CATERPILLAR 924H Wheel Loader User Manual

: June 17, 2024
: CATERPILLAR

CATERPILLAR 924H Wheel Loader

Product Information

Specifications

Kit Part Number : 700535
Manufacturer : Caterpillar
Type : Wheel Loader
Model : 924H / 938H
Cabin Pressure : Max Set Auto Cabin Pressure

Product Usage Instructions

Installation Overview
The Caterpillar Wheel Loader 924H/938H requires the following installations

HEPA H14 Variable Speed Pressurizer
INPRESS TS Cabin Display with Data Recorder
HEPA Return Air Filter

Installation Steps

Ensure qualified staff wear the correct personal protective equipment when cleaning and servicing the unit.
Ensure the electrical power system is supplied by either 12V DC or 24V DC. No work should be carried out on the pressurizer system without following the correct safe work procedures and electrical safety measures.
Ensure all safety guards are in place while the air filtration system is running.

Safety Instructions
It is important to follow these safety instructions

HEPA filters cannot be cleaned and must be replaced at the end of their lifecycle or if the filter media has been damaged.
Ensure proper personal protective equipment (PPE) is worn when installing the system, including hard hats, eye protection, dust masks, ear protection, and protective clothing.

Maintenance Schedule
Follow the suggested maintenance schedule below. Please note that site conditions may alter this schedule

Inspect the Turbo Pre-cleaner every 500 hours.
Ensure the pressurizer blower is operational.
Inspect the HEPA Primary Filter (p/n: 500000) and replace when it is 80% or greater. Vacuum out the housing before replacing the filter elements.
Vacuum inside the cabin floor before replacing the HEPA Return Air Filter (P/N: 500026).
Check door seals, bolts, screws, mounts, filter canister, latches, and fixtures and fittings. Replace or re-tension if required.
Perform a 500-hour inspection after 15,000 hours or 36 months.

FAQ

Q: Can the HEPA filters be cleaned?
A: No, HEPA filters cannot be cleaned and must be replaced at the end of their lifecycle or if the filter media has been damaged.
Q: What personal protective equipment (PPE) should be worn during installation?
A: It is recommended to wear a hard hat, eye protection, dust mask, ear protection, and protective clothing during installation.

Kit Part Number : 700535
Parts and Service Manual
HEPA H14 Variable Speed Pressurizer | INPRESS TS Cabin Display with CO2 Sensor | HEPA Return Air Filter

+61 7 3276 7833
www.breathe-safe.com.au
sales@breathe-safe.com
62 Mica Street, Carole Park, 4300, QLD
Controlled Document : M0056
Issue Date : 01/08/23
Revision : 1

INSTALLATION

INSTALLATION OVERVIEW

SAFETY

WARNING

THE PRESSURISATION SYSTEM DESCRIBED IN THIS MANUAL HAS THE FOLLOWING AREAS WHICH MAY BE DANGEROUS IF NOT TREATED WITH GREAT CARE.
QUALIFIED STAFF MUST WEAR THE CORRECT PERSONAL PROTECTIVE EQUIPMENT WHEN CLEANING AND SERVICING THIS UNIT DUE TO DUST AND FIBRES WHICH MAY BE CAUGHT BY THE STAGES OF AIR FILTRATION DURING NORMAL UNIT OPERATION.
THE ELECTRICAL POWER SYSTEM IS SUPPLIED BY 12V DC OR 24V DC AND NO WORK SHOULD BE CARRIED OUT ON THE PRESSURISER SYSTEM WITHOUT THE CORRECT SAFE WORK PROCEDURES AND ELECTRICAL SAFETY MEASURES BEING TAKEN, AND ALL RELEVANT CIRCUIT BREAKER OPENED TO ISOLATE THE CIRCUIT.
THE AIR FILTRATION SYSTEM MAY HAVE SEVERAL TYPES OF HIGH-SPEED ROTATING EQUIPMENT INSTALLED WITH VERY SHARP EDGES. ENSURE ALL SAFETY GUARD ARE IN PLACE WHILE THE SYSTEM IS RUNNING.
Please be aware that HEPA filters cannot be cleaned and must be replaced at the end of their lifecycle or if filter media has been damaged.

Particulate Behaviour
This is the length of time it takes for a particle to drop from a height of 1.5m in STILL air.

Warehouses and workshops do not have still air, so hazardous airborne particulates may remain in air for longer, increasing chance for workers to breathe in dust. Ensure PPE is worn when installing this system.

CRITICAL PARTS & MAINTENANCE SCHEDULE

Maintenance Schedule
The following tables show our suggested maintenance schedule for all units. Please note that site conditions may alter this. Excludes high corrosion environments.
Data download is required to claim the 3-year warranty on Brushless Blower Motor.

**Inspect every 500 Hours and replace when filter is full***

Component / System	Action Required
Turbo Pre-cleaner	Check operation of the Turbo Pre- Cleaner.
Pressurizer Blower	Ensure blower is operational.
HEPA Primary Filter p/n: 500000	Inspect filter capacity indicator.

Replace HEPA filter when 80% or greater. Vacuum out housing before replacing the filter elements.
HEPA Return Air Filter P/N : 500026| Vacuum inside cabin floor before replacing filter.
Filter Frame Assembly, Mounts, Seals and Filter Housing|

Check door seals, all bolts, screws, and all mounts are secure.
Check the filter canister & ensure it is correctly fitted.
Check latches are operational and in good order.
Replace / Re-tension fixtures and fittings required.

15,000 Hours / 36 months*

Component / System	Action Required
500 Hour Inspection	All 500-hour inspection actions.
Pressurizer’s Blower 200002	Replace BRUSHLESS Pressurizer blower.

Critical Parts

fan capacity)

2| 500026| 1| HEPA Return Air Filter| 500* Hours
3| 200002| 1| Brushless Blower Motor – 24V| 15,000 Hours
4| 200027| 1|

Breath Safe Digital Display – Data
Recorder (INPRESS TS)

|

Filter service hours are subject to cab sealing efficiency, site conditions and correct system use.

**Suggested Schedule Servicing***

OPERATOR GUIDE

OPERATORS CHECKLIST

PRE-START
1.| Visually inspect the Breath Safe system for any damage.
2.| Visually inspect the cabin for any damage to doors, windows, seals.
3.| Please remove dust & debris from shoes and clothes before entering the cabin.
4.| Ensure door(s) and windows are closed correctly.
5.| Start engine and turn HVAC on to speed 2 (medium speed).
6.| After fixed speed delay, the Breath Safe display will show 50 Pascals or pre-set value.
The system is working correctly when the pascal value is green.

> > There is no further action required < <

NORMAL OPERATING CONDITION

Cab Air Conditioning
Breath Safe recommends OEM air conditioning fan is set at mid speed or greater to circulate air around the breathing zone and minimise CO₂.
Acceptable operating range for Breath Safe fan 10-80%. >80% recommend maintenance.

ALERTS

Fixed Fan Start Delay
Allows the operator to carry out pre-start checks – limiting at 30% fan speed, press the red text to disable.
CO₂ Level Alert (if equipped)
Ensure air conditioning fan is set at mid speed or greater to circulate air and minimise CO₂.
Low Pressure Alarm

Cabin is not maintaining positive pressure – check doors and windows are closed correctly.
Refer to maintenance department to check filters and cabin sealing. Ensure filters are serviceable.

Check Filter

Reminder to inspect or replace filter. Service hour meter requires re-set.
Refer to maintenance department.

SPECIFICATIONS HIGH-CAPACITY HEPA PRESSURISER

List of Abbreviations

PARTS LIST – TL4 24V DC PRESSURISER UNIT

Item No.	Qty.	Description	Part No.
1	1	Pre-cleaner Hood & Rotor Assy	200004
2	4	Pre-cleaner Injector Ring	200005
3	1	TL Fan Blade (inc. in #7)	200006
4	1	TL Nose Cone / Pre-cleaner	200007
5	1	TL Motor Housing	200008
6	1	TL Filter Housing	200009
7	1	24v DC Brushless VSD Motor & TL Fan Blade	200002
8	1	O Ring Seal Kit 2 Parts	200010
9	1	Included in 8	200011
10	1	Wiring Sleeve	200012
11	1	HEPA H14 Filter	500000
12	3	M6 Nyloc Nut	300218 (M6NYL)
13	3	M6 x 55mm Hex Bolt	300982 (M655B)
14	4	M8 x 190 Hex Bolt	301136 (M8190B)
15	8	M8 x 22mm O/D HD Washer	300230 (M8222HTW)
16	4	M8 Nyloc Nut	300249 (M8NYL)
17	5	M4 x 75mm Pan Head Phillips Screw	300162 (M475PBH)

PRESSURISER ASSEMBLY No : 200000

PARTS LIST GA

Item No.| Part No.| Rev| Description| Qty| Colour| Category
---|---|---|---|---|---|---
1| 16877| 0| Pressurizer Assy| 1| Satin Black MX88-124| Module
2| 11941| 1| F/A Inlet| 1| Satin Black MX88-124| Weld Assy
3| 16873| 0| Pipework and Ducting Assy| 1| Satin Black MX88-124| Pipework
4| 12011| 0| R.A.F Assy| 1| Satin Black MX88-124| Assembly
5| ST100101| []| Controller LRG STD Box| 1| (As Per Assembly)| Stock Item
6| 200202| []| TS Controller Assembly| 1| –| Stock Item

PARTS LIST – PRESSURISER MODULE

Item No.| Part No.| Rev| Description| Qty| Colour| Category
---|---|---|---|---|---|---
1| 14671| 0| TL Support Assy| 1| Satin Black MX88-124| –
2| 250007| 0| STD TL Mount with M8 Nuts on Outer Holes| 1| (Per Assembly Colour)| –
3| 200000| [*]| TL4 24V DC Unit| 1| –| Stock Item

PARTS LIST – PIPEWORK MODULE

Item No.| Part No.| Rev| Description| Qty| Material| Thickness| Category
---|---|---|---|---|---|---|---
1| TQM DP1290| 1| Under wheel Duct Assy| 1| (Prt Dwgs)| (Prt Dwgs)| –
2| 76ODSS500| –| 76.3 x 1.6 @500mm| 1| Stainless Steel Tube| 3.0”ODx1.5W/T| Pipework
3| 300388-0400| –| 76.3 x 1.6 @400mm| 2| Stainless Steel Tube| 3.0”ODx1.5W/T| –
4| 76ODSS70| –| 76.3 x 1.6 @70mm| 3| Stainless Steel Tube| 3.0”ODx1.5W/T| Pipework
5| 300848| N/A| 3” Cobra Neck| 1| –| N/A| Hardware
6| 200306| –| 3” – 45deg Short Elbow| 2| Silicone| –| Pipework
7| 200306| –| 3” 45deg Short Elbow| 2| Silicone| –| Pipework
8| 200308| –| 3” 90deg Short Elbow| 2| Silicone| –| –
9| 3” Stauff| 0| 3” Stauff Clamp Assy| 2| (Prt Dwgs)| (Prt Dwgs)| –
10| 16874| 0| Stauff Mount Brkt 1| 2| Mild Steel| 6| Part
12| 16875| 0| Stauff Mount Brkt 2| 2| Mild Steel| 6| Part
13| 16876| 0| Template| 1| Mild Steel| 3| Part

PARTS LIST – MONITOR MOUNT

Item No.| Part No.| Rev| Description| Qty| Colour| Category
---|---|---|---|---|---|---
1| ST100101| [*]| STD Large Monitor Box| 1| –| Stock Item
2| 200027| N/A| INPRESS TS Controller CO2 Sensor| 1| –| Stock Item
3| 200031| N/A| CO2 Sensor Suit 200027| 1| –| Stock Item

TECHNICAL DETAILS

Display Key Features

Digital cabin pressure monitoring system
Automatic cabin pressure control
Intelligent fan speed output
Data logger
Alarm for low-pressure (RS20)
Light sensor for automatic dimming of the screen

CO2 Sensor

CO2 Sensor Type is NDIR (Non-Dispersive Infrared)
Sample Rate is every 2 seconds
12-30V DC Operating Voltage
Automatic Altitude Compensation
Alarm Set points are adjustable
No setup required

Connections : 200027

Item	Destination
1	PIPE A – AMBIENT PRESSURE – OUTSIDE
2	PIPE B – POSITIVE PRESSURE – INSIDE
3	RJ45 CONNECTOR – CO2 SENSOR
4	OVERRIDE TOGGLE SW = MAX SPEED

Item	Destination
1	12/24 VOLT POSITIVE SUPPLY
2	CAN H OPTION
3	CAN L OPTION
4	SERIAL TRANSMIT RS232
5	MOTOR CONTROL VOLTS OUT
6	ALARM + OUTPUT
7	TEMP SENSOR
8	NO CONNECTION
9	SERIAL RECEIVE RS232
10	DOOR INPUT (+)
11	WINDOW INPUT (+)
12	0V NEGATIVE GROUND

Wiring Diagram

SMOKE EMITTER CABIN PRESSURE LEAK TEST

Do not handle until MSDS & all safety precautions have been read and understood. Use personal protective equipment as required.
Before use, carefully read the product label. Safe work practices are advised to avoid eye or skin contact and inhalation. Observe good personal hygiene, including washing hands before eating. Prohibit eating, drinking, and smoking in contaminated areas. Avoid inhalation. Mechanical extraction ventilation is recommended when the removal of atmospheric contaminants is required. Maintain dust / fume levels below the recommended exposure standard. For small amounts, absorb with sand, vermiculite or similar and dispose of at an approved landfill site.

WARNING

For Professional Use Only – keep out of reach of children.
Do not ignite near or around flammable materials.
Use only in well-ventilated areas, outdoors, and/or with proper respiratory protection.
Persons with respiratory sensitivity should avoid exposure to any smoke.
Concentrated smoke may cause severe burns to the skin, eyes, or respiratory system.
Improper use may result in sufficient inhalation of smoke to cause respiratory tract irritation and lung damage.
Harmful if swallowed.

DANGER
Use only as directed. Do not handle until all safety precautions, including Safety Data Sheet, have been read and understood. The product contains hexachloroethane. Wear protective clothing. If exposed or concerned, get medical advice. Store in a cool, dry, secure location. KEEP OUT OF REACH OF CHILDREN. Dispose of contents/container per location regulations. When used as directed, exposure should be limited and usually poses no hazard because the hexachloroethane is consumed inside the tube as smoke is produced.

Directions: (Smoke Bomb)

1.| Ensure other workers in close proximity are informed of use. Place on a non-combustible container, away from flammable materials.
2.| Place at Blower intake, or upwind of target area, or near centre of space.
3.| Orient “Smoke Issues Here” toward air stream, away from surfaces. Place candle on a flame / heat resistance plate – if not it will melt into the plastic surface.
4.| Ensure smoke will not create any hazard where it is anticipated to go.
5.| Ignite emitter inside the cabin using site approved device i.e., solder torch or ‘lighter’ and conduct smoke test.
6.| Do not touch or hold smoke generator after ignition – item becomes very hot & remains hot after use.
Smoke Emitter Cabin Pressure Leak Test

1.| The pressurizer system is switched on (TEST MODE).
2.| Hold the smoke emitter angled down.
3.| Ignite emitter using site approved ignitor i.e., solder torch or ‘lighter’.
4.| When the product ignites, remove the lighter.
5.| If the product flames up, blow out the flame.
6.| Place the emitter in a non-flammable container and place it inside the cabin at floor level and close the door/windows.
7.| Observe smoke leaks to indicate worn-out or broken seal locations. Check leakage points outside the cabin.
8.| Do not come into contact with or inhale smoke haze.
9.| Wait until the smoke haze completely disperses before re-entering the cabin. Open door to allow sufficient ventilation of smoke prior to entering cabin.

*This SWP does not necessarily cover all possible hazards associated with this equipment and should be used in conjunction with other references. It is designed as a guide to be used to compliment training and as a reminder to users prior to equipment use.

Link to MSDS : SMOKE GENERATOR TQ7621AT30S.pdf

Personal Protective Equipment (PPE)

| Safety glasses must be worn at all times.
| Sturdy footwear with rubber soles must be worn.
| Respiratory protection devices may be required.
| Gloves may be worn.
Pre-operational Safety Checks
| Locate and ensure you are familiar with all machine operations and controls.
| Check work area and walkways to ensure no slip/trip hazards are present.
| Ensure the work area is clean and clear of any flammable material & fire extinguish device is present.
Ending Operations and Cleaning Up

| Leave the work area in a safe, clean, and tidy state.
Operational Safety Checks

| Ensure the machine is correctly isolated / immobilized.
| Ensure other persons do not inhale smoke haze.
| Take care and do not place a lit emitter close to a flammable surface.
Potential Hazards

CABIN SEALING TEST PROCEDURE

Cabin Sealing Efficiency Test Procedure

1| Start Engine – Pressurizer System is ON
2| Ensure all windows & door(s) are CLOSED correctly (no cabin pressure leaks)

NOTE : for a new cabin with effective seals, you may need to open a window slightly before closing the door to bleed the static cabin air pressure outwards. Once door is fully closed then close windows to begin testing.

3| Enter the Settings menu via the touch screen button.
4| Select and press the System Check button to go to System Test – Max Fan.
5| Record / photograph the maximum cabin pressure achieved.

COMMISSIONING PROCEDURES – CABIN PRESSURISER

Commissioning Procedures

Follow each step of the installation guide that was supplied with the BreatheSafe kit.
Cabin sealing is an integral part of RS20 & ISO 23875; you must ensure that cabin seals are adequate for maintaining positive pressure. In addition, the site (end- user) must have the correct procedure(s) for servicing
OPERATOR enclosure seals in a proactive manner rather than reactive. Items such as door and window seals must be in good working order or new seals FITTED before the Breath Safe system installation.
Touch-screen cabin pressure display/controller Part# 200027.
*System Check Function: enter the Settings menu option and select “System Check – Set Max.” The minimum Breath Safe requirement for cabin sealing efficiency is 250 pascals; if this result is not met, it is essential to re-examine and find pressure leaks of the enclosure and apply new sealing measures.
Submission for commissioning procedure as per the diagram below:

The commissioning images required are

ID plate / Machine Serial Number / Asset Number or Call Sign
INPRESS TL Pressurizer location
HEPA Return Air Filter Location Option: Powered Return Air Filter
Cabin Pressure Display Location – Including the “System Check” maximum cabin pressure result with motor output capacity %

Fill in the Breath Safe Service Tag with the following details

Machine Serial Number and Installers details
Date installed and System Check result (max cabin pressure)
The set cabin pressure with actual pressure and motor percentage output
Verify the 250-pascal threshold was achieved = pass OR not achieved = fail**

Please upload machine and installation details in conjunction with the required images. A Commissioning Certificate will be sent to the email address you nominate. **Extended warranty for (RS20 & ISO 23875) BreatheSafe Systems is only applicable to operator enclosures meeting this requirement.

BREATHESAFE SYSTEM TROUBLE SHOOTING GUIDE *TOUCH CONTROL

FAULT| POSSIBLE CAUSE| SOLUTION
*ERR error code*| Poor sensor connection| Remove & refit pod connection cable
Corrupted coding| Access factory setup – default reset – pin 6759
Check filter alarm| Service hour timeout| Access Check Runtime menu – reset hours via 7597 code
Temperature / CO2 error| Sensor not connected| Fit sensor or disable via site access CO2 & or temperature menu
Pressuriser running at full speed/noisy| Filter blocked| Service filter
Door or window open| Ensure doors & windows securely shut
Cabin sealing capacity not adequate| Perform pressure test procedure & seal leak points as required
Sense pipe blocked| Ensure clear & not bent
Internal sensor damaged| Replace controller
**No need to change setpoint
Filter blocking quickly| Defective cabin sealing| Perform pressure test procedure & seal leak points as required
Pre-cleaner failed| Check operation & replace if necessary
Display blank| Poor power supply| Check mains supply fuse & correct voltage
Check voltage & 20AMP supply/connections at pin 1 @ monitor
Check earth continuity at controller pin 12
Failed controller| Replace monitor
Controller showing 0.0 pressure| Fresh air filter blocked| Check filter condition & replace if required.
Low pressure alarm| Door or window open| Ensure doors & windows securely shut
Cabin sealing capacity not adequate| Perform pressure test procedure & rectify cab sealing
Pressurizer not operating| Ensure correct voltage 12v or 24v to pressurizer motor pin A
Check 1.6V – 10V present at motor Pin C
Check 20A Supply fuse
Check earth continuity Pin B
Pressure sense tube blocked| Unplug at monitor & ensure clear flow to external of cabin
Ensure pressure tube fitted correct port A
**No need to change setpoint
Pressurizer not working| Poor power supply| Check 20A mains fuse & correct voltage
Ensure adequate wire size & no voltage drop
Ensure correct voltage 12v or 24v to pressurizer motor pin A
Check 1.6V – 10V present at motor Pin C
Poor earth| Check earth continuity @ motor pin B
Motor faulty| Replace TL4M
Access Codes:| Site Access: 7597| Factory Setup: 6759**

USER SETTINGS INSTRUCTIONS

User Settings Instructions
ENTER SET UP MODE
Start-Up Screen > Main Screen > Settings Button > Settings Screen > Site Access Button > Insert Pin > Site Menu

To enter the Setup mode, press the SETTING button.
Then enter SITE ACCESS MENU. Type in 4-number pin and press ENTER.

SET UP PARAMETERS
Placing the Breath Safe 200027 unit into Setup mode allows the adjustment of the following parameters

Time (hours/minutes/seconds)
Date (day/month/year)
Pressure alarm setpoint
Preferred cabin pressure
Alarm delay/ intervals of alarm
Calibration and system settings
Resetting of the data logging
Service reminders interval gap
Reset current runtime between services
CO2 settings and alarms

PRESSURE SETPOINT
The pressure setpoint changes the pressure that the cabin will be maintained. INPRESS TS maintains the pre-set pressure within the cabin compared to outside.
Enter Setup mode and select ADJUST SETPOINT button. Then, use the onscreen UP and DOWN buttons to change the corresponding fields.

PRESSURE ALARM SETTING
The mining industry benchmark for cabin pressure is 50 pascals and low- pressure is set at 20 pascals.
After a delay the alarm will activate if cabin pressure remains below the pre- set value. Enter Setup mode and select ADJUST SETPOINT button. Then, use the onscreen UP and DOWN buttons to change the corresponding fields.

SERVICE INTERVAL
Use the onscreen UP and DOWN buttons to change the service interval setpoint.
To reset the current runtime to zero, press the RESET CURRENT RUNTIME button and enter the site access pin.

DATE & TIME SETTINGS
Change the recorded date displayed and measured by the INPRESS TS.

ALARM BUZZER SETTINGS

PRESSURE ALARM BUZZER SETTING
To disable the buzzer, toggle through to the ENABLED and DISABLED buttons.

CALIBRATE ZERO SENSOR
Over long runtime, the 200027 may need recalibration. This screen allows the sensor to be recalibrated if more than 5 Pascals are out. To recalibrate, open windows and doors, turn off air conditioning, and any other device that may alter cabin pressure. Then, press the AUTO ZERO SENSOR button and leave the cabin while measuring. This process will reset the Zero Pressure.

CO2 SETTINGS

CO2 MODULE ENABLE/DISABLE
Enable or disable to CO2 module used for measuring CO2 levels within the cabin.

CO2 PRIMARY ALARM POINT
The first alarm will sound when CO2 levels inside the enclosure reach this point.

CO2 ALARM DELAY
After CO2 (concentration in ppm) within the cabin reaches the 1000 ppm setpoint, the alarm will sound after this designated amount of time. The Alarm Delay adjusts the time between the INPRESS TS measuring CO2 concentration and sounding the alarm. Use the onscreen ADJUST buttons to change the corresponding fields. For example, press to toggle through Disabled / 1 – 10 minutes.

CO2 CRITICAL ALARM MUTE RESET
The critical alarm is set at 2500 PPM and cannot be changed. The mute delay, however, can be configured.

DATA DOWNLOAD

Data Download – Setting up RS232 Connection

Plug the RS232/USB adaptor into a free USB port on your computer.
Open up TeraTerm software.
(TeraTerm is an open-source software tool and easily accessible via online search)
Use the following settings in TeraTerm: Serial and choose the correct port connection
Hint
Click on the COMxx Port with the “USB serial Port” connection from the drop- down menu.
Example
COM 21
This connection may be different on your computer.
Click OK once the correct communication port has been identified.
Go to SETUP and click on Serial Port.
Change the COM ports to the following configuration
Baud
Rate : 57600 Data : 8 bit
Parity : EVEN
Stop : 2 bit
Flow Control : NONE Data Download – Setting up RS232 Connection
If required, you may choose to save the COM port settings. Go to Settings and clock save the setup.
Hint : From the drop-down menu, click on the Save Setup.
Name the file and save it.
The next time a download is required, you may restore the setup, and the required COM PORT settings will be loaded, ready to download the data file from the 200027 unit.
From the drop-down menu, click on the Save setup.
Click Restore setup.
Choose the file name you have already saved.
From the drop-down menu, click on the Edit menu function.
Press “Select All”.
Select “Copy table”.
Open a blank excel document and click on the page. Then, right-click to paste the copied table.
Fields are
Date, time, motor (volts) output, cabin pressure (Pa), cabin pressure pre-set (Pa), low cabin pressure alarm
(Pa).

Excel Data Instructions – Unformatted

Open an Excel sheet and select the first cell A-1. Next, press and hold down the CTRL button on your keyboard and then press the letter V on the keyboard.
This procedure will paste the copied data onto that Excel sheet. Once that data has been pasted onto the Excel sheet, click on ‘DATA’ on the pull-down menu, followed by ‘Text to Columns’. Next, select ‘Delimited’ on the newly
opened window and click on Next.
Only select the ‘Comma’ button in the next window and then click ‘Finish’.
Then, the Excel fields will update such that each piece of data is placed in the correct columns.
The data is now ready for archiving.

Data Logging Formats

BU No : xxxxxx (the device number unique to each unit and used for identification – format = 000000)
Time : [09:25]
Date : [25/07/12]
Pressure : 32 (Pascals) as an example.

Alarm Type

0| = No alarm
1| = Low-pressure alarm
2| = Window open
3| = Door open

INPRESS TL WARRANTY

Express Warranty
All Breath Safe products carry a warranty against defects in materials or workmanship, provided the
defects are not from factors outside of Breathe Safe’s control (including neglect, lack of maintenance,
improper installation or operation, unauthorized servicing repair, etc.). Breath Safe will replace goods defected in material or workmanship at our Queensland factory or designated branch*. All parts deemed as failed or faulty must be returned to Breath Safe for evaluation unless otherwise stated in writing.
Note – Systems must be installed and commissioned as per Breath Safe installation and commissioning instructions. Once commissioned, the online commissioning sheet must be filled in, extending the components warranty as below. In addition, the system must be serviced and maintained correctly and by trained and qualified personnel. This requisite includes Breath Safe technicians, qualified automotive air-conditioning technicians, or qualified auto electricians.

Warranty period – Standard

1 year or 10,000 hours (whichever occurs first).
Controllers – 1 year no extended warranty option.
Warranty Period Extension when commissioning documents are registered online within 28 days of installation
Extended warranty** only offered if commissioning maximum pressure test reaches at least 250Pa.
Brushless motor fixed speed two years, or 10,000 hours (whichever occurs first).
Variable speed brushless motor 15,000 hours, or 3 years** (whichever occurs first).

Must be supplied with a variable speed pressure controller, data download required for 3-year warranty option. Link to online Commissioning and Extended Warranty Registration form https://www.breathesafe.com.au/commission/

What is not covered under Express Warranty?

Failures are due to incorrect application.
Damage resulting from neglect, misuse, lack of maintenance, improper installation, or operation, inappropriate or abnormal use, accidental or unauthorized servicing repair.
Failures are due to parts not being sold or approved by Breath Safe.
Failures arising from any other cause that is not directly related to a defect in material or workmanship.

This Express Warranty is VOID if the product is altered, modified, or used in the manner it was not designed for, also including unauthorized repairs, or using maintenance and repair parts other than those supplied by Breath Safe.

Breath Safe responsibilities

If there is a defect in material or workmanship not caused by the excluded failures during the warranty period, Breath Safe will either replace the defective goods at our Queensland factory, or designated branch. *
Alternatively, Breath Safe may elect to provide new replacement parts, Breath Safe approved repair parts or assembled components needed to repair the defect. Breath Safe reserves the right to provide a refund of the
purchase price in lieu of replacement or repair at Breath Safe’s discretion. The replacement or repaired product will be sent to you freight prepaid by the customer or made available for pick-up on site.

Users Responsibilities
The customer should ensure that the system is maintained according to Breath Safe service requirements and only authorized parts must be used to service and maintain Breath Safe systems. In the event of a suspected warranty claim, Breath Safe should be contacted in the first instance to arrange the repair or to assist with diagnosis. Claims should be made within one week of the repair.
After contacting Breath Safe, you may be required to deliver or send the parts to Breathe Safe’s
Queensland factory or designated branch. * Link to online Warranty claim form https://www.breathe-safe.com.au/warranty/

Exclusion and Limitations on Damages and Remedies

This warranty is provided in lieu of all other warranties, written or oral, whether expressed by affirmation, promise, description, drawing, model, or sample. To the extent allowed by law, all warranties other than this warranty, whether express or implied, including implied warranties of fitness for a particular purpose, are disclaimed. The maximum liability of BreatheSafe under this warranty shall not exceed the original purchase price of the product. Interference with the equipment by or abuse, or by operating the equipment at ambient temperatures or with electrical power characteristics outside the ranges indicated in our specification shall be excluded from this warranty, as shall consequential damages.
Excluded from any express warranty are costs incurred in relation to service outside our factory our designated service branch, including traveling time, waiting time, transport costs, mechanical and overtime payments required. As per Australian Consumer Law: You are entitled to choose a refund or replacement for major failures with goods. If a failure with the goods or service does not amount to a major failure, you are entitled to have the failure rectified in a reasonable time. If this is not done, you are entitled to a refund for the goods and to cancel the contract for the service and obtain a refund of any unused portion. You are also entitled to be compensated for any other reasonably foreseeable loss or damage from a failure in the goods or service.

*This express warranty gives you specific legal rights, and you may also have other rights that vary from country to country.