LOUROE ELECTRONICS MS-1 Mute Switch Instruction Manual

June 17, 2024
LOUROE ELECTRONICS

6955 VALJEAN AVE, VAN NUYS, CA 91406
PH: (818)994-6498 / FAX: (818)994-6458
techsupport@louroe.com / www.louroe.com
MS-1
MUTE SWITCH
INSTALLATION AND OPERATING INSTRUCTIONS

LOUROE ELECTRONICS MS 1 Mute Switch-

DESCRIPTION

The MS-1 Mute Switch is an accessory to Louroe Audio Monitoring/Audio Surveillance Systems when microphone muting is required. The MS-1 contains a built-in rocker switch mounted to a single gang stainless steel face plate.
When the Top part of the rocker switch is pressed IN, the rocker switch illuminates , indicating the microphone is RED live and active. When the Lower part of the switch is pressed IN, illumination of the switch turns OFF, indicating that power to the microphone is cut off and the microphone is disabled. The MS-1 fits into a single gang backbox (not included) for mounting to a wall or flat surface.

OPERATION

A rocker switch is mounted to a single gang stainless steel face plate. Top part of switch is marked MICROPHONE ON WHEN ILLUMINATED. Lower part of switch is marked MICROPHONE OFF.
When the Top part of the rocker switch is pressed to MICROPHONE ON WHEN ILLUMINATED, the rocker switch illuminates RED, indicating that the microphone is active and will pick up sounds within it’s range.
When Lower part of the rocker switch is pressed in to MICROPHONE OFF, illumination turns OFF, indicating that the microphone is muted and no sound is produced.

WIRING CONNECTION TO LOUROE BASE STATION OR AUDIO INTERFACE ADAPTER
On the back panel of Louroe Base Station or Audio Interface Adapter is a 3-pin terminal block marked A, B, C.
A = 12Vdc
B = Audio Input
C = Ground

If using recommended or similar cable connect as follows:

  1. Red wire connects to terminal A
  2.  Black wire connects to terminal B
  3. Bare wire connects to terminal C

CONNECTION BETWEEN LOUROE BASE STATION OR AUDIO INTERFACE ADAPTER AND LOUROE MODEL MS-1
The 3-pin terminal block of the Model MS-1 has been assigned with letters A, B, C (not shown on actual board) for ease of installations.

  1. Using recommended cable connect Red wire from terminal A of base station to terminal A of MS-1
  2. Connect Black wire from terminal B of base station to terminal B of microphone. Splice the wires together using wire nut (see diagram on next page)
  3. Connect Bare wire from terminal C of base station to terminal C of MS-1.

WIRING CONNECTION FROM LOUROE MODEL MS-1 TO MICROPHONE
Using another set of recommended cable (West Penn 452 or equivalent) connect as follows:

  1. Connect terminal B of MS-1 to terminal A of microphone
  2. Connect terminal C of MS-1 to terminal C of microphone.
  3. Connect terminal B of the microphone to terminal B of base station or audio interface adapter using wire nut (mentioned previously).

INTERCONNECTION DIAGRAM FOR MS-1 MUTE SWITCH, LOUROE MICROPHONE AND LOUROE AUDIO BASE STATION OR AUDIO INTERFACE ADAPTER

LOUROE ELECTRONICS MS 1 Mute Switch- drain wire1

APPLYING POWER TO THE SYSTEM

After all wiring between the base station or audio interface, microphone and MS-1 Mute Switch is complete, apply power with the power supply, (included) with the APR-1 Base Station or audio interface.

  1. First connect small end of 12Vdc Power Supply to the 12Vdc Power Jack[10], then plug power block into a standard 120Vac wall outlet or power strip.
  2. Turn “ON” power to APR-1 by rotating the Power-Volume Knob[1] clockwise. Adjust volume of audio by rotating the knob either clockwise to increase or counterclockwise to decrease.
  3. The APR-1 will power up both the remote microphone and the MS-1 Mute Switch

CONNECTING MICROPHONE DIRECTLY TO A RECORDER
The microphone maybe connected directly to a recorder without the use of an interface adapter or base station

  1. Connect +12Vdc power supply to terminals “A” and “C” of the MS-1. Connect +12 Vdc to terminal “A” and -12Vdc or ground to terminal “C”.
  2.  Connect terminal “B” of MS-1 to terminal “A” of of microphone (shown in drawing).
  3.  Connect terminal “C” of MS-1 to terminal “C” of microphone.
  4. Run 2 wires from the microphone to the recorder
    a. Connect terminal “B” of microphone to the positive tip of the 3.5mm mono or .RCA plug (this plugs to the recorder input)
    b. Connect terminal “C” of microphone to the negative or ground of the 3.5mm mono or RCA plug

LOUROE ELECTRONICS MS 1 Mute Switch- Rocker Switch
Positioning

TESTING AND OPERATION OF SYSTEM

Make sure the Microphone is active. Top part of MS-1 switch must be pressed IN and the Red Rocker Switch illuminated.

  1. Create some sound (radio, someone speaking, etc) near the microphone. The sounds will transmit to the APR-1’s built-in speaker[9] (see page 6). Adjust the volume of audio by rotating the volume knob clockwise to increase, or counterclockwise to decrease.
  2. To mute the system, press the lower part of the rocker switch IN. The lighted switch will go dark, indicating power if OFF and the microphone is DISABLED.
  3.  Again create some sound. There should be no transmission of audio through the base station (APR-1, etc).
  4. If the microphone is directly connected to a recorder, turn ON the recorder to record the audio from the microphone

R ECORDING AUDIO AND AUDIO PLAYBACK
If live audio is to be recorded, connect an RCA patch cable to “Audio Out” of Louroe™ Base Station[12] (see page 7) or audio interface adapter to “Audio In” of the recording device (DVR, VCR, etc.)
AUDIO PLAYBACK
For receiving audio playback through the APR-1 Base Station, connect an RCA cable from “Audio Out” of the DVR, VCR, etc. to “Audio In” [11] (see page 7) of the APR-1. Press the “Audio Playback” Switch of the recording device, then press “Push for Playback” Switch [7] of the APR-1 Base Station. Audio playback will be channeled through the APR-1 Speaker [9]

SPECIFICATIONS OF MS-1 MUTE SWITCH

Supply Voltage 12Vdc
Dimensions 2 ¾  W x
Faceplate 303 Stainless Steel
Backbox Single gang electrical box (not included)
Weight, net 2.5 oz (71g)

LOUROE ELECTRONICS MS 1 Mute Switch- FRONT PANEL

[1]| Power-Volume| Turns “ON” power to the unit and controls the audio volume through the Speaker[9].
---|---|---
[2]| Filter OUT Indicator| Lights (green) when the audio filter is not in use and the Filter Switch[6]
is in the “OUT” Position. Also indicates power to the unit.
[3]| Filter IN Indicator| Used to enhance audio playback from 24 hour time lapse recorders. Lights (orange) when filter button is pushed in.This function is no longer available with this product
[4]| Playback IN Indicator| Lights (yellow) when Push for Playback[7] is pushed in to “ON” position.
[5]| Overload Indicator| Flashes (red) when there is a short in the power supply.
[6]| Filter Switch| Normally used for audio playback from a time-lapse recorder. No longer available with this product.
[7]| Push for playback| Used for DVRNCR playback. May also be used to listen to audio from an external source. Press switch to listen to playback. Switch must be “OUT” or “OFF” when monitoring and recording, otherwise live audio is muted.
[8]| Headphone Jack| Used for private listening. Any 3.5mm stereo headphone with 8W to 600W impedance can be used.
[9]| Speaker (3″)| Provides live audio. Muted when a headphone is connected to Headphone Jack [8].

REAR PANEL LAYOUT OF APR-1

LOUROE ELECTRONICS MS 1 Mute Switch- REAR PANEL

[10]  Power Jack| Accepts 12Vdc power from Model AD-1 Power Supply
(included with APR-1 Audio Base Station).  AD-1 has a 90° 2.1mm female plug.
---|---
[11] AUDIO IN Jack (RCA)| Accepts audio playback from an external source (DVR/VCR).
Audio playback is produced through the speaker. The Push for Playback[7] must be “IN” during audio playback and “OUT” when not used for playback.
[12] AUDIO OUT Jack (RCA)| Provides audio output and connection to a DVR, VCR, etc.
[13] Audio Terminal Block| A 3-pin terminal block marked A, B, C.
Accepts wiring from the remote Louroe Microphone.
A is 12Vdc Power
B is Audio
C is Ground

MANUFACTURED
IN THE

IMPORTANT NOTICE
When this equipment is used as part of an audio monitoring system, the law requires that the public be given notice of AUDIO MONITORING ON THE PREMISES. A decal notice is included with each microphone shipped.

Federal Law References:
Federal Regulations, US Code, Title 18. Crime and Criminal
Procedure, Sec 2510.

WARRANTY LOUROE ELECTRONICS® warrants that at the time of shipment products manufactured by LOUROE ELECTRONICS® to be free of defects in material and workmanship. Should a defect appear within one year (12 months) from date of shipment, LOUROE ELECTRONICS® will, at its sole discretion, repair or replace the defective equipment. This equipment shall not be accepted for repair or return without prior notification by LOUROE ELECTRONICS® . This warranty does not extend to any Louroe product that has been subjected to improper or incorrect installation, misuse, accident, or in violation of installation instructions provided by LOUROE ELECTRONICS® : Returned shipments to LOUROE ELECTRONICS® shall be at customer’s expense. LOUROE ELECTRONICS® will return the equipment prepaid via best way.

LOUROE ELECTRONICS® 6 9 5 5 VA L J E A N AVENUE, VAN NUYS, CA 91406 TEL 818-994-6498 FAX
website: www.louroe.com e-mail: sales@louroe.com
ms_1_inst_11/12

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals