SCA PLU 632324 Electric Motorised Jockey Wheel User Manual

SCA PLU 632324 Electric Motorised Jockey Wheel

WARNING: Always pay attention to the Electric Motorised Jockey Wheel. If the Electric Motorised Jockey Wheel abnormally warps / twists / bends, stop working immediately.

• Apply blocks to the wheels of the trailer, camper, boat, or caravan when on an incline.
• The height of the Electric Motorised Jockey Wheel can be manually adjusted for easy hitching to the tow vehicle, Only move with the jockey wheel in the lowered position.
• DO NOT push or pull your trailer, camper, boat, or caravan over 5° gradient.
• When you push or pull the vehicle on a gradient, make sure the Electric Motorised Jockey Wheel is in the lowered position.

SAFETY PRECAUTIONS

1. Please read this manual carefully before use. Keep the manual in a safe place for future reference.
2. Please observe the surrounding area when operating the Electric Motorised Jockey Wheel.
3. Please disassemble the Electric Motorised Jockey Wheel when not in use.
4. DO NOT exceed the rated capacities when using the Electric Motorised Jockey Wheel.
5. DO NOT use the Electric Motorised Jockey Wheel for long-distance movement as a motor will overheat.
6. DO NOT submerge the Electric Motorised Jockey Wheel in water.
7. Always disconnect the Electric Motorised Jockey Wheel power cable when not in use.
   Stop operating the Electric Motorised Jockey Wheel if the unit CANNOT find traction on a slippery surface.

PARTS DIAGRAM

The below image shows the parts that are included in the Electric Motorised Jockey Wheel

1. Motor & Gear System
2. Control Box
3. Mounting Bracket
4. Jockey Wheel Lift Handle
5. Handlebar
6. Control Handle

INSTALLATION OF THE ELECTRIC MOTORISED JOCKEY WHEEL

1. Step 1 : Connect the Upper Handlebar and the Lower Handlebar using the M8 Lock Bolt.
2. Step 2 : Attach the Assembled Handlebar to the main body using the M8 Lock Knob. Connect the Plug of the Handle Cable into the Control Box.
3. Step 3: Insert the Latch Pressure Plate into the Latch Fixed Plate, then attach the Latch Fixed Plate to the drawbar of vehicle by the using 2 x M12-120 Hex Bolts, 2 x M12 Flat Washers and 2 x M12 Nylon Lock Nuts.
4. Step 4: Lock the Latch Pressure Plate together with the Latch Fixed Plate by using the M12 Flat Washer and M12-40 Hex Bolt.
   • Ensure that the Rib is locked into the slot on both the Latch Fixed Plate and the Latch Pressure Plate before tightening.
   • Use the Correct Rib for the lowest operating height is selected when in use.
5. Step 5: Connect the Power Cable to the Power Socket on the Control Box. Connect the RED end to the Positive Terminal and connect the BLACK end to the Negative Terminal. Connect the 50 Amp Connector to the 12V DC Power Source.

TIPS FOR SAFE OPERATION

1. Electric Motorised Jockey Wheel is rated at 2,270kg Maximum Vehicle Load and 272kg Maximum Jockey Wheel Load. Overloads can damage the Electric Motorised Jockey

2. Wheel’s motor and Solid Rubber Wheel etc.
   Make sure all nuts and bolts etc are securely fastened before operating the Electric

3. Motorized Jockey Wheel.

4. Check if the Power Cable is connected correctly and all connections are tight.
   DO NOT use a Power Cable that is in poor condition, squashed, torn or any other visible damage.

5. This Electric Motorised Jockey Wheel is equipped with a 30A Auto Reset Circuit Breaker from overheating of the motor. Once the Circuit Breaker is activated, stop working for 5 minutes, and let the motor cool down before resuming to use of the Electric Motorised Jockey Wheel.

6. Avoid the use of the Electric Motorised Jockey Wheel in wet conditions (rain).

OPERATION GUIDE

• Take time to assess your situation and plan your movement.
• Mount the Electric Motorised Jockey Wheel to the drawbar of the vehicle.
• Locking pin and cover (not included) are recommended.
• Assemble the Handlebar, connect the Power Cable to the Power Socket on the Control
  Box and connect the 50 Amp Connector of the Power Cable to the 12V DC Power Source.
  Press the Button on the Control Handle to move the Electric Motorised Jockey Wheel in the desired direction you wish to move the Electric Motorised Jockey Wheel.

MAINTENANCE

All moving parts within the Electric Motorised Jockey Wheel have been lubricated using high-temperature lithium grease. No internal lubrication is required.

If the Electric Motorised Jockey Wheel is being used in high moisture conditions for long periods, internal lubrication will be necessary, please find a professional technician for maintenance.

TROUBLESHOOTING

•  Power Cable’s connection loose

•  Motor failure

•  Circuit breaker activated from overheating of the motor

| •  Press the ON/OFF power switch on the control box

•  Check all connections are tight

•  Replace motor

•  Stop working for 5 minutes, let the motor cool down

Slow motor speed| •  Low voltage on the motor or too much weight on a jockey wheel| •  Recharge battery

•  Check the weight on a jockey wheel

Loud noise emitted from the motor| • The jockey wheel is overloaded

• The jockey wheel is being used on a greater than 5°

| •  Decrease the weight on the jockey wheel

•  Cease using the jockey wheel if the incline is greater than 5°

SPECIFICATIONS

PLU: 632324 CODE: JW01
Manufactured and Packaged for SRGS PTY LTD ABN 23 113 230 050 6 Coulthards Avenue, Strathpine, Queensland 4500, Australia

MADE IN CHINA

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>