SCA PLU 585722 5 Inch Dynamic Guideline Reverse Camera Kit Instruction Manual
- June 9, 2024
- SCA
Table of Contents
SCA PLU 585722 5 Inch Dynamic Guideline Reverse Camera Kit
WARNING
To avoid personal injury and/or property damage, please read and follow ALL of
these instructions before assembling and operating.
Product overview
Thank you for purchasing the SCA-RC2 Dynamic guideline reversing camera. The
Dynamic guidelines show the path of intended motion of the vehicle while
reversing.
This product is designed for easy DIY installation but does require some
specific tools.
Package components
- Monitor (Labelled 1)
- Reverse camera signal harness (Labelled 2)
- Monitor power harness (Labelled 3)
- Video extension cable (Labelled 4)
- Camera power harness (Labelled 5)
- Reverse camera (Labelled 6)
- Adhesive mount
- Suction mount
Wiring Install Diagram
The video signal is transferred from the camera to a monitor/display via an RCA cable that will need to be run through the boot, through the passenger compartment to the monitor/display wired loom, run under the dash. From there the power and video signals are sent directly to the monitor/display. At the rear of the car the camera is powered directly from the reversing tail lamp. Check the priority input on the monitor/display.
Wiring Diagram
Installation
When mounting the camera, make sure that the camera does not cover any part of the license plate. Choose a position that does not impede the access/operation of the boot release or tailgate latch.
STEP 1. Mounting the Monitor
- Check the mounting position of the Monitor and camera first before installation.
- Ensure windscreen or dash is clean and free of debris. Use an alcohol wipe to enhance adhesion.
- Remove backing off 3M tape off mount and press & hold firmly to the surface for 60 seconds.
- Fix where the drivers vision is not blocked. Do not install the device on airbag or within its working range.
STEP 2. Connect Monitor Input Harness
Connect signal output cable of the monitor to the RCA input cable.
STEP 3. Connect Monitor Power Harness
Recommended Power Connection: The end of the monitor power harness cable
connects to the red power input cable connector. This connection splits into
two wires, a red and a black wire. Connect the red wire (+12V) to a wire that
is powered when the vehicles accessories or ignition is turned on. Connect the
black wire, using a suitable ring terminal to vehicle chassis.
Alternative Power Connection: The monitor can also be powered from the reverse
light in the vehicle. Connect the red wire (+12V) from the red power input
cable connector to the red wire on the RCA video lead at the display monitor
end of the cable. At the camera end of the cable, connect the red wire to
positive (+12V) at the reverse light in the vehicle. Connect the black wire
from the monitor harness, using a suitable ring terminal to vehicle chassis.
NOTE: if you power the monitor with this method, the start up screen on
the display will appear everytime you select reverse, which will delay the
reverse image from appearing.
STEP 4. Connect Video Extension
Cable Connect one end of the video extension RCA cable to the RCA socket from
the camera power harness, then run the RCA cable to the front under side of
the driver side dash board to connect to Monitors video input RCA (Yellow
AV1).
NOTE: There may be multiple video inputs for different monitors. (ie AV1
or AV2). When using both inputs, when triggerred AV1 becomes priority. To do
this you may need to remove the rear seat and or floor scuff panels to run the
extension cable along the side of the vehicle. The RCA cable will be hidden
when you replace the scuff panels.
STEP 5. Connect Camera Power Harness
Connect the RED wire of the camera power harness to the wire that supplies
power to the reversing lamp (the wire that is powered only when the car is put
into reverse). Before making the electrical connection, temporarily disconnect
the camera harness from the power plug whilst making the connection to the
reversing lamp. Use a suitable splicing/crimp connector (scotch lock type) or
strip connector. This connection can also be soldered, making sure to insulate
the joint with electrical insulation when done. The camera power harness has
two wires to connect (positive (+) to reverse lamp and (-) to chassis.
STEP 6. Connect Camera Harness
Connect the camera power harness to the camera harness. Mount the camera to
vehicle
NOTES: CAN BUS
In the event that the cars reversing lights are driven by CAN BUS the above
wiring system may not trigger the system correctly. It may even create a globe
fault warning. In this case a CAN BUS module (sold separately) may need to be
installed. However, just because the vehicle has a CAN BUS system does not
necessarily mean that it will require such a module to work. In fact the
opposite is true. Most vehicles do not require an additional module. If a CAN
BUS module is required we recommend seeking advice from a professional
installer.
Some cars that switch negative, run LED or digital data controlled lighting
systems may not deliver correct voltage to run the camera, or could cause
flicker with the image. If the voltage at the reversing wire light is less
than 12 volts it may be necessary to use a relay to supply power to the camera
harness from the wiring in the front of the car. In this case the reversing
light only needs to trigger the relay. Use a multimeter to test this.
Testing the reversing camera action
- Engage the park brake and turn the ignition key to the on position. DO NOT start the vehicle.
- Select reverse gear with the gear shift. The monitor/display will trigger and turn on automatically when it is energized from the reverse light.
MENU FUNCTIONS
Function buttons located on the back of monitor
- Press continuously the Menu button to scroll through settings
- Press the + or – button to increase & decrease the settings
- The menu settings on the monitor will save and dissapear from the display after 3 seconds
- Brightness: Adjusts screen brightness (50 – 100)
- Contrast: Adjusts screen contrast (50 – 100)
- Saturation: Adjusts screen saturation (50 – 100)
- Language: Select menu language
- Mode: Changes display between 16:9 & 4:3 ratio
- Reset: Resets all settings back to factory default
Product specifications
Display | 5.0 inch 16:9 TFT-LCD |
---|---|
Lens view angle | 100 degree wide viewing angle |
Resolution | 420 (TV Lines) |
Effective pixels | 480(H)*234(V) |
TV system | PAL/NTSC |
Contrast | 500:1 |
Brightness | 500cd/m2 |
Monitor Rated working voltage | 12V DC |
Video inputs | 2 |
Camera | Dynamic guidelines |
Dimensions | W125 x H82 x D30 mm |
WARRANTY
This product is guaranteed against defects for a period of 12 months from date
of purchase. This warranty is provided by SRGS Pty Ltd ABN: 23 113 230 050
(Supercheap Auto) of 6 Coulthards Avenue, Strathpine, Queensland 4500,
Australia. Ph (07) 3482 7500. Supercheap Auto will offer a repair, replacement
product or store credit if the product is assessed as being defective during
the warranty period. To claim under this warranty, take this product to the
Front Service Desk of your nearest Supercheap Auto store. For store locations,
visit www.supercheapauto.com.au (AUS) or
www.supercheapauto.co.nz (NZ). You will
need your receipt or proof of purchase. Additional information may be
requested of you to process your claim. Should you not be able to provide
proof of purchase with a receipt or a bank statement, identification showing
your name, address and signature may be required to process your claim. This
product may need to be sent to the manufacturer to assess the defect before
determining any claim. Faults or defects caused by product modification,
misuse and abuse, normal wear and tear or failure to follow user instructions
are not covered under this warranty. Our goods come with guarantees that
cannot be excluded under the Australian Consumer Law. You are entitled to a
replacement or refund for a major failure and for compensation for any other
reasonably foreseeable loss or damage. You are also entitled to have the goods
repaired or replaced if the goods fail to be of acceptable quality and the
failure does not amount to a major failure. Any expenses incurred relating to
the return of this product to store will normally have to be paid by you. For
more information contact your nearest Supercheap Auto store. The benefits to
the consumer given by this warranty are in addition to other rights and
remedies of the Australian Consumer Law in relation to the goods and services
to which this warranty relates.
Manufactured and packaged for SRGS Pty Ltd ABN: 23 113 230 050 6 Coulthards Avenue, Strathpine, Queensland 4500, Australia
References
- Supercheap Auto New Zealand | Buy Auto Spares and Parts Online
- Supercheap Auto Australia | Online Auto & Car Parts Store
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>