JBC Ds360 Micro Desoldering Iron Instruction Manual
- June 5, 2024
- JBC
Table of Contents
JBC Ds360 Micro Desoldering Iron
**Instruction Manual**
This manual corresponds to the following reference:
– DS360-A
Packing List
The following items are included:
Connection
Desoldering process
When desoldering, use a tip with a diameter larger than the pad being desoldered. This will achieve maximum suction and thermal efficiency.
The vacuum pump will continue to run for a few seconds. This makes sure that the vacuum circuit is completely empty. If there are any solder remains left on a terminal, just resolder it with fresh solder and repeat the desoldering operation.
Desoldering Iron Maintenance
Note : For the following operations, turn off the station or disconnect the tool and wait until the tool temperature drops to room temperature.
Changing Heating Element
Changing Iron Filter
Cleaning Solder Collector
Note : For this operations, turn off the station or disconnect the tool and wait until the tool temperature drops to room temperature.
Compatible Tips
The DS360 uses C360 tips.
Find the model that best suits your needs in
www.jbctools.com
Tip Care
To prevent tip oxidation cover tip with solder tin when not in use.
Note : Do not press the vacuum pump button while tinning the desoldering tip, as the fumes given off by the flux would quickly block the ducts and the air filter.
Changing Tips
Note: This operation should be done while the tip is hot and at a minimum temperature of 250°C, so that any tin left inside is still molten.
Cleaning Tips
The tip hole should be periodically cleaned.
Note : Let the tool cool down before performing this operation.
Choose the cleaning rod diameter according to the tip size. Put the rod at the tip, gently move it back and forth while turning it slightly.
Maintenance
Before carrying out maintenance, always switch the device off and disconnect it from the mains. Allow the equipment to cool down.
– Use a damp cloth to clean the tool. Alcohol can only be used to clean the
metal parts.
– Periodically check that the metal parts of the tool and stand are clean so
that the station can detect the tool status.
– Maintain tip surface clean and tinned prior to storage in order to avoid tip
oxidation. Rusty and dirty surfaces reduce heat transfer to the solder joint.
– Periodically check all cables and tubes.
– Replace any defective or damaged pieces. Use original JBC spare parts only.
– Repairs should only be performed by a JBC authorized technical service.
Safety
It is imperative to follow safety guidelines to protect health and prevent electric shock, injury, fire or explosions.
– Do not use the tool for any purpose other than soldering or rework.
Incorrect use may cause fire.
– Do not work on electrically live parts.
– The tool should be placed in the stand when not in use in order to activate
the sleep mode. The soldering tip or nozzle, the metal part of the tool and
the stand may still be hot even when the station
is turned off. Handle with care, including when adjusting the stand position.
– Do not leave the appliance unattended when it is on.
– It is necessary to turn the station off before changing tips.
– Heat can cause inflamable products to ignite even when out of sight.
– Be careful with the remains of liquid tin. Avoid flux coming into contact
with skin or eyes to prevent irritation.
– Utmost care must be taken with liquid tin waste which can cause burns.
– Be careful with the fumes produced when soldering.
– Keep your workplace clean and tidy. Wear appropriate protection glasses and
gloves when working to avoid personal harm.
– This appliance can be used by children over the age of eight as well as
persons with reduced physical, sensory or mental capabilities or lacking of
experience provided that they have been given adequate supervision or
instruction concerning use of the appliance and understand the hazards
involved. Children must not play with the appliance.
– Maintenance must not be carried out by children unless supervised.
Notes
Specifications
DS360
Micro Desoldering Iron
Ref.: DS360-A
– Total Net Weight: 176 g / 0.39 lb
– Package Dimensions / Weight: 300 x 125 x 65 mm / 341 g
(L x W x H) 11.81 x 4.92 x 2.56 in / 0.75 lb Complies with CE standards.
ESD safe
Warranty
JBC’s 2 year warranty covers this equipment against all manufacturing defects,
including the replacement of defective parts and labour.
Warranty does not cover product wear or misuse. In order for the warranty to
be valid, equipment must be returned, postage paid, to the dealer where it was
purchased.
Get 1 extra year JBC warranty by registering here:https://www.jbctools.com/productregistration/within 30 days of purchase.
This product should not be thrown in the garbage.
In accordance with the European directive 2012/19/EU, electronic equipment at
the end of its life must be collected and returned to an authorized recycling
facility.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>