ATTACK SHARK X3 Light Weight Mouse User Manual

June 17, 2024
ATTACK SHARK

X3 LIGHT WEIGHT MOUSE
User Manual

Thank you very much for purchasing our product, and hope it can bring you a new operation and feeling. At the same time, we look forward to getting your valuable suggestions on our products, and we will continue to provide you with better products and  services.

PRODUCT DESCRIPTION

  1. Product model: X3
  2. Product interface type: USB-Type-C
  3. Product connection method: USB, 2.4G
  4. Product optical sensor: original phase PAW3395
  5. Transmission frequency:
  6. Return rate (HZ): 1251250/ 500/ 1000HZ default (drive adjustable)
  7. Frame rate (IPS): 650IPS
  8. Maximum acceleration (G): 50G
  9. DPI value and corresponding color: 800 (red)- 1600 (green)- 2400 (blue) -3200 (cyan)- 5000 (yellow)- 26000 (purple)
  10. Charging current: 280mA
  11. Charging voltage: 5V
  12. Product weight: 49g±3g
  13. Product size: 118.56139.7mm
  14. Data cable interface (length): Type-C/ 1.5 meters
  15. Wireless transmission distance: 10 meters
  16. Switch brand and service life: Kaihua 80 million times
  17. Support operating system: XP, Win7, Win8, win10, win11, Mac OS, Android, Linux etc.
  18. Sleep mode current: Light sleep (=0.3mA), deep sleep (=60uA)

BUTTON FUNCTION DESCRIPTION

  1. left button
  2. Right click
  3. Middle button
  4. Forward key
  5. Back key
  6. DPI cycle
  7. Short press the Bluetooth channel switch/ long press the 3 seconds to force the code key
  8. Power Toggle (2.4G-OFF)
  9. Receiver storage compartment
  10. Type-C interface
  11. Indicator lights: charging (purple), low voltage (flashing red), fully charged (green light is always on)
  12. DPI indicator light (tum off after 5 seconds)
  13. Mode indicator light: 2.4G (red)
  14. DPI: 800(red)- 1600 green (default)- 2400(blue)- 3200 (cyan)- 5000 (yellow)- 26000(purple)

Tips:

  1. Sleep mode
    (1) The mouse immediately enters a light sleep after it stops working.
    (2) The mouse enters deep sleep without any operation for 10 minutes.

  2. Sleep wake-up method
    (1) Light sleep, wake up by moving.
    (2) Deep sleep, press key to wake up.

  3. Hardware connection: Insert the USB plug of the product into the port of USB 1.1 or above (when the product is used for the first time, the bottom right corner of the computer will pop up an automatic hardware installation prompt).

CONNECTION MODE

Wired mode connection method: ATTACK SHARK X3 Light Weight Mouse - Figure
2

Use the included TYPE-C cable to connect to the computer. When the cable is plugged in, switch the mouse to “OFF for wired mode. Move the mouse and the computer screen pointer can move, and the mouse can be used normally.

2.4G connection method:

ATTACK SHARK X3 Light Weight Mouse - Figure 3

Plug the receiver into the computer USB port
The computer will automatically install the configuration software ATTACK
SHARK X3 Light Weight Mouse - Figure 4

If the connection is blocked or the signal is lost, please repeat steps 1,2, and 3. Then code again.
Code matching method: Press and hold the 7 code button for about three seconds, the 2.4G channel light will flash red quickly. When the pairing is successful, the light will be steady red for 1 second and then turn off, and the mouse is in normal use.

PRECAUTIONS

It is forbidden to immerse the mouse in liquid or spray the mouse with liquid
It is forbidden to use the mouse in high temperature and high humidity environment
Do not place the mouse in an open flame
Violence against pressing the mouse is prohibited
Do not disassemble the mouse

PACKING LIST

ATTACK SHARK X3 Light Weight Mouse - Figure 5

FCC Warnning:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection againstharmful interference in a residential installation. This  equipment generates, uses and can radiateradio frequency energy and, if not installed and used in accordance with the instructions, maycause harmful interference to radio communications. However, there is no guarantee thatinterference will not occur in a  particular installation. If this equipment does cause harmfulinterference to radio or television reception, which can be determined by turning the equipmentoff and on, the user is encouraged to try to correct the interference by one or more of thefollowing  measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

Caution: Any changes or modifications to this device not explicitly approved by manufacturer could void your authority to operate this equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause  undesired operation.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 0cm between the radiator and your body.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals