HAVIT HV3643T-BLK-12V 6w Lisse LED Down Wall Light 12v Outdoor Instructions

HAVIT HV3643T-BLK-12V 6w Lisse LED Down Wall Light 12v Outdoor Instructions

Model No.	HV3643T-BLK-12V	HV3643T-WHT-12V	HV3644T-BLK-12V	HV3644T-WHT-12V
Name	Lisse
Material	Aluminium
Colour	Black	White	Black	White
IP Rating	IP54
Input Voltage	12v DC
Lamp Base	Built in LED
Lamp Wattage	1x 6w	2x 5w
Colour Temp	TRI Colour – 3000k, 4000k, 5500k	TRI Colour – 3000k, 4000k,

HV3643 Dimensions

HV3644 Dimensions

This product must be installed by a qualified electrician according to AS/NZS 3000.
Ensure all electrical mains are disconnected before any installation.
Do not exceed maximum wattage restrictions for globes: 240V GU10 = 35w / 12V MR16 = 20w
Modification of this product will void any warranty.
Havit Lighting does not take responsibility for wrong installation, incorrect use, or use of installation material that does not belong to the system.
When installing low voltage fittings, Voltage to fitting must be within +or- 5% of voltage required and cannot be installed more than 25m from LED Driver, if not within this allowance warranty will be voided.
Aluminium and 304SS fittings must not be installed within 2km of any salt water environments.
When installing copper fittings, gloves must be worn to avoid any oils transferring to fitting.
All 316 stainless steel fittings must have regular cleaning maintenance to avoid any tea staining from forming on fitting. (Warranty does not cover Tea Staining)
All o-rings and seals must be in place correctly to maintain warranty.
These instructions may be updated at any time due to product improvements, Please visit website for most current installation instructions.

Make sure that the electrical circuit is free of voltage (master switch off )
Loosen allen screws on side of fitting
Remove base plate from fitting and attach base plate in desired location
Using an appropriate 12v DC LED Driver – DO NOT CONNECT LIGHT FITTING DIRECTLY TO 240V
Connect the cable – If more than one fitting installed, wiring must be done in parallel.
Fitting is preset to 3000k, to change slide switch to desired colour temperature
Reattach fitting to baseplate making sure screws are tight to avoid water penetration.
Apply silicon around edge of fitting to prevent any water from getting inside to electrical connections.
All connections must be carried out carefully, inspect all contacts before switching back on the electric circuit.

Must be installed by a licensed electrician

HV3643T-BLK

HV3643T-WHT

HV3644T-BLK

HV3644T-WHT

Model No.	HV3643T-BLK-12V	HV3643T-WHT-12V	HV3644T-BLK-12V	HV3644T-WHT-12V
Name	Lisse
Material	Aluminium
Colour	Black	White	Black	White
IP Rating	IP54
Input Voltage	12v DC
Lamp Base	Built in LED
Lamp Wattage	1x 6w	2x 5w
Colour Temp	TRI Colour – 3000k, 4000k, 5500k	TRI Colour – 3000k, 4000k,

HV3643 Dimensions

HV3644 Dimensions

This product must be installed by a qualified electrician according to AS/NZS 3000.
Ensure all electrical mains are disconnected before any installation.
Modification of this product will void any warranty.
Havit Lighting does not take responsibility for wrong installation, incorrect use, or use of installation material that does not belong to the system.
When installing low voltage fittings, Voltage to fitting must be within +or- 5% of voltage required, if not within this allowance warranty will be voided.
Aluminium and 304SS fittings must not be installed within 2km of any salt water environments.
When installing copper fittings, gloves must be worn to avoid any oils transferring to fitting.
All 316 & 304 stainless steel fittings must have regular cleaning maintenance to avoid any tea staining from forming on fitting.
(Warranty does not cover Tea Staining)
All o-rings and seals must be in place correctly to maintain warranty
This form may be updated at any time due to product improvements, please check online installation form for most current version.

Make sure that the electrical circuit is free of voltage (master switch off )
Loosen allen screws on side of fitting
Remove base plate from fitting and attach base plate in desired location
Connect the cable – use wire with earth; connect the earth first, then live and neutral wire
Fitting is preset to 3000k, to change slide switch to desired colour temperature
Reattach fitting to baseplate making sure screws are tight to avoid water penetration.
Apply silicon around edge of fitting to prevent any water from getting inside to electrical connections.
All connections must be carried out carefully, inspect all contacts before switching back on the electric circuit.

Must be installed by a licensed electrician