to a slow flash.
• Aim the TV remote at the IR receiver, and press the “Power” button. The buzzer will sound three times. The red
• The LED light on the IR receiver will change from a slow flash to a fast flash. Press button on the matched remote control until the buzzer sounds four times. The red LED light on the IR receiver will turn off. The “Power” button will be LEARNED successfully. If press the “power” button, the TV wall mount will automatically reset.

Note : When there is no activity for over 20 seconds in any step.TV remote will automatically exit from the LEARN MODE.

Maintenance

• Check that the bracket is secure and safe to use at regular intervals(at least every three months).
• Please contact your distributor if you have any questions.

References

• Manual-Hub.com – Free PDF manuals!

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>