EURO-PRO EP93 Vapor Steam Cleaner Instructions

Vapor Steam Cleaner
1500 Watt
Model EP93

USE & CARE INSTRUCTIONS

EP93 Vapor Steam Cleaner

Congratulations! You are the owner of the ultimate in modern Vapor Steam Cleaning equipment. To fully enjoy the advantages of your appliance, please take a few minutes to read all the “Use & Care Instructions” and keep the instructions handy for ready reference. Please review the product warranty and mail the owner registration form.
EURO-PRO Corporation , 178 West Service Rd,. Champlain, NY 12919 514-842-8691
OMEGA SEWMAC Inc., 3445 Park Avé., Montreal, Quebec, Canada H2X 2H6

110 volts, 1500 watt

1 – Safety Cap for Steam Generator / Water Tank
2 – Push On/Off Switch for the System
3 – Steam On Light
4 – Add Water Light| 5 – Power Cord
6 – Steam Cleaning Unit
7 – On/Off Steam Switch
8 – Steam Strength Regulating Knob
---|---

List Of Accessories

9 – Extension Tubes
10 – Rectangular Brush for Floor /Carpet
11 – Triangular Brush
12 – Angle Adapter| 13- Glass & Tile Squeegee
14 – Detail Cleaning Attachment (on the photo small brush is attached)
15 – Small Nylon Detail Brush
16 – Water Filling Funnel
---|---

Technical Specifications

Operating Instructions – Components

On/Off S witch:
The unit is “On” when the switch (#2) is inthe “Pushed down” position. The unit is “Off” when the switch is in its “Up” position.

safety Cap (#1)
In order to open the Safety Cap, first press it down and then turn counter clockwise.
Caution: Read the instruction for“ Filling the Water Tank’before opening the Safety Cap.

Steam Strength Regulating Knob (#8)
This knob adjusts the amount of steam coming out of the nozzle. Turning the knob clockwise will increase the steam flow to its maximum.
Steam Indicating Light (Yellow) (#3)
When this lightis “On”, it indicates that the steam is ready to use. Important: This light willgo “Or! and “Off? during usage showing that the steam is being generated.
Add Water Light (Red) (#4)
This light will go “on” when the water level is low.
Important: Before adding water, read the instructions for adding water.
Depending on the ambient room temperature, this light might go on for a short period during initial tank heating.
On/Off Steam Switch (#7)
Setting this switch to the “On” position will start the flow of steam.
Caution: The On/Off Steam Switch located on the handle must be in the “Off position before attaching or disassembling accessories.
Starting Your Vapor Steam Cleaner
CAUTION: Do not plug in the machine during filling. Use a grounded receptacle. Use only a heavy duty extension cord rated for 15 amps – Do not use an ordinary extension cord.

Filling Your Steam Generator With Water

Step 1: Press down Filler Cap (#1) and turn counter clockwise until removed.
Step 2: Place Filler Funnel in tank and add two quarts of clean tap water. Do not overfill.
Replace Filler Cap by turning clockwise – press down firmly to tighten. It is ok to use hot water. This reduces heating time.
Step 3: Plug the machine into a standard 120 volt wall (3-prong) receptacle. Depress Heater On/Off Switch (#2).
Step 4: Allow approximately 10 minutes for vapor to reach its working temperature and pressure. When these have been reached, the Yellow indicator (#3) will light.
The machine is ready to operate.
Step 5: Add desired attachments. After attachments are in place, activate vapor flow by pressing the Or/Off Switch (#7) on the handle. Note: After you start using steam, the Yellow Indicator (#3) will go out. If you stop the use for several minutes, the Yellow Indicator (#3) will go back on.
Step 6: At the start, some water will come out from the nozzle of the attachment. This is unheated water in the hose.
Step 7: Adjust the pressure control knob (#8) to the desired pressure. Heat does the cleaning! Use the lowest pressure possible to do the specitic job.
A. Depending upon the ambient temperature, this Red Waking indicator (#4) might light up during the initial tank heating. Go ahead and vent the hose and Start use. After approximately 2 to 3 minutes of use, this indicator will go out.
Continue normal use.
B. The Red Indicator (#4) functions as a low water warning. When your vapor pressure significantly decreases and the Red Indicator (#4) lights, release all pressure through the nozzle by pressing Steam Switch (#7) to“On”and allow the machine to cool. To refill, repeat steps #1 through #6.

If the “Add Water” Light (#4) Turns “On” During Cleaning, Indicating Low Water Level, Follow the Instructions Below to Refill the Steam Generator.
Step 8. Push the On/Off Switch (#2) to its “Off’ position
Step 9. Push the On/Off Steam Switch (#7) to its “On” position to release all the steam left in the steam generator, then turn the switch to “Off position.
Step 10. Unplug the power cord (#5) from the wall socket.
Step 11. Follow instructions to fill the Steam Generator as shown above in Step #1.
Caution: When refilling the machine while it is still hot, the first drops of water might bubble up.

Using Your Accessories

Attaching the extension tubes (#9) to the Pistol Grip (with On/Off Steam Control) and to the other accessories.

To insert the extension pipes (#9) one in the other, in a the flexible pipe grip and in the attachments, press the knob ensuring that it fits into the hole. To disconnect, repeat this operation by pressing the knob and pulling on the two parts.

Note: The angle adapter (fig. 1) is already attached to the rectangular brush (fig. 3) but can be removed and used also with the triangular brush (fig. 2).

Attaching the Angle Adapter
Attaching the Angle Adapter (fig. 1) to the brush for floor and carpet (fig. 3), and the triangular brush (fig. 2)
Hold the brush with its bristles pointing down in your left hand. With the “Angle Adapter” (fig.1) pointing downward, isert it into the hole in the back of the brush, then turn the “Angle Adapter’ (fig.1) 180°.
Removing the Angle Adapter
To remove the angle adapter from one brush to insert to the other:
Hold the brush (fig.2 or fig.3) with its bristles pointing down in your left hand. Turn the adapter (fig. 1) 180° (pointing downward) and then pull.

Attachments

Brush for carmets/floor (#10).
100% white terry cloth towel can be fitted on this brush as to absorb the dirt and protect delicate surfaces. It can also be used on vertical washable surfaces following the same procedure as for the floor.

How to fit the Towel Over the Rectangular Brush (#10)

1. Prepare white terry cloth towel: size 8 x17″

2.  Place the brush on top of the towel

3. Fold the towel as shown in Fig. B

4. Fold the other side of the towel as show in Fig. C.

5. Place the corner under the cloth holder as shown in Fig. D.

6. Stretch the towel around the brush, and repeat folding the towel as shown in Fig. E.

Triangular Brush (#11),
This same attachment too can be used with 100% white terry cloth towel same as for the carpets/floors brush. Very effective for cleaning under furniture or hidden corners.

How to Fit the Towel over the Triangular Brush (#11)

1. Prepare white terry cloth towel, 8” x 17°

2. Fold it into two (Fig. F & G)

3. Place the triangular brush on the towel. (Fig. H)

4. Fold the towel as shown in Fig. I.

5. Place the corner under the cloth holder. (Fig. J)

6. Fold the other side of the towel in the same way and place the comer under the doth holder (Fig. K & L).

Glass & Tile Squeegee
This attachment is very useful for cleaning large windows, plastic material, ceramic, tiled surfaces, marble planes, etc.
Apply steam abundantly, rub with the spongy side and remove with the glass wiping rubber.

Detail Cleaning Attachment (Spray Nozzle #14)
This attachment is very useful for cleaning surfaces that are difficult to reach. It is ideal for radiators, door and window jambs, shutters and Sanitary fixtures. The following parts can be applied to this attachment:
– round mini-brush (#15)
screw the mini-brushes on the thread end of the Spray nozzle (#14).

Nylon Detail Mini-Brush (#15)
it is best for cleaning in-between the _ tiles, ceramic, marble, wooden floors.

Tips On How To Use Your System

Water

• Use tap water for all your cleaning needs.
• However if you live in an area with hard water, use demineralized/distilled water when cleaning light colored fabrics to eliminate the possibility of hard water stains.

Temperature

• The vapor temperature at the tip of the nozzles is between 220°F and 240 °F.
• The temperature of the vapor falls to 100 °F at a distance of 10 inches from the nozzle.

Warning: A towel wrapped around the brush can become hot enough to burn. Make sure that you let the towel cool off before touching it.

Adjusting Steam Pressure (with knob #8)

• Start cleaning with low steam pressure.
• Increase the steam pressure only if the surface being cleaned requires it.
• Using steam on low or medium setting will extend the time your can use your unit before refilling it with water.

Using Towels

• For best results use 100% cotton white terry cloth towels.
• Use correct size of towel to allow you to wrap the towel around the brushes and clip it under the springy cloth holder.
• The purpose of using a towel is to absorb moisture and dirt being cleaned. Use always dry towels. A wet towel will smear the dirt.
• Wash towels with string detergent and bleach.
• Using scented fabric softener while washing the towels will cause the scent to be released into the air when using the towels with your steam system.

Efficient Work

• Wipe always from the top down, in this way the dirty drops will not dirty surfaces already cleaned.
• Avoid changing brushes back and forth while cleaning.
• Start with the smallest brush to clean tight spots and corners first.
• Wipe dirt as soon as possible, otherwise it will dry and stick to the surface.

Using Your Vapor Steam Cleaner

Wood, Vinyl and Marble Floors
Use the large floor brush with a terry cloth attached. Move the brush across the floor as if you are mopping. When the towel is soiled, you can turn the towel over or replace it with acle an towel. If you are working on a very dirty area, you can move the brush over the area slowly, several times. If it is a wood floor, move fast to avoid heat or moisture build up in the wood. By cleaning with the towel over the brush, you will not affect the shine on the floor.
To Strip Wax : Use medium or high pressure, triangular brush for open areas; small nylon detail brush for corners or tight areas – no towel, slow strokes. Work a small area at a time – remove the emulsified wax from the floor. When all of the wax has been stripped, immediately clean the floor and brushes with water before residue has a chance to harden on them. Go back over the stripped area with the triangular brush with a towel to remove any remaining residue before waxing.
To Clean Waxed Floors: Use low pressure setting, wrap clean towel around the triangular brush, brush quickly. This will cause the dirt to be removed.
Vinyl Floors: Do not allow heat to buildup in any kind of vinyl, since it can soften it enough to affect its texture. Work fast on vinyl.
Tile Floors: Use a detail attachment with the small nylon detail brush attached to an extension. Have the large floor brush with cloth attached ready as well. Clean the grout of the tile with the small nylon detail brush. Remove the detail attachment and attach the large floor brush/ move the brush across the floor to clean the tile and remove excess moisture and residue. For areas of tile that are very dirty, remove the towel and agitate with the brush. Do not let the area dry before you wipe it up.

Carpets
Vacuum the entire carpet area first. Use the large floor brush with a cloth attached (you might need two terry cloth towels to eliminate drag). Move slowly over the area allowing the vapor to penetrate the carpet. The cloth will absorb the excess moisture and residue. For smaller areas, the triangular brush can be used with a cloth as above. For spot cleaning, use the detail attachment without a brush.
Remember – the towel is your ‘extractor” in this process. Do not vacuum again while the cleaned area is still warm. Do not linger too long in one place – norma! back and forth motion used in cleaning a carpet prevents heat buildup in the fibers.

Warning

• Do not vacuum the carpet while it is still warm. The dirt from your vacuum cleaner may be re-deposited into the carpet.
• Some carpets do not have secured colorfast dyes. Do not start cleaning your carpet before testing first in a small inconspicuous area.

Upholstery
Use the triangular brush with a clean white terry cloth towel. Use only low pressure when cleaning any kind of fabric. Use fast, light strokes, avoid getting the fabric wet. When cleaning silk, warm up the towel and then turn off the vapor entirely before touching the fabric – if the towel is too hot to touch with your hand, it is too hot for silk. Be patient with stubborn spots; work on a spot gently for no more than a minute at a time, then wait five minutes for the area to dry and repeat. Use circular movements or back and- forth and side-to-side movements to get all sides of surface fibers. Finish with a brushing in one direction that will give the fabric a uniform appearance.

Caution: Always determine the color-fastness of any fabric – especially with reds or blues – by taking a clean, moist, warm towel and gently rubbing a small area as far down on the back or other out of the way place on the furniture as possible. If color comes off on the towel, you may need to have the piece dry cleaned.

Walls
Use the large floor brush or triangular brush with a terry cloth towel depending on the Surface area to be cleaned. For painted surfaces, use the brush with a terry cloth attached to  remove stains or spots. Be sure that the paint is not a water-based paint that you are cleaning. The extreme temperature may damage the finish or even remove the paint.

Wall Paper

Vinyl or Normal Wall Paper – Use two terry cloth towels with the triangular or rectangular brushes to prevent bristles from poking their way through the towel while you are cleaning the wall- low pressure. Use smooth, rapid strokes.
Flocked Wall Paper – Use a nozzle with no brush – low heat. Blow dirt and dust from the surface from a distance of 1” -t 1/2” to the side. Follow up with the triangular brush, two terry cloth towels. (Heat the terry cloth towels up enough to make them moist and turn off the vapor before touching the wall paper.)
Note: Use only low pressure and lean quickly while you are cleaning any kind of wail paper.

Ceilings
Use the large floor brush with a terry cloth towel attached. Clean painted ceilings as you would clean a painted wall. If there is a heavy stain, you may expose the brush to get to an isolated area. Use caution where water-based paint exists.

Window, Glass Surfaces and Mirrors
Use the glass and tile squeegee. Work with the vapor jet downusing the top to bottom movements.
Use the squeegee with the vapor off to clear the water from the glass. To do this without leaving streaks, use lateral movements from the top to the bottom of the surface.

Fiberglass or Stainless Steel Surfaces
Use the triangular or small nylon detail brush. Slowly move the brush over the surface to be cleaned.
The vapor will emulsify the dirt and grease on the surface. Follow behind with a terry cloth towel over the brush to remove excess moisture and residue.
Tip: an old idea for polishing stainless steel is to wipe it down with seltzer soda water after it is cleaned.

Soap Scum
Soap scum dissolves almost immediately under a combination of heat and moisture. Use the triangular brush with a terry cloth towel clipped over it – medium pressure – and move quickly. Rinse the surface with a small amount of water afterwards or go back over it once more with a clean terry cloth towel.
Notes: Soap scum sometimes will develop a hard surface from waterborne minerals. If this is the case, use the triangular brush with no towel first to break up this surface – or spray or wipe first with lemon, vinegar or seltzer soda water to soften the minerals.
Moving too slowly can dry out the soap scum and cause it to granulate on the surface. The surface will have a gritty feel. If this happens, apply vapor to the surface with the open brush again and re-clean.

Garden Furniture
Use any of the brushes depending on the surface area.

Vertical and Horizontal Blinds
Use the triangular brush with a terry cloth towel. Move the brush over the surface, allowing enough time for the vapor to penetrate.

For badly soiled areas use the brush without the cloth first to loosen dirt

Bathroom Areas
To clean the bathtub or shower area, use the small nylon detail brush for grout, shower door tracks, hard to get areas and heavily soiled areas. The triangular or large floor brush with aterry cloth towel attached will be the most efficient way to clean the rest of the area. The Vapor Cleaner can be used to remove and kill mold or mildew build-up. Just allow plenty of time for the heat to penetrate the surface.
This is especially helpful in the shower area if there is tile or grout.
Removal of soap scum on tile, grout, and shower doors is also easier with the Vapor Cleaner.
To clean the toilet, use small nylon detail brush. Use a terry cloth towel or paper towel to wipe up excess moisture and residue.
To clean the sink, use small nylon detail brush. To clean the countertop, use the triangular brush with a terry cloth towel attached and wipe across the surface.

Exterior Areas
To clean your car, use the triangular brush with a terry cloth towel attached to clean upholstery and interior areas just as in the home. You should not expose the bristles to leather – use only the brush with the terry cloth towel attached. For detailing the wheels, use the detailing attachment, the small nylon detail brush or the triangular brush. Outer windows are cleaned best by applying the vapor with the small nylon detail brush and following with a paper towel.

To clean bicycles, use the small nylon detail brush.
To clean equipment, use the triangular brush, small nylon detail brush, depending on the surface area.

Real and Artificial Plants
Use the detail attachment without a brush attached to blow off the dust and dirt.

Clothing
A vapor cleaning system is excellent for removing wrinkles from fabrics. Set the steam level (knob #8) to minimum, increase steam rate as necessary. Simply “vaporize” the surface from about 1” away. The dry vapor removes wrinkles without leaving the fabric wet like ordinary fabric steamers do.
Removing shine from wool fabric – Use the triangular brush with terry cloth towel – low pressure – brush lightly in circular motion over entire area, then following the direction of the fibers.

Nicotine and Tar
Nicotine and tar dissolves at high temperatures and becomes a light yellow oil that has the consistency of sewing machine oil. When the nicotine/tar film is touched by a hot terry  cloth towel clipped over the triangular brush, it immediately dissolves and flows into the towel. You can remove it from flat surfaces as fast as you can move the brush over the surface.

Removing Wax, Tar, Etc.
Many stains are only stuck on the surface of materials and can be easily and quickly removed by “blowing” excess material away from the surface from the side. This is accomplished by using the detail attachment. Hold the terry cloth towel to the side to catch the loose residue as it is blown by the detailer. Note: Always vacuum any loose residue off the surface before you apply vapor to It.

Hints
The Vapor Steam Cleaner has many uses that are not stated above. This was meant only to give you a general idea of what can be achieved with the Vapor Steam Cleaner system.  However, the ways in which to use the attachments and brushes are in most cases universal. It is most helpful to always have a terry cloth towel or paper towel ready to use for removal of moisture and residue. 100% white cotton towels work best.
You can clean the brushes with your Vapor Steam Cleaner. For the larger pieces, hold at one end and use the detail attachment without a brush attached to simply blow off dirt into the garbage can. For the small detail brush, use a pair of pliers to hold and blow dirt as above or place in the basket of your dishwasher.
Use the Vapor Steam Cleaner for pet spots. It will clean urine and other stains, as well as odor, from the carpet and upholstery.

Note: Wipe immediately before the cleaned area dries. For the exterior of the oven, use the triangular brush with a terry cloth towel attached to clean around the dials, outlets, and switch plates. Use the nylon detail brush for cracks, crevices, and hard to reach areas.
Refrigerator – Use the nozzle to blow away dirt in the ice machine and on door seals. The vapor will not dry out or crack the seals as chemicals of tendon. Can openers and other kitchen equipment can be easily cleaned with the nylon detail brush on the nozzle to get into all the nooks and crannies.
Mold around door gaskets can be removed with the small nylon detail brush.
To clean microwaves or other appliances use the nylon detail brush for small areas and the triangular brush with terry cloth towel for larger areas.
To clean counter tops, use the triangular brush with a terry cloth towel attached. For heavily soiled areas, use the brush without the terry cloth towel first in order to loosen the debris, then follow with a terry cloth towel attached to finish.

LIMITED WARRANTY

EURO-PRO Corporation warrants this product to be free from defects in material and workmanship for a period of one (1) year from the date of purchase when utilized for normal household use by the original purchaser only. The attached Warranty Registration Card must be filled out and returned within 10 days of purchase. This is essential for your Warranty to be effective should any problem arise with this product.
Should any defect covered by the terns of the limited warranty be discovered within one year. EURO-PRO Corporation will repair or replace any defective part provided the unit is returned by the original purchaser, freight prepaid, to EURO- PRO Corporation, 178 West Service Rd.. Champlain, NY 12919. Proof of purchase date and $15.00 for handling and return packing/shipping charges must be included.*
The liability of EURO-PRO Corporation is limited solely to the cost of the replacement parts or the complete unit at our option. LABOUR CHARGES ARE NOT INCLUDED.
This warranty does not cover normal wear of parts and does not apply to any unit that has been tampered with or used for commercial purposes. This Limited Warranty does not cover damage caused by misuse. negligent handling. or damage due to faulty packaging or mishandling in transit (oy any common carner)
This warranty is extended to the original purchaser of the unit and excludes at other: legal and/or conventional ” warranties. The responsibility of EYURO- PRO Corporation , if any, is in. l. iv. specific obligations expressly assumed by it under the terms of the limited warranty. In no event is EURG-PRO Corporation liable for incidental or consequential damages of any nature whatsoever. Some States do not permit the exclusion or limitation consequential damages, so the above may not apply to you.
This warranty gives you specific legal rights which vary from state to state.

PURCHASER___
DATE OF PURCHASE _
DEALER ____
‘important: Carefully pack item to avoid damage in shipping. Be sure to attach man to item belore packing with your name, complete address and phone number with note giving purchase information model number and what you believe is the problem with item. We recommend you insure the package (as damage + in shipping is not covered by your warranty). Mark the outside of your package “ATTENTION CUS TOMER SERVICE.

https://manual-hub.com/

References

• Manual-Hub.com – Free PDF manuals!

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>