Portal FL-SP-305-BG, FL-SP-305-BL, FL-SP-305-OR, FL-SP-305-CAMO Inflatable Stand Up Peddle User Manual
- June 7, 2024
- Portal
Table of Contents
- CAMO Inflatable Stand Up Peddle
- ⚠️ WARNING
- Safety Check list
- GENERAL PADDING INFORMATION
- How to Use
- PORTAL ISUP PARTS LIST
- Part Ref.
- Description
- Quantity
- BOARD STRUCTURE
- iSUP Feature
- Part Ref.
- Description
- Quantity
- GETTING READY – INFLATING PORTAL ISUP
- INFLATION TIPS AND PRECAUTIONS
- 5.To Attach Stabilizing Fin
- BOARD K DETECTION AND REPAIR
- Small Repairs
- Large or Difficult Repairs
- BOARD CARE AND STORAG!
- BOARD FOLDING STEPS
- PORTAL STAND UP PADDLEBOARD REGISTRATION CARD
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
CAMO Inflatable Stand Up Peddle
Portal™
enter the adventure
Model
⚠️ WARNING
Paddle sports can be dangerous and physically demanding. Users of this product should understand that participating in stand up paddling can result in serious injury or death. Observe all applicable watercraft laws, and use common sense
Safety Check list
- Check your board and equipment before going in the water,
- Always paddle with others,
- Always wear a leash attaching you to the board
- Wear a Coast Guard approved personal flotation device.
- Always wear protective clothing
- Always paddle in safe conditions.
- Be aware of changing weather conditions
- Avoid paddling in off shore wind or windy conditions.
- Do not exceed your pedaling ability; be aware of your limitations.
- DO not use alcohol or mind altering drugs prior to or while using this product
GENERAL PADDING INFORMATION
How to Use
-
Assume A Comfortable Stance: both fee positioned roughly shoulder width apart. Knees slightly
bent in a relaxed upright pose, with shoulders back and looking ahead, -
Paddle Grip: Place one hand horizontally on top of the paddle handle, and place your other hand approximately 24” down the shaft Paddle in a comfortable forward mation, with arms slightly bent.
-
To Turn Left: concentrate padding onthe right hand side of the board
-
To Turn Right: concentrate paddling on the left hand side of the board
PORTAL ISUP PARTS LIST
Please Check All The Part Are Present In Your Package Before First Use
Part Ref.
|
Description
|
Quantity
---|---|---
A| Inflatable Stand-Up Paddle Board| 1
B| Detachable Fin| 1
C| Ankle Safety Leash| 1
D| Carry Backpack| 1
E| Paddle Fin| 1
F| Aluminum Paddle Body w/ Adjustable Clasp| 1
G| Adjustable Aluminium Paddle Grip| 1
H| Hand Pump w/ Gauge| 1
I| Repair Kit| 1
J| Phone waterproof bag| 1
K| Manual Pump Inflation Hose w/ High Pressure Adapter| 1
BOARD STRUCTURE
iSUP Feature
Part Ref.
|
Description
|
Quantity
---|---|---
I| 1 Heavy-Duty Front Handle| 3
II| W Bungee Cord D-Rings| 6
III| ut Bungee Storage Cord| 1
IV| Vv Non-Slip EVA Foam Deck Board| 1
V| v High Pressure Inflation Valve| 1
VI| vl ‘Ankle Safety Leash D-Ring| 1
VII| vil Fixed Stabilizing Fins| 2
VIII| vill Removable Stabilising Fin| 1
GETTING READY – INFLATING PORTAL ISUP
1.Unpack Your iSUP Set
Choose a smooth and clean surface to unfold board. Roll out the ISUP board
completely flat
with Portal logo side facing up.
2.Unlock Valve for Inflation
Find the high pressure inflation valve near the bottom of the board. Twist the
cap counter clockwise
to detach and access the center valve pin. Press the center pin once to pop it
up slightly. Now the
valve is in “open” position for air inflow. Be careful of any sand or debris
around the valve area when
inflating and deflating, as small particles could become airborne with the
release of air.
Always keep the center pin in “close” position and screw the cap clockwise to
block air outflow when
in use. This will prevent accidental air release and entrance of any particles
into the air chambers.
3.Pose
Connect the end with the pressure adapter to the pump’s “inflation” nozzle
around the neck,
twist counter clockwise to secure.
4.to secure air pressure
When PSI monitor reaches a desired level, please detach the hose from the
valve. Press the
center valve pin down to “close” position and screw the cap clockwise to
secure are pressure.
INFLATION TIPS AND PRECAUTIONS
-
The board can be inflated either with our hand pump or an electric pump. The electric pump
can inflate the board to a moderate pressure and save a lot of time with about 90% of the
required air volume. You will need to use your hand pump to inflate the chambers to the
correct pressure. -
Do not use an air compressor. Damage to your board caused by over inflation from an air compressor is not covered by your warranty.
-
After 2 or 3 days there may be a small decrease of pressure due to temperature change. If so, add a few pumps of air.
-
Before undertaking a long paddle, inflate the board for a full 24 hours to be sure the board is airtight. If you are seeing a consistent decrease in air pressure, follow the instructions for leak detection in the board repair section of this manual.
5.To Attach Stabilizing Fin
The two side fins are fixed to the board and no need to operate. Once the
board is inflated, flip
over the board facing down to attach the stabilizing fin, Slide in the center
fin vertically to the
end of the fin base, then insert the fixed pin horizontally to lock the fin in
place.
6.Assemble Aluminum Telescopic Paddle
To assemble the paddle, connect the middle bar and fin part first. Hold the
button part and slide
in the middle bar until hearing a click. Then slide in the handle part and
adjust the height
appropriately.
For an ideal height, adjust until the length is comfortable for both hands to
coordinate. A longer
paddle is better suited for a smooth, less frequent paddle motion. A shorter
paddle is good for
performance and competition riding.
7.Ankle Safety Leash Use
Then attach the other end of the safety leash to the safety D-ring by pulling
the inner rope
through the ring and secure in place with the Velcro tape.
8.To Deflate Without A Manual Pump
When packing your iSUP, remove all detachable parts. Then lay the board facing
up on a smooth
surface. Clean any unwanted debris and, especially around the valve area. Open
the valve cap
and press the center pin to start releasing air. There will be an initial
burst of air, but will turn to
slow release. When the air outflow slows down, start rolling up the board from
the opposite end
and fold it into a packing size. When packing, lock the valve cap to protect
the center pin and
elongate iSUP lifetime.
9.To Deflate With A Manual Pump
Remember to step on the pump securely, to prevent slipping.
BOARD K DETECTION AND REPAIR
About PVC
Your new stand up paddleboard is made from a durable PVC. If a tear or
puncture does occur,
PVC is very easy to repair. Repairs are easily done with your included patch
kit.
Read the following paragraphs for leak detection and repair tips.
Air Leak Detection
If the board is losing air pressure not caused by colder temperature, then
check for leaks. Start
with the valve.
A leaking valve is rare, but if you did find one, please contacts us via
fiservice@topsunholdings.com. Your paddleboard comes with 1 year quality
warranty.
If you continue to have problems it’s probably time to order a replacement
valve kit or anew
model. Replacement of the whole valve can be done with a simple tool that
comes with the
replacement valve kit.
Small Repairs
Punctures less than 1/8” in size can be repaired simply without a patch.
Deflate your board,
then clean and dry the area to be repaired. Apply a small drop of glue to
cover the puncture,
and let it dry 12 hours.
If your board needs repair, use the patches in the repair kit and follow these steps:
- Deflate the board completely, lay it flat and wait for it to dry.
- Cut a patch that is 2 inches larger than the tear/rip all the way around.
- Use alcohol to clean the repair area.
- Apply three coats of adhesive to the patch and the board. Wait 5 minutes in between each coat.
- Place the patch over the tear/rip. The adhesive will react quickly, so make sure the positioning is precise/accurate. Use the roller to ensure the patch lays flat and even.
- Wait 24 hours before re-inflating the board.
Large or Difficult Repairs
If you have a difficult repair, please send us email and we will advise you on
the best way to
repair it.
BOARD CARE AND STORAG!
To ensure your iSUP would stay in the game longer,
- Before storing, hose off the board and let it dry completely to prevent mildew buildup.
- Do not use harsh chemicals for cleaning. Most dirt can be removed with a mild soap and fresh water.
- You may store the board inflated or deflated. If you deflate the board, we recommend that you store it in the protective bag that came with the board.
- If storing the board outdoors, raise it up off the ground and cover it with a tarp to prevent exposure to the elements.
- Hanging the board is not recommended.
- Do not store in extreme conditions (i.e. above 150F or below -10F)
- Store in a clean, dry place.
BOARD FOLDING STEPS
The board storage bag is designed to allow you to get your board into the bag
as easily as
possible with minimal folds. Do not roll up the board too tight when storing
it while deflated.
Follow the diagram below for the best folding procedures.
STEP 1
STEP 2
STEP 3
PORTAL STAND UP PADDLEBOARD REGISTRATION CARD
To register your online purchase, please send a screenshot of your order
details to our after
sales team: flservice@topsunholdings.com.
To thank you…..in addition to activate the 180-day extended quality warranty.
Information are collected for warranty service and product R&D only.
Thank you for shopping with LC Leisure ~ Licensed Amazon Shop for Portal
Outdoor.
fiservice@topsunholdings.com
@portaloutdoor official
@portaloutdoor_official
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>