Panasonic F-MU408-WT Electric Fan Owner’s Manual

Operating Instructions
Electric Fan (Wall Fan)
Model No.
F-MU308, F-MU408

SPECIFICATION

Before operating this set, please read these instructions completely.
Use only with rated voltage.
If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard.
This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction conceming use of the appliance by a person responsible for their safety. Children should be supervised to ensure that they do not play with the appliance.
To avoid the possibility of causing injury to users or damage properties, please follow all the explanation written below. The manufacturer is not responsible for accidents and injuries caused by defective or deficient installation.

SAFETY PRECAUTIONS

BE SURE TO READ AND FOLLOW THESE SAFETY DIRECTIONS

Please read and follow these safety precautions carefully in order to avoid possible injury to yourself or others and damage to your belongings.

• The following symbols indicate the degree of possible danger if the relevant precautions are ignored.
  WARNING This sign wam of death or seriuos injury.
  CAUTION This sign wam of damage to property.

• Precautions are classified using the following symbols.
  This symbol denotes a PROHIBITED action.
  This symbol denotes actions that are COMPULSORY.

• Never try to take apart, repair or modify this product.
  Do not take apart
  It may cause fire or electric shock.

  • Contact the dealer for repairing this product.

• Do not plug line cord into outlet until fan has been completely assembled.

• Do not connect this unit to power supply other than destinated country-rated voltage.
  Prohibited
  Otherwise, it may cause fire and injury.

• Do not contact with water.
  Avoid water

• Do not damage power cord or main plug.

• eg: modify, put near heat generating appliance, abnormally twist or bend, forcefully elongate, pull heavy weight, bundle up power cord.
  Prohibited
  Causing injury, electric shock or even fire due to short circuit.
  If the supply cord is damaged, it must be replaced by the manufacturer or its service agent or a similarly qualified person in order to avoid a hazard.

• Make sure plug is fully inserted into socket.
  Loose engagement of plug and socket may cause electric

  • Do not use damaged plug or loosen socket.

• The safety screw must be always connected.
  Can cause injury if drops.

• Wipe off dust on the plug and socket periodically.
  Accumulation of dust on plug-in humid season may cause poor insulation and may result in fire.

  • Disconnect from power supply and use a piece of dry cloth to clean the plug.
  • Unplug the fan if it will not be used for a long period.

• Disconnect power supply before cleaning.
  Unplug
  Otherwise, it may cause electric shock.

• Never touch the plug if your hands are wet.
  No wet hand
  May cause electric shock.

• Follow strictly to all the instructions given.
  Installation error can cause fire, electric shock, set to fall and injuries.

  • Installation must be done by a competent personnel.

CAUTION

• Do not use under the following situations :

  • Near to gaseous fuel cooker
  • Place full of inflammable gas
  • Place expose to rain or water pour
  • Near insecticide
  • Oil corrosive solvent
  • High temperature
  • High humidity
  • Near chemicals, oil, dust area.
    Prohibited
    May cause bad effect in quality and Dilarang dangerous condition.

• Don’t place the fan on unstable surface or near obstacles.
  Prohibited
  Risk on injury by falling fan.

• Avoid continuously exposure of direct wind from the fan.
  Prohibited
  It may cause discomfort.

• Do not put your fingers into the guard or any moving part of the fan.
  Prohibited
  Causing injury.

• Hold the plug when disconnect from main supply, never pull the cord.
  May cause short circuit and damage of power supply cord and leading to fire or electric shock.

• Make sure all screws and connection are tightly screwed and secured.
  Can cause injury if drops.

• Please install the safety screw before fixing the guard.

• The fan is recommended to be installed so that the blades are more than 2.5 m above the floor (for fans intended to be mounted at high level).

PARTS IDENTIFICATION

1. FRONT GUARD
2. GUARD RING
3. SPINNER
4. BLADE| 5. GUARD SET NUT
6. REAR GUARD
7. MOTOR
8. STAND
---|---

ACCESSORIES

INSTALLATION

1. install the wall bracket to the wall

install the fan stand

Securely install the wall bracket onto a vertical wall using the accessory wood screws.

• For the installation of the wall bracket, choose a wall which is thicker than half an inch or a part of the wall covering a pillar or a crosspiece.
  For wooden wall no need to use wall plug.

Firmly install the fan stand vertically onto the wall bracket. At this time, moving the fan stand sideways slightly may make installation easier and ensuring it is fully hooked onto wall bracket.

• Do not put a power cord between the wall and the fan.
• Check that the fan stand has been securely installed.

1. The wall bracket and safety screw should be able to withstand a load of 392N/40kg when properly fixed to the wall
2. This figure is shown generic method for installation on concrete or brick wall. Variation on wall quality and plug (pipe) quality would affect secure of installation. Please consult with qualified person(s) if there is difficulty on installation.

SAFETY SCREW INSTALLATION GUIDE

1. Fix the fan stand as shown in illustration 1)
2. Cross marking for the purpose of drilling safety screw hole as shown in illustration 2).
3. Unhook the fan stand from the wall bracket as shown in illustration 3).
4. For easy to make a hole, drill a hole according to the template paper provided.
5. Install the fan stand as shown in illustration 4).
6. Safety screw should tighten until stopper only as shown in illustration 5).

ASSEMBLY METHOD

1. After fixed set properly, power cord position must be as illustration side. Pull out the tube from shaft and wipe off excess grease.

2. Turn the guard set nut (A) counterclockwise and remove it.

3. Place the rear guard in the proper position. Fit the projections

4. Turn the guard set nut (A) clockwise and tighten it completely.
   Attach the blade with ensure blade projection and shaft pin at same position. Then, turn the spinner securely to the counter clock wise. If it is not tightened completely, an abnormal sound will be heard when the blade stops. Please be sure to tighten it completely.

5. Align the guard ring’s hook with the alignment mark of the rear guard. Press the front guard so that the guard ring fits to the rear guard all around.

6. Snap together the front and rear guards.

OPERATION

|
---|---

• To turn on the fan, pull the speed control pull cord.
  To turn it off, pull the cord so that the indicator points to “O”.

• When automatic oscillation is desired, pull the oscillation cord.
  The oscillation will stop when the cord is pulled again.

• The air direction can be adjusted upward or downward by simply moving the guard up or down as shown in the figure. Adjust the angle of the fan only after first confirming that it has stopped rotating.

• If the fan did not stop at the desired angle, use a screwdriver to tighten the bolt.

• To change the direction of the airflow, push the edge of the guard to the desired position.

Panasonic Manufacturing Malaysia Berhad. (6100-«
No. 3, Jalan Sesiku 15/2, Section 15, Shah Alam Industrial Site,
40200 Shah Alam, Selangor Darul Ehsan, Malaysia.
Made in Malaysia.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>