TOPSKY DF02.01 Height Adjustable Desk User Manual

TOPSKY DF02.01 Height Adjustable Desk

DO NOT RETURN

We have a 1-year warranty: Within 1 year of receiving the package,  please contact our service team with Order ID. And if that is possible, pictures or detail of the issue will be helpful for a fast way solution.

How to contact with us
Email: [email protected] Customer Service Phone: +1 725-333-1988 http://www.topskyfurniture.com

You can check the installation guide from this YouTube video: https://youtu.be/s0RuSqx6iCQ
Or scan this QR code to check the video.

About how to use it, you can see YouTube video https://youtu.be/mrs0eqizyxg
You can also scan the QR code to check it:

Caution

• Keep children and pets away from the electric high-adjustable desk during the operation. Unplug the power cord during a thunderstorm or if you do not intend to use the desk for a long time.
• Make sure the desktop did not touch the wall.
• Ensure no obstacles in the desk’s path and no any object above 20” under the desk.
• Working environment temperature 0-40℃, keep products away from corrosive gas, liquid and dusty objects.
• It is strictly forbidden to disassemble the products privately to avoid the failure of the products or the damage to the human body caused by electronic products, etc.
• Although the product with anti-collision function, in order to avoid any pinching, please ensures that hands or other parts of your body are in a safe position during the operation. Anti-collision is not enabled during all resets.
• Please read the following instructions carefully before use the height-adjustable desk. The company does not bear any warranty or liability for damage and human injury caused by any abnormal operation.
• It is necessary to be reset manually after initial installation or power off.

BOM

M6*16 Screws Just For the Board Which Sold By TOPSKY.

Installation Instruction

STEP 1

• Set the right tube and left tube flat.
• Insert the extension tube to the right tube and left tube as is shown in the picture, pre-tightening the screws.

STEP 2

• Insert the columns into the place which is between the left and right
• tubes respectively, line up the holes on the frame and column.
• Fasten the screws.

STEP 3

• Mounting the side bracket on each side of the column.
• Fasten the screws.

STEP 4

• Line up the screw holes on the feet and columns.
• Fasten the screws.

STEP 5

• Check both sides of the desktop before placing the base on the bottom side of the desktop. Fasten the frame and handset to the desktop by tapping a screw.
  • Fasten the frame screws. And connect related parts as shown in below, including the control box, extension cable, and power cord.

STEP 6

• Install the handset on a suitable position of the desktop edge to avoid interference with humans or chairs.
• Tidy up all the power cables, and fasten with a cable clip.

Instruction

Manual Reset

1.  Keep pressing the “down” key till the display shows “E-1” and “rES” alternately and release the key.
2.  Keep pressing the “down” key again, the desktop will move slowly down and return back till the display shows “27.6”.
3. Release the key, the height-adjustable desk can be used normally.
4. It is necessary to be reset manually after the initial installation and power off.
   Note: The Anti-Collision function is not enabled during all resets. Please note that there is a potential risk of pinching in this case, and be sure no obstacles in the desk’s path.

Up and Down

1. Keep pressing the “up” key till the required height is reached.
2. Keep pressing the “down” key till the required height is reached.

Saving position

1.  Adjust the desktop to the height you want to save.
2.  Keep pressing the “S” key till the display will show “S – -“.
3.  Press the “1” key, and the display will show “S-1” and the current height alternately.
4.  Press the “S” key, the first memory position is set successfully. A similar procedure for “2” key and “3” key memory positions.

High and Low Limitation Positions

1. Keep pressing key “S” till the display shows “S – -“
2. Press the “up” key till the display flash as “HLP”.
3. Press the “1” key, the display shows “H-P” and current height alternately.
4.  Keep pressing the “up” or “down” key till the required high limit position is reached.
5.  Press the “S” key, the desktop height will be shown and the high limit position has been set.
6.  Repeat steps 1 and step 2 , then press “2” key, the display will show the “L-P” and current height alternately, keep pressing the “down” key till the low limit position is reached, and press “S” key, the low limit position has been set.

Change the displayed Unit(cm/inch)

1. Keep pressing the key “S” till the display shows “S – -“.
2. Press the “up” key, the display will show “Unt”.
3.  Press the “1” key, and the display will show “Unt” and the current height alternately, and the unit of height is “cm”.
4.  Press the “S” key to save the unit as “cm”.
5.  Repeat steps 1 and steps 2 , then press “2” key, the display shows “Unt” and the current height alternately, and the unit of height is “inch”, press “S” key to save the unit as “inch”.

Anti-Collision function

1.  Once the desktop encounters any obstacle in its path, the screen displays “E-2”.
2.  The desktop will move a defined distance in opposite direction, and it would be used normally after removing the obstacle.

Plug detection

1. Once the display shows “E-3” and “rES”, it reminds you to check whether any motors fail connected with the control unit. Please connect the main cable again, and wait at least 5 seconds.
2. Connect all the plugs.
3. Follow the “Manual Reset” procedure.

Reset to factory setting

1.  Keep pressing the “S” key till the display shows “FAC”.
2.  Press “S” key and the control unit restore to the factory setting (including memory position, high and low limitation positions, etc).

Code meaning and Troubleshooting

【Code meaning】

/ 102KG for further operation
E-2| Anti-Collision function| It can be used normally after removing the obstacle
dut| Operated continuously without suitable rest| Make the desk rest around 18minutes for further operation

【Trouble shooting】

refer to Manual reset
E-3| Check the cables and ensure they are well connected, and the height- adjustable desk can be used normally after manual reset

Technical Data

• company: CET PRODUCT SERVICE LTD. (for authorities only) Address: Chase Business Centre, 39-41 Chase Side
• Email:Info.[email protected]

References

• TOPSKYFURNITURE

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>