D-LINK DWL-2700AP Access Point Command Line Interface Reference User Manual

D-LINK DWL-2700AP Access Point Command Line Interface Reference

Product Information

Product Name: DWL-2700AP

Product Type: 802.11b/g Access Point

Manual Version: Ver 3.20 (February 2009)

Recyclable: Yes

User Manual: https://manual-hub.com/

Specifications

• Supports 802.11b/g wireless standard
• Command Line Interface (CLI) for configuration and management
• Telnet access for remote management
• No initial password required for login

Product Usage Instructions

Accessing the CLI

The DWL-2700AP can be accessed using Telnet. Follow these steps to access the CLI:

1. Open the Command Prompt on the computer that will be used for configuration and management.

2. Enter the command telnet <AP IP address>.
   For example, if the default IP address is 192.168.0.50, enter telnet 192.168.0.50.

3. A login screen will appear. Enter the username asadmin and press Enter.

4. No initial password is required, so press Enter again.

5. You have successfully logged into the DWL-2700AP.

Using the CLI

The CLI provides several helpful features. To view the available commands, enter ? or help and press Enter.

If you enter a command without all its required parameters, the CLI will prompt you with a list of possible completions. For example, if you enter tftp, a screen will display all possible command completions for tftp.

When a command requires a variable or value that needs to be specified, the CLI will provide further information. For example, if you enter snmp authtrap, the missing value (enable/disable) will be displayed.

Command Syntax

The following symbols are used to describe command entries and specify values and arguments:

• <>: Encloses a variable or value that must be specified. Example: set login <username>
• []: Encloses a required value or set of required arguments. Example: get multi-authentication [index]
• :: Separates mutually exclusive items in a list, one of which must be entered.

Frequently Asked Questions

Q: How can I access the DWL-2700AP Command Line Interface?

A: You can access the CLI by using Telnet and entering the IP address of the DWL-2700AP in the Command Prompt.

Q: What is the default username and password for accessing the CLI?

A: The default username is admin, and no initial password is required.

DWL-2700AP
802.11b/g Access Point
Command Line Interface Reference Manual

Ver 3.20 (Feberuary 2009)

RECYCLABLE

USING THE CLI

The DWL-2700AP can be accessed by Telnet. Using Microsoft Windows Operation system as example, open the Command Prompt on the computer that will be used for configuring and managing the AP and enter telnet and IP address of DWL- 2700AP in the first line. Using the default IP address as example, enter telnet 192.168.0.50 to cause the following screen to open:

Press Enter in the screen above. The following screen opens:

Type “admin” for the D-Link Access Point login username in the screen above and press Enter. The following screen opens:

Press Enter as there is no initial password.
The following screen opens to indicates you have successfully logged into the DWL-2700AP.

Commands are entered at the command prompt, D-Link Access Point wlan1 – >

There are a number of helpful features included in the CLI. Entering the “?” command and then pressing Enter will display a list of all of the top-level commands. The same information can also be displayed by entering “help”.

Press Enter to see a list of all the available commands. Alternatively, you may enter “help” and the press Enter.

When you enter a command without all of its required parameters, the CLI will prompt you with a list of possible completions. For example, if “tftp” was entered, the following screen opens:

This screen displays all the possible command completions for “tftp” When you enter a command without a variable or value that needs to be specified, the CLI will prompt you with further information about what is needed to complete the command. For example, if “snmp authtrap” was entered, the following screen opens:

The missing value for the “snmp authtrap” command, “enable/disable,” is displayed in the screen above.

COMMAND SYNTAX

The following symbols are used to describe how command entries are made and values and arguments are specified in this manual. The online help contained in the CLI and available through the console interface uses the same syntax.

Note: All commands are case-insensitive.

< angle brackets>

Purpose| Encloses a variable or value that must be specified.
Syntax| set login
Description| In the above syntax example, you must specify the username. Do not type the angle brackets.
Example Command| set login accounting
[square brackets]

Purpose| Encloses a required value or set of required arguments. One value or argument can be specified.
Syntax| get multi-authentication [index]
Description| In the above syntax example, you must specify an index to be created. Do not type the square brackets.
Example Command| get multi-authentication 2
: colon

Purpose| Separates two or more mutually exclusive items in a list, one of which must be entered.
Syntax| set antenna [1:2:best]
Description| In the above syntax example, you must specify either 1 , 2 or

best. Do not type the colon.

Example Command| set antenna best

UTILITY COMMANDS

bdtempmode [enable:disable]
get bdalarmtemp| Display Monitor Board Temperature Alarm Limitation (In Centigrade)| get bdalarmtemp
set bdalarmtemp| Set Monitor Board Temperature Alarm Limitation (In Centigrade)| set bdalarmtemp
get bdcurrenttemp| Display Current Board Temperature (In Centigrade)| get bdcurrenttemp
set detectlightmode| Set HW Detect Light Mode| set detectlightmode [enable:disable]
Addminstration Command:| Function| Syntax
get login| Display Login User Name| get login
get uptime| Display UpTime| get uptime
set login| Modify Login User Name| set login
set password| Modify Password| set password
get wlanManage| Display manage AP with WLAN Mode| get wlanManage
set wlanmanage| Set manage AP with WLAN Mode| set wlanmanage [enable:disable]
get systemname| Display Access Point System Name| get systemname
set systemname| Specify Access Point System Name| set systemname
Other Command:| Function| Syntax
radar!| Simulate radar detection on current channel| radar!

ETHERNET   COMMANDS

Explanation:<xxx.xxx.xxx.xxx>is IP address
set ipaddr| Set IP Address| set ipaddr <xxx.xxx.xxx.xxx>

Explanation: <xxx.xxx.xxx.xxx> is IP address

set ipmask| Set IP Network/Subnet Mask| set ipmask < xxx.xxx.xxx.xxx>

Explanation: <xxx.xxx.xxx.xxx> is Network mask

set lcp| Set Lcp State| set lcp [0:1] Explanation:0=disable 1=enable
set gateway| Set Gateway IP Address| set gateway <xxx.xxx.xxx.xxx>

Explanation: <xxx.xxx.xxx.xxx>   is Gateway IP address

set dhcpc

set domainsuffix set nameaddr

__

__

set ethctrl

| Set DHCP Clinet State of enable or disabled Set Domain Name Server Suffix

Set Name Server IP Address

__

__

__

ethernet control Speed and FullDuplex

| set dhcp[disable:enable] set domainsuffix

set nameaddr [1:2] <xxx.xxx.xxx.xxx> set ethctrl[0:1:2:3:4]

Explanation:

0:  Auto

1:  100M       FullDuplex

2:  100M       HalfDuplex

3:  10M         FullDuplex

4:  10M         HalfDuplex

WIRELESS   COMMANDS

Fundamental

Config Commands:| Function| Syntax
config wlan| Select WLAN Adapter to configure. DWL-2700AP only WLAN 1 is available for configuration. This command is not necessary.| config wlan [0:1]
Find Commands:
find bss| Perform Site Survey, Wireless service will be disrupted| find bss
find channel| Channel spanning to select the Preferred Channel| find channel
find all| Perform Site Survey including Super G and Turbo, Wireless service will be disrupted| find all
find rogue| Find Rogue BSS| find rogue
Get Command:| Function| Syntax
get apmode| Display current AP Mode| get apmode
get ssid| Display Service Set ID| get ssid
get ssidsuppress| Display SSID Suppress Mode is enabled or disabled| get ssidsuppress
get station| Display Client Station Connection Status| get station
get wdsap| Display WDS Access Point List| get wdsap
get remoteAp| Display Remote AP’s Mac Address| get remoteAp
get association| Display Association Table that indicates the information of associated client devices| get association
get autochannelselect| Display state of Auto Channel Selection feature (enabled, disabled)| get autochannelselect
get channel| Display Radio Frequency (MHz) and Channel Designation| get channel
get availablechannel| Display available Radio channels| get availablechannel
get rate| Display current Data Rate selection.  Default is best.| get rate
get beaconinterval| Display Beacon Interval| get beaconinterval
get dtim| Display Delivery Traffic Indication Message Beacon Rate| get dtim
get fragmentthreshold| Display Fragment Threshold in bytes| get fragmentationthreshold
get rtsthreshold| Display RTS/CTS Threshold| get rtsthreshold
get power| Display Transmit Power Setting:    Full, half, quarter, eighth, min| get power
get wlanstate| Display Wireless LAN state status (enabled or disabled)| get wlanstate
get shortpreamble| Display Short Preamble Usage state: enabled or disabled| get shortpreamble
get wirelessmode| Display Wireless LAN Mode (11b or 11g)| get wirelessmode
get 11gonly| Display 11g Only Mode operational state of enabled or disabled| get 11gonly
---|---|---
get antenna| Display Antenna Diversity of 1, 2, or best| get antenna
get sta2sta| Display wireless STAs to wireless STAs connect state| get sta2sta
get eth2sta| Display ethernet to wireless STAs connect state| get eth2sta
get trapsevers| Get trap server state| get trapsevers
get eth2wlan| Display Eth2Wlan Broadcast packet filter state| get eth2wlan
get macaddress| Display Mac Address| get macaddress
get config| Display Current AP Configuration Settings| get config
get countrycode| Display Country Code setting| get countrycode
get hardware| Display Hardware Revisions of WLAN Components| get hardware
get aging| Display Aging Interval in seconds| get aging
get MulticastPacketControl| Display Multicast Packet Control state| get MulticastPacketControl
get MaxMulticastPacketNumber| Display Max Multicast Packet Number| get MaxMulticastPacketNumber
get 11goptimize| Display 11g Optimization Level| get 11goptimize
get 11goverlapbss| Display Overlapping BSS Protection| get 11goverlapbss
get assocnum| Display Number Of Association STA| get assocnum
get eth2wlanfilter| Display Eth2WLAN BC & MC filter type| get eth2wlanfilter
get extendedchanmode| Display Extended Channel Mode| get extendedchanmode
get iapp| Display IAPP State| get iapp
get iapplist| Display IAPP Group List| get iapplist
get iappuser| Display IAPP User Limit Number| get iappuser
get minimumrate| Display Minimum Rate| get minimumrate
get dfsinforshow| Display DFS infor| get dfsinforshow
get wdsrssi| Display WDS Access Point RSSI| get wdsrssi
get ackmode| Display Variable Ack Time Mode| get ackmode
get acktimeout| Display Ack Time Out Number| get acktimeout
Set Command:| Function| Syntax
set apmode| Set AP Mode to Normal AP, WDS with AP Mode,WDS without AP Mode or AP Client| set apmode [ap:wdswithap:wds:apc]
set ssid| Set Service Set ID| set ssid
set ssidsuppress| Set SSID Suppress Mode enable or disable| set ssidsuppress [disable:enable]
set autochannelselect| Set Auto Channel Selection to enable or disable| set autochannelselect [disable:enable]
set rate| Set Data Rate| set rate [best:1:2:5.5:6:9:11:12:18:24:36:48:54]
set beaconinterval| Modify Beacon Interval 20-1000| set beaconinterval [20-1000]
set dtim| Set Delivery Traffic Indication Message Beacon Rate.  Default is 1| set dtim [1-255]
---|---|---
set fragmentthreshold| Set Fragment Threshold| set fragmentationthreshold [256-2346]
set rtsthreshold| Set RTS/CTS Threshold in bytes| set rtsthreshold [256-2346f]
set power| Set Transmit Power in predefined increments| set power [full:half:quarter:eighth:min]
set roguestatus| Set Rogue AP status| set roguestatus [enable:disable]
set roguebsstypestatus| Set Rogue AP BSS type status| set roguebsstypestatus [enable:disable]
set roguebsstype| Set ROGUE AP BSS Type| set roguebsstype [apbss:adhoc:both’]
set roguesecuritystatus| Set Rogue AP Security Type status| set roguesecuritystatus [enable: disable]
set roguesecurity| Set ROGUE AP Security Type| set roguesecurity
set roguebandselectstatus| Set Rogue AP Band Select status| set roguebandselectstatus [enable:disable]
set roguebandselect| Set ROGUE AP Band Select| set roguebandselect
set wlanstate| Select the operational state of wlan:    enabled or disabled| set wlanstate [disable:enable]
set shortpreamble| Set Short Preamble| set shortpreamble [disable: enable]
set wirelessmode| set wirelessmode to 11b/11g.| set wirelessmode [11a:11b:11g] NOTE:11a is not supported.
set 11gonly| Only 802.11g clients will be Allowed to connect to this BSS| set 11gonly [disable:enable]
set antenna| Set Antenna selection of 1, 2, or best| set antenna [1:2:best]
set aging| Set Aging Interval| set aging
set channel| Select Radio Channel of Operation| set channel [1:2:3:4:5:6:7:8:9:10:11]
set eth2wlan| Enable or Disable the Eth2Wlan Broadcast packet filter feature| set eth2wlan  [0:1]

Explanation: 0=disable:1=enable

set sta2sta| Set wireless STAs to wireless STAs connect state (WLAN Partition)| set sta2sta [disable: enable]
set eth2sta| Set ethernet to wireless STAs connect state| set eth2sta [disable: enable]
set trapsevers| Set trap server state| set trapsevers [disable:enable]
set MulticastPacketControl| Enable or Disable Multicast Packet Control| set MulticastPacketControl [0:1] Explanation: 0=disable:1=enable
set MaxMulticastPacketNumber set extendedchanmode

set eth2wlanfilter set ackmode

set acktimeout

set iapp

set iappuser

| Set Max Multicast Packet Number Set Extended Channel Mode

Set Eth2WLAN Broadcast & Multicast Filter type

__

Set Ack Mode

Set Ack Timeout Number Set IAPP State.

Set IAPP User Limit Number

| set MaxMulticastPacketNumber [0-1024]

set extendedchanmode [disable:enable] set eth2wlanfilter [1:2:3]

Explanation: 1=Broadcast filter: 2=Multicast filter: 3=Both of BC and

MC.

set ackmode [enable:disable] set acktimeout

set iapp [0:1]

Explanation: 0=close 1=open

set iappuser [0-64]

Security

Del Command:| Function| Syntax
del key| Delete Encryption key| del key [1-4]
Get Command:| Function| Syntax
get encryption| Display (WEP) configuration state (enabled or disabled)| get encryption
get authentication| Display Authentication Type| get authentication
__

__

get cipher

| Display Encryption cipher type Explanation:

Response WEP for choosing WEP Response Auto for choosing WPA-Auto Resopnse AES for choosing WPA-AES

Response TKIP for choosing WPA-TKIP

| __

__

get cipher

__

__

get keysource

| Display Source Of Encryption Keys: Explanation:

Response Flash Memory for static key Response Key Server for dynamic key

Response mixed for mix static and dynamic key

| __

__

get keysource

get key| Display specified WEP encryption Key| get key [1-4]
get keyentrymethod| Display Encryption Key Entry Method ASCII or Hexadecimal| get keyentrymethod
get groupkeyupdate| Display WPA Group Key Update Interval (in Seconds)| get groupkeyupdate
get defaultkeyindex| Display Active Key Index| get defaultkeyindex
get dot1xweptype| Display 802.1x Wep Key Type| get dot1xweptype
get reauthperiod| Display Manual Reauthentication Period| get reauthperiod
Set Command:| Function| Syntax
set encryption| Enable or Disable Encryption Mode| set encryption [disable: enable]
set authentication| Set Authentication Type| set authentication [open-system: shared-key: auto:8021x: WPA: WPA-PSK: WPA2: WPA2-PSK:WPA-AUTO:WAP2-AUTO-PSK]
set cipher| Set Cipher of wep, aes, tkip, or auto negotiate| set cipher [wep:aes:tkip:auto]
set groupkeyupdate| Set Group Key Update Interval (in Seconds) for TKIP| set groupkeyupdate
set key| Used to set the specified wep key value and size| set key [1-4] default

set key [1-4] [40:104:128] < value>

set keyentrymethod| Select Between ASCII or HEX encryption key format| set keyentrymethod [asciitext : hexadecimal]
set keysource| Select Source of Encryption Keys: static(flash), dynamic (server), mixed| set keysource [flash:server:mixed]
set passphrase set dot1xweptype

set reauthperiod

| Modify Passphrase

Set 802.1x Wep Key Type

Set Manual Reauthentication Period

| set passphrase set dot1xweptype [static: dynamic] set reauthperiod

Explanation: is new priod.

WMM

Get Command:| Function| Syntax
get wmm| Display WMM mode status  (enabled or disabled)| get wmm
get wmmParamBss| Display WMM parameters used by STA in this BSS| get wmmParamBss
get wmmParam| Display WMM parameters used by this AP| get wmmParam
Set Command:| Function| Syntax
set wmm| Enable or Disable WMM Features| set wmm [disable:enable]
__

__

__

set wmmParamBss ac

| __

__

__

Set WMM (EDCA) parameters used by STAs in this BSS

| set wmmParamBss ac [AC number] [logCwMin] [logCwMax] [aifs] [txOpLimit] [acm]

Explanation:

AC number: 0->AC_BE

1- >AC_BK

2- >AC_BK

3- >AC_BK

Exampble:

set wmmParamBss ac 0 4 10 3 0 0

__

__

set wmmParam ac

| __

__

Set WMM (EDCA) parameters used by this AP

| set wmmParamBss ac [AC number] [logCwMin] [logCwMax] [aifs] [txOpLimit] [acm] [ack-policy]

Explanation:

AC number: 0->AC_BE

1- >AC_BK

2- >AC_BK

3- >AC_BK

MULTI-SSID AND VLAN COMMANDS

state
get multi-ind-state [index]| Display Individual Multi-SSID State| get multi- ind-state [index]
get multi-ssid [index]| Display SSID of the specify Multi-SSID| get multi-ssid [index]
get multi-ssidsuppress [index]| Display SSID Suppress Mode of the specify Multi-SSID| get multi-ssidsuppress [index]
get multi-authentication [index]| Display Authentication Type for Multi-SSID| get multi-authentication [index]
get multi-cipher [index]| Display Encryption cipher for Multi-SSID| get multi- cipher [index]
get multi-encryption [index]| Display Encryption Mode for Multi-SSID| get multi-encryption [index]
get multi-keyentrymethod| Display Encryption Key Entry Method for Multi-SID| get multi-keyentrymethod
get multi-vlantag [index]| Display Vlan tag for Multi-SSID| get multi-vlantag [index]
get multi-key [index]| Display Encryption Key for Multi-SSID| get multi-key [index]
get multi-keysource [index]| Display Key Source for Multi-SSID| get multi- keysource [index]
get multi-config [index]| Display AP Configuration for Multi-SSID| get multi- config [index]
get multi-passphrase [index]| Display Passphrase for Multi-SSID| get multi- passphrase [index]
get multi-dot1xweptype [index]| Display 802.1x Wep Key Type For Multi-SSID| get multi-dot1xweptype [index]
Set Command:| Function| Syntax
set vlanstate| Enable or Disable VLAN| set vlanstate [disable:enable]

Note: Must Enable Multi-SSID firstly

set vlanmanage| Set Enabled or Disable manage AP with VLAN| set vlanmanage [disable:enable] Note: Must Enable vlanstate firstly
set nativevlan| Set Native Vlan Tag| set nativevlan [1-4096]
set Vlantag| Set VLAN Tag| set vlantag
set Vlanpristate| Set Vlan Priority State| set Vlanpristate [enable:disable]
set Vlanpri| Modify Vlan Priority| set Vlanpri [0-7]
set ethnotag| Set Primary Eth No Tag Stat| set ethnotag [enable:disable]
set multi-vlantag| Set VLAN Tag for Multi-SSID| set multi-vlantag [index]
set multi-ethnotag| Set Individual Eth No Tag State| set multi-ethnotag [index] [disable:enable]
---|---|---
set multi-vlanpri| Set Vlan-Priorityi for Multi-SSID| set multi-vlanpri [pri value] [index]
set VlantagType| Modify Vlantag Type| set VlantagType [1:2]
set multi-vlantagtype| Set Vlan-Tag Typefor Multi-SSID| set multi-vlantagtype [tagType value] [index]
set multi-state| Enable or Disable Multi-SSID Features| set multi-state [disable:enable]
set multi-ind-state| Enable or Disable specifically Mulit-SSID| set multi-ind- state  [disable:enable] [index]
set multi-ssid| Set Service Set ID for Multi-SSID| set multi-ssid  [index]