fri-jado 20230926 Combi Changing Oven Door Instruction Manual
- June 17, 2024
- fri-jado
Table of Contents
Fri-jado 20230926 Combi Changing Oven Door
Product Information
Specifications
- Revision: 08/2023
- Software Version: 0.7.1
- General Information
- The GO Combi is an oven that requires proper installation and servicing by qualified service technicians.
- This user manual provides instructions on how to mount the stand for the oven.
Target Group
- This document is intended for service technicians who have received training in installing and servicing the GO Combi oven.
- Only qualified service technicians should install and service the oven.
Technical Changes
- Please note that this document is subject to changes without notice. Stay updated with the latest revisions and software versions.
More Documentation
- For additional information about the GO Combi oven, please refer to the documentation available on our website.
Warranty
- For warranty information, please visit our website for further details.
Permissions
- To access certain functions such as changing the oven setup, using test functions, and updating software, log in as Technician (576021) to gain the necessary rights.
Safety Information
- Before using, installing, or servicing the product, it is essential to read this document. Ensure that the installation and operation comply with local regulations and accepted codes of good practice.
- Read and familiarize yourself with the safety instructions provided in the user manual, installation manual, and service manual before performing any work on the oven.
- All maintenance and repair tasks should only be carried out by qualified installation and service technicians. Failure to do so may result in operator injury and/or damage to the oven.
Product Usage Instructions
Before Replacement:
- Before replacing any parts or making any modifications to the equipment, ensure that the oven is turned off and disconnected from the power source.
Tools
For mounting the stand, you will need the following tools:
- Tool 1
- Tool 2
- Tool 3
Spare Parts
Ensure that you have all the necessary spare parts required for mounting the stand.
Estimated Working Time
The estimated time required to complete the mounting process is approximately 30 minutes.
Stand Overview
The GO Combi oven can be mounted on two different stand models:
- Basic Stand
- Stand for Table and Stackit
Assembling the Frame
Follow these steps to assemble the frame of the stand:
- Step 1: Instructions for assembling the frame.
- Step 2: Additional instructions for assembling the frame.
- Step 3: Further instructions for assembling the frame.
Mounting the Legs on a Standard Stand
To mount the legs on a standard stand, please follow these steps:
- Step 1: Instructions for mounting the legs on a standard stand.
- Step 2: Additional instructions for mounting the legs on a standard stand.
- Step 3: Further instructions for mounting the legs on a standard stand.
Mounting the Legs on a Stackit and Table Stand
If you are using a Stackit and table stand, the process of mounting the legs may differ.
Please follow these steps:
- Step 1: Instructions for mounting the legs on a Stackit and table stand.
- Step 2: Additional instructions for mounting the legs on a Stackit and table stand.
- Step 3: Further instructions for mounting the legs on a Stackit and table stand.
Mounting the Supports
Follow these steps to mount the supports:
- Step 1: Instructions for mounting the supports.
- Step 2: Additional instructions for mounting the supports.
- Step 3: Further instructions for mounting the supports.
Mounting the Oven on a Stand:
To mount the oven on a stand, please follow these steps:
- Step 1: Instructions for mounting the oven on a stand.
- Step 2: Additional instructions for mounting the oven on a stand.
- Step 3: Further instructions for mounting the oven on a stand.
Mounting an Oven with Fat Separation on a Stand
If you have an oven with a fat separation feature, the mounting process may vary.
Please follow these steps:
- Step 1: Instructions for mounting an oven with fat separation on a stand.
- Step 2: Additional instructions for mounting an oven with fat separation on a stand.
- Step 3: Further instructions for mounting an oven with fat separation on a stand.
Mounting HydroShield Water Filter on the Stand
If you are using a HydroShield water filter, follow these steps to mount it on the stand:
- Step 1: Instructions for mounting the HydroShield water filter on the stand.
- Step 2: Additional instructions for mounting the HydroShield water filter on the stand.
- Step 3: Further instructions for mounting the HydroShield water filter on the stand.
Different Stand Models:
- The GO Combi oven is compatible with various stand models.
- For more information, refer to the documentation specific to each stand model.
Frequently Asked Questions (FAQ):
Q: Who should install and service the GO Combi oven?
- A: The oven must only be installed and serviced by qualified service technicians.
Q: Where can I find more documentation about the oven?
- A: You can find more documentation about the oven on our website.
Q: Are there any technical changes to this document?
- A: This document is subject to changes without notice. Stay updated with the latest revisions and software versions.
Q: Can I perform maintenance and repair tasks on the oven myself?
- A: No, all maintenance and repair tasks must be carried out by qualified installation and service technicians to ensure safety and prevent damage to the oven.
Q: How long does it take to mount the stand?
- A: The estimated time required to complete the mounting process is approximately 30 minutes.
General information
Target group
- This document is aimed at service technicians who have been trained in installing and servicing the oven. The oven must only be installed and serviced by qualified service technicians.
Technical changes
- This document is subject to changes without notice.
More documentation
- You find more documentation about the oven on our website.
Warranty
- You find more information about the warranty on our website.
Permissions
- Log in as “Technician” (576021) to have the necessary rights to be able to change the oven setup, use the test functions, update software, etc.
Safety information
- Read this document before using, installing, or servicing the product. Installation and operation must comply with local regulations and accepted codes of good practice.
- Read the safety instructions in the user manual, installation manual, and service manual before you perform any work on the oven.
- All maintenance and repair must be carried out by qualified installation and service technicians only.
- Installation and/or service by others than qualified service technicians may result in injury to the operator and/or damage to the oven.
Before replacement
- Make sure the required tools are available.
- Unpack the spare parts and check if all parts are available
- Make sure the working area is tidied up, clean, and safe to prevent personal injury and damage to the equipment.
Tools
- Slotted screwdriver
- 8 mm socket screwdriver
- 8 mm wrench
Spare parts
- The stand comes in many variations. The spare part number depends on the stand and accessories that you have ordered.
- 107954, Basic stand 1/1GN, including standard feet, with fat separation
- 107955, Basic stand 1/1GN, including standard feet without fat separation
- 107957, Basic stand 2/1GN, including standard feet with fat separation
- 107956, Basic stand 2/1GN, including standard feet without fat separation
- 107977, Stand for table and Stackit 1/1GN including standard feet with fat separation
- 106171, Stand for table and Stackit 1/1GN including standard feet without fat separation
- 107978, Stand for table and Stackit 2/1GN including standard feet with fat separation
- 106172, Stand for table and Stackit 2/1GN including standard feet without fat separation
- 107970, Floor mount
- 107971, Castors
- 107972, Racks 1/1GN
- 107973, Exterior cabinet doors 1/1GN-EN
- 107974, Exterior cabinet doors 2/1GN
- 107975, Bracket for filter
- 107976, Racks 2/1GN
- 110176, Rack support locking system
Estimated working time
- Approximately 30 minutes.
Stand overview
Mounting the stand
Assembling the frame
- Place the two parts of the frame on a flat surface with the bottom pointing upwards.
- Push the two parts of the frame together
- Fasten the two M5x10 screws on each side using a slotted screwdriver.
Mounting the legs on a standard stand
- Place the frame on a flat surface with the bottom pointing upwards.
- Place the leg in the corner of the frame and fasten it with four M5x10 screws.
- Mount the other three legs in the same way.
Mounting the legs on a Stacking kit and table stand
- Place the frame on a flat surface with the bottom pointing upwards.
- Place the leg in the corner of the frame and fasten it with four M5x10 screws.
- Mount the other three legs in the same way
Mounting the supports
- Place the frame with the legs pointing upwards
- Fasten the two supports (A) on the right-hand and left-hand side with the FRH M5x12 screws using a flexible socket screwdriver.
- Fasten the two supports (B) in the front and back in the same way as above.
Mounting the oven on a stand
- In case of a Stacking kit solution, always mount the bottom oven on the stand before mounting the upper oven on the bottom oven.
- Detach the hose for the drip tray.
- If the oven is a table model, remove the four legs from the oven.
- Place the oven on the stand.
- Fasten the oven to the stand using 4 x hex screws and 4 x washers.
- The illustration below shows how to mount the oven on a standard stand.
- The procedure is the same for mounting a stand on a table or Stacking model.
- Fasten the two M5x10 screws on both the right-hand and left-hand sides of the oven.
- Attach the hose for the drip tray.
Mounting an oven with fat separation on a stand
In case of a Stacking kit solution, always mount the bottom oven on the stand before mounting the upper oven on the bottom oven.
- Follow steps 1-3 in the section “Mounting the oven on a stand”.
- Fasten the oven to the stand using 4 x hex screws and 4 x washers as well as 2 x M5x10 screws.
- Follow steps 5 and 6 in the section “Mounting the oven on a stand”.
Mounting water filter on the stand
Not roll-in and Stacking kit.
- The water filter can be mounted on the oven stands for the following oven types:
- Fri-Jado GO 6-1/1 GN
- Fri-Jado GO 10-1/1 GN
- Fri-Jado GO 6-2/1 GN
- Fri-Jado GO 10-2/1 GN
- On all other oven types and sizes, the water filter must be placed on the floor next to the oven.
- Fasten the bracket with 5 mm screws.
- Remove the two M5 screws.
- Remove the side plate.
- Fasten the brack beneath the oven. Use two M5 screws.
- Slide the filter head into the bracket.
- Mount the filter on the filter head by turning the filter counterclockwise into the filter head.
- Connect the hoses according to the section “Connecting the oven to a Water filter” in the installation manual.
Different stand models
- You can buy different accessories for the basic stand.
- The table below shows the different possibilities as well as which pre-drilled Holes to use when mounting the racks.
- Fri-Jado B.V.
- Blauwhekken 2
- 4751 XD Oud Gastel
- North Brabant
- The Netherlands
- T: +31 (0)76 508 5400
- M: info@frijado.com
- Fri-Jado France LLC
- 31 Parc du Golf – CS 90519
- 350 Avenue JRGG de la Lauzière
- 13593 Aix-en-Provence Cedex 3
France
- T: +33 (0)44 216 3560
- M: fr.info@frijado.com
- Fri-Jado UK Ltd.
- Ashley House
- Ashley Road UB8 2GA
- Uxbridge Middlesex
United Kingdom
- T: +44 (0)189 527 2227
- M: uk.info@frijado.com
- Fri-Jado Inc.
- 1401 Davey Road
- Suite 100 Woodridge
- IL 60517
USA
- T: +1 (0)877 374 5236
- M: us.info@frijado.com
Documents / Resources
| fri-
jado 20230926 Combi Changing Oven
Door
[pdf] Instruction Manual
20230926, 20230926 Combi Changing Oven Door, Combi Changing Oven Door,
Changing Oven Door, Oven Door, Door
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>