MOMAN H2 Pro Headset Helmet Intercom User Manual
- June 17, 2024
- MOMAN
Table of Contents
MOMAN H2 Pro Headset Helmet Intercom User Manual
INSTALLTION INSTRUCTION
Caring For Your MOMAN Product
- Please keep the product in a dry, clean, dust-free environment.
- Keep corrosive chemicals, liquids and heat source away from the product to prevent mechanics damage.
- Use only a soft and dry cloth for cleaning the product.
- Malfunction may be caused by dropping, impact of external force.
- Do not attempt to disassemble the product. Doing so voids warranty.
- Please have the product checked or repaired by authorized technicians if any malfunctions happened.
- Failure to follow all the instructions may result in mechanics damage.
- Warranty does not apply to human errors.
Package List
Product Introduction
- On/Off Key
- Knob
- Headset Interface
- Headset Plug
- Indicator Light
- Function Key
- Buckle Flap
- Charging Interface
- Speaker
- Butterfly sticker
- Replaceable hard mic
- Replaceable soft mic
Important Notice:
Before installing the headsets, follow the Quick Manual instructions to
connect your phone and audition the sound and volume. If there is a large
difference in sound effect and volume after installing it on the helmet,
please adjust the position of the speaker in the helmet.
Operation
Power On/Off
ON: Press the ON/OFF key for 2 seconds.
OFF: Long Press the ON/OFF key for 4 seconds.
Reset: Under Power on mode, long Press the ON/OFF Key for 8 seconds.
Phone Control
Music Control
There is voice alarm for too high and too low volume.
FM Radio
ON: Under Standby mode, double-click the Function Key twice.
OFF: Double-click the function key twice.
3 Select channels: Quickly ratate and release the knob to select and adjust
Notes:
If the signal is weak indoor, you could try to turn on the FM radio near
window or in the open area
When FM radio is turned on and there is a phone calling, the machine will cut
off FM radio automatically and connect to the mobile phone. It gets back to
the FM radio when the call ends.
Language Switch
Power on, press the ON/OFF key and ratate the knob at the same time. (English
Japanese → Italian)
Voice Assistant
Pairing and Disconnetion
With Mobile Phone:
After switching on press the On/Off Key and Function Key simultaneously for 4
seconds, BLUE light flashes twice, then RED and BLUE light flash
alternatively, Pairing Turn on the bluetooth function search “MOMAN H2 PRO to
connect.
Voice prompt “Bluetooth connected
MOMAN H2 PRO Connected
After switching on, press the On/Off Key and Function Key simultaneously for 4
seconds. BLUE light flashes twice, then RED and BLUE light flash alternatively
2 Press the ON/OFF key of 1 intercom, the blue indicatior light flashes
After switching on, press the On/Off Key and Function Key simultaneously for 4
seconds. BLUE light flashes twice, then RED and BLUE light flash alternatively
2 Press the ON/OFF key of 1 intercom, the blue indicatior light flashes
Music Sharing
ON:
OFF : Press the Function Key of Intercom A for 2 seconds 9. Multi-Mode Switch Between Intercom and Musci/FM Radio
. Method 1: Install with Back Clip
1 Use the screwdriver to loosen the screws of the back clip so that it can
open to a proper extent.
Open the helmet liner, insert the clip into the right position on the left
side of the helmet and tighten the screw
Slide the intercom into the back clip slot to make sure it locks firmly
Open the helmet liner (ear position), clean the EPS surface of the heimet, and
stick a piece of horn Velcro on the left and right sides of the helmet.
5 Stick the speaker on the fixed Velcro surface and the speaker with short
line should be installed close to the machine. Fix the microphone and arrange
the helmet lining and cable
Insert the headset into the jack of the intercom and tie up the headset cable.
. Method 1: Install with Back Clip
- Use the screwdriver to loosen the screws of the back clip so that it can open to a proper extent.
- Open the helmet liner, insert the clip into the right position on the left side of the helmet and tighten the screw
- Slide the intercom into the back clip slot to make sure it locks firmly
- Open the helmet liner (ear position), clean the EPS surface of the heimet, and stick a piece of horn Velcro on the left and right sides of the helmet.
- Stick the speaker on the fixed Velcro surface and the speaker with short line should be installed close to the machine. Fix the microphone and arrange the helmet lining and cable
- Insert the headset into the jack of the intercom and tie up the headset cable.
Method 2: Install with Velcro Clip Separate the hook and loop fasteners. First stick the hook onto the Velcro clip; choose the right installation position on the helmet and stick the loop to the position. Install the intercom onto the Velcro clip The installation of speakers can refer to the description above.
Installation
-
Before using the Bluetooth intercom, please use the attached charging cable to charge the intercom. The small type-C interface on the charging line is connected to the USB charging interface of the Bluetooth intercom, and the large USB connector on the charging cable is connected to the following charging interface for power supply: N 1.the 2. st Se USB interface of computer;
B. A mobile power supply with DC 5V output;
C. A USB power adapter with DC 5V output. -
When charging, the red LED is always on, and when fully charged, the red light goes out slowly. It takes up to 2.5 hours to fully charge the unit.
Notes
-
If you do not use intercom for up to one month or more, please charge the intercom once every two months in order to protect the lithium battery;
-
The storage temperature of this product is -20°C to 50 °C, and do not store in the environment with too high or low temperature, otherwise, the service life of the product will be affected;
-
Do not expose this product to fire to avoid explosion:
-
Only two screws on the back of intercom can be opened. Do not open other screws to the intercom to avoid short circuit of main board or battery damage.
-
Language Switch
Power on, press the ON/OFF key and ratate the knob Japanese Italian)
at the same time. (English OMOWAN HOMAN Voice Assistant -
Pairing and Disconnetion
With Mobile Phone:
After switching on, press the On/Off Key and Function Key simultaneously for 4 seconds, BLUE light flashes twice, then RED and BLUE light flash alternatively.
② Pairing: Turn on the bluetooth function search “MOMAN H2 PRO” to connect.
Two Intercoms Pairing
- After switching on press the On/Off Key and Function Key simultaneously for 4 seconds, BLUE light flashes twice, then RED and BLUE light flash alternatively.
- Press the ON/OFF key of 1 intercom, the blue indicatior light flashes quickly.
Notes:
- Automatic connection: Once the intercoms pair successfully, there is no need to pair repeatedly.
- After switching on, short press the On/Off Key under Standby mode to repair.
Reconnect &Disconnect
-
Reconnect : Short press the ON/OFF Key Voice prompt: “Di”.
-
Disconnec : Short press the ON/OFF Key Voice prompt: “Di”.
Notes:
Within five minutes of disconnection, connects automatically:
More than five minutes, short press the On/Off Key to search.
Music Sharing
ON
OFF: Press the Function Key of Intercom A for 2 seconds
Multi-Mode Switch
Between Intercom and Musci/FM Radio:
Moman (UK) Limited
Between Intercom and Mobile Phone:
10. Funcition Priority Level
- Mobile Phone Level
- Intercom Level
- Music/FM Radio
Installation
Method 1: Install with Back Clip
-
Use the screwdriver to loosen the screws of the back clip so that it can open to a proper extent.
-
Open the helmet liner, insert the clip into the right position on the left side of the helmet and tighten the screw.
-
Slide the intercom into the back clip slot to make sure it locks firmly.
-
Open the helmet liner (ear position), clean the EPS surface of the helmet, and stick a piece of horn Velcro on the left and right sides of the helmet.
-
Stick the speaker on the fixed Velcro surface and the speaker with short line should be installed close to the machine. Fix the microphone and arrange the helmet lining and cable.
-
Insert the headset into the jack of the intercom and tie up the headset cable.
Method 2: Install with Velcro Clip
Separate the hook and loop fasteners. First stick the hook onto the Velcro
clip; choose the right installation position on the helmet and stick the loop
to the position. Install the intercom onto the Velcro clip. The installation
of speakers can refer to the description above.
How to Remove the Intercom from Helmet
First unplug the headset, then press the fixed buckle in the middle of the
back clip with one finger (push towards the side of the helmet), so that the
back clip hook is detached from the intercom, and push the intercom upwards to
let it slide out of the back clip smoothly to complete the disassembly.
How to Fix the Headset Plug (If necessary)
Unscrew the screws on the back of intercom with screwdriver, open the buckle
flap, plug in the headset plug and tighten the screws. If you need to plug out
the headset, please open the buckle flap by unscrewing the screws.
Installation
-
Before using the Bluetooth intercom, please use the attached charging cable to charge the intercom. The small type-C Interface on the charging line is connected to the USB charging interface of the Bluetooth intercom, and the large USB connector on the charging cable is connected to the following charging interface for power supply:
A. USB Interface of computer;
B. A mobile power supply with DC 5V output;
C. A USB power adapter with DC 5V output -
When charging, the red LED is always on, and when fully charged, the red light goes out slowly. It takes up to 2.5 hours to fully charge the unit.
Notes
- If you do not use intercom for up to one month or more, please charge the Intercom once every two months in order to protect the lithium battery;
- The storage temperature of this product is -20 ℃ to 50°C, and do not store in the environment with too high or low temperature, otherwise, the service life of the product will be affected,
- Do not expose this product to fire to avoid explosion,
- Only two screws on the back of intercom can be opened. Do not open other screws to the intercom to avoid short circuit of main board or battery damage.
Unit 25 Basepoint Business Centre, Aviation Park, West Christchurch, United
Kingdom BH23 6NX
www.momanx.com
MomanGlobal
https://moman.co/youtube
