ICE i18B Industrial Floor Scrubber Dryer Instruction Manual

ICE i18B Industrial Floor Scrubber Dryer

Product Information

• Model: i18B/i18C Automatic Scrubber
• Manufacturer: ICE Cobotics (GuangDdong) Company Limited
• Address: XiangShi Road LiaoBu DongGuan GuangDong China
• Contact: Tel – 0769-81869000, Fax – 0769-81863000

Product Usage Instructions

Safety Precautions for i18B
This machine is intended for commercial use to scrub hard floors in indoor environments only. Follow these safety precautions:

1. Operate the machine only if trained and authorized.
2. Read and understand the operator’s manual before use.
3. Avoid operation in flammable or explosive areas.
4. Ensure the machine is in proper operating condition before use.
5. Avoid use in outdoor areas.

Safety Precautions for i18C
This machine must be grounded while in use to protect against electric shock. Follow these safety precautions:

1. Read and understand the manual before operating.
2. Ensure the machine is properly grounded during use.
3. Do not remove the ground pin from the plug under any circumstances.

FAQ (Frequently Asked Questions)

How do I order parts for the Automatic Scrubber?

To order parts, follow these steps:

1. Identify the machine model and serial number.
2. Use only ICE Cobotics Company supplied or equivalent parts.
3. Order parts online, by phone, by fax, or by mail.
4. Provide necessary details like part number, quantity, name, company name, customer ID, billing and shipping address, phone number, and purchase order number.

How should I dispose of old machine components?
To protect the environment, dispose of old machine components such as batteries and hazardous fluids in an environmentally safe way according to local waste disposal regulations. Always remember to recycle.

READ OPERATOR MANUAL CAREFULLY!

IMPORTANT:
To ensure full warranty protection, please fill out & return your warranty card.

Please fill out at the time of installation for future reference.

• Model No.
• Serial No.
• Machine Options
• Sales Rep.
• Sales Rep. Phone No.
• Customer ID Number
• Installation Date

HOW TO ORDER PARTS
Only use ICE Cobotics Company supplied or equivalent parts. Parts and supplies may be ordered online, by phone, by fax or by mail.

1. Identify the machine model.
2. Identify the machine serial number from the data label.
3. Ensure the proper serial number is used from the parts list.
4. Identify the part number and quantity. Do not order by page or reference numbers.
5. Provide your name, company name, customer ID number, billing and shipping address, phone number and purchase order number.

PROTECT THE ENVIRONMENT

• Please dispose of packaging materials, old machine components such as batteries, and hazardous fluids, including antifreeze and oil, in an environmentally safe way according to local waste disposal regulations.
• Always remember to recycle.

ICE Cobotics (GuangDdong) Company Limited

• XiangShi Road LiaoBu DongGuan GuangDong China
• Tel: 0769 – 81869000
• Fax: 0769 – 81863000

SAFETY PRECAUTIONS

This machine is intended for commercial use. It is designed exclusively to scrub hard floors in an indoor environment and is not constructed for any other use. Only use recommended accessories.

All operators shall read, understand and exercise the following safety precautions:

1. Do not operate the machine:
   • Unless trained and authorized.
   • Unless you have read and understand the operator’s manual.
   • Inflammable or explosive areas.
   • If not in proper operating condition.
   • In outdoor areas.
2. Before starting the machine:
   • Make sure all safety devices are in place and operate properly.
3. When using a machine:
   • Go slow on inclines and slippery surfaces.
   • Follow all safety guidelines.
   • Report and fix any damage to the machine before operating it.
   • Never allow children to play on or around the machine.
   • Do not operate on inclines that exceed 2%(3°).
4. Before leaving or servicing the machine:
   • Stop on a level surface.
   • Turn off the machine.
5. When servicing machine:
   • Read the operator’s manual thoroughly before operating or servicing this machine.
   • Use manufacturer-supplied or approved replacement parts.
   • Secure the machine with wheel blocks before jacking the machine up.
   • Use an approved jack or hoist to safely elevate the machine.
   • Disconnect batteries before working on the machine.
   • Wear gloves when handling batteries or battery cables.
   • Avoid any contact with battery acid.
   • Avoid moving parts. Do not wear loose-fitting clothing while servicing the machine.

WARNING:
Batteries may emit hydrogen gas. Explosion or fire can result from hydrogen gas. Keep sparks and open flames away! Keep the battery compartment open when charging(except for maintenance-free batteries).

• Flammable materials can cause an explosion or fire. Do not use flammable materials in tanks.
• Flammable materials or reactive metals can cause explosions or fire. Do not pick up.

WARNING:
Carefully read and understand this manual before operating this machine. This machine must be grounded!

This scrubbing machine shall be grounded while in use to protect the operator from electric shock. Grounding provides a path of least resistance for electric current. This machine is equipped with a cord having an equipment- grounding conductor and grounding plug. The plug must be plugged into an appropriate outlet that is properly installed and grounded by all local codes and ordinances. Do not remove the ground pin under any circumstances.

This machine is for use on a nominal 110-volt circuit and has a grounding plug that resembles the plug illustrated in Figure. Make sure that the machine is connected to an outlet having the same configuration as the plug. No adapter should be used with this machine.

This machine is intended for commercial use. It is constructed for use in an indoor environment and is not intended for any other use. Use only recommended accessories.

1. Do not operate the machine:
   • Unless trained and authorized.
   • Inflammable or explosive areas.
   • With a damaged cord or plug
   • If not in proper operating condition.
   • Unless you have read and understood the operator’s manual.
   • With the use of extension cords.
   • In outdoor areas and standing water.
2. Before operating the machine:
   • Make sure all safety devices are in place and operating properly.
3. When using a machine:
   • Do not run the machine over the cord.
   • Do not pull the cord around sharp edges or corners.
   • Do not handle the plug with wet hands.
   • Report machine damage or fault operation immediately.
   • Do not pull the machine by a cord or plug.
   • Do not unplug by pulling on the cord.
   • Do not stretch the cord.
   • Keep the cord away from heated surfaces.
4. Before leaving or servicing the machine:
   • Turn off the machine.
   • Unplug the cord from the outlet.
5. When servicing machine:
   • Unplug the cord from the outlet.
   • Use manufacturer-supplied or approved replacement parts.

WARNING:
To avoid electrical shock, please replace the power cord immediately if any damage is detected. The replacement must be performed only by an authorized person or by our customer service centre.

WARNING:
Flammable materials can cause explosions or fire. Do not use flammable materials in tanks or pick them up.

MACHINE COMPONENTS

1. Brush cover
2. Brush
3. Cover tank
4. Recovery tank
5. Solution tank
6. 8″ wheels
7. Squeegee
8. Control box
9. Trigger
10. Adjusting handle
11. Water filter
12. Ball valve
13. Squeegee lifting handle
14. Power cord hook
15. Brush/pad driving hub
16. Brush plunger
17. Plug of water filling port
18. Knob
19. Clear tube
20. Switch for brush motor
21. Switch for vacuum motor
22. *. Battery Monitor
23. Circuit breaker
24. *. Charger power cord
    • 24**. Power cord
25. Adjustable wheel

MACHINE SET-UP & INSTALLATION

UNPACK MACHINE:
Be sure and check the packing carton for any damage. Immediately report any damage to the carrier. Be careful not to let the machine vibrate while carrying, Check the contents of the package to ensure that the following items are included: Machine, squeegee assembly, brush/pad driver, and charger cord.

MACHINE SET UP & PRE-OPERATION CHECKS:

1. Sweep the outside of the machine.
2. Check the battery meter to make sure the batteries are fully charged (see battery charging, only for i18B ).
3. Check that the squeegee and brush/pad is properly installed.
4. The forward speed of the machine can be controlled by turning the handle(10). Turn the handle clockwise to speed up the machine. or turn the handle anticlockwise to slow down the machine.
5. Make sure the working surface can support the machine’s weight, and the gradient of the floor can’t exceed the limit that the machine allowed(2%).

INSTALLING PAD DRIVER OR BRUSH:

1. Turn off the machine.
2. Tilt the machine backwards, line up the driving hub with the hole of the brush or pad driver, and make sure the three blocks are fitted into the three slots of the drive hub.

• If a pad driver is being used, the appropriate pad should be attached to the pad driver first. 3. Pushtheplungerwhichon the brush cover to prevent the driving hub from rotating, then spin the brush/pad clockwise with your other hand till the clip clamps the block on the brush/pad.

INSTALLING THE SQUEEGEE:

1. Loosen the twoknobs(18) on the squeegee and slide the squeegee into the slots at the rear of the squeegee bracket. (the wheels on the squeegee point to the machine.)
2. Tighten the knobs securely.

FILLING THE SOLUTION TANK:

1. The fill port is located at the rear of the machine, pull the plug out of the hole.
2. Fill the solution tank with water. (use a hose that links to a water faucet, water temperature should not exceed 50° C) The clear tube(19) in the back right of the machine has gallon markers to help determine the water level in the solution tank(5).

Depending on the dirty level of the ground, add the proper amount of detergent into the solution tank.

WARNING:
Do not put any flammable materials into the solution tank. This can cause an explosion or a fire. Only use recommended cleaning chemicals. Contact your janitorial supply distributor for recommendations on proper chemicals.

MACHINE OPERATION

WARNING:
Do not operate the machine unless you have read and understand this manual.

1. Lower the squeegee assembly to the floor by spinning the squeegee lifting handle(13).
2. Turn the brush motor switch(20) to the “on” position.
3. Turn the vacuum motor switch(21) to the “on” position.
4. Rotate the ball valve(12) handle to a vertical position. The solution will not begin to flow until the operating triggers (9) are pulled.
5. To begin scrubbing, pull on the blue operating trigger(9), when this trigger is pulled, the pad driver will begin to spin and the solution will begin to flow.
6. Begin scrubbing by moving the machine forward.
7. Adjust solution flow by adjusting the position of the ball valve knob.

WARNING:
Do not keep the machine in the same position with the pad/brush spinning, or you might damage the floor.

WHILE OPERA TING MACHINE

1. Occasionally open the cover tank(3) to see if there is any foam build-up. If excessive foam is found, add a defoamer to the recovery tank.
   WARNING: Foam must not enter the float shut-off screen, or damage can occur to the vacuum motor. Foam will not activate the machine’s float shut-off device.

2. Occasionally view the clear tube at the back left of the machine to check the amount of cleaning solution that is left in the machine. If the squeegee assembly leaves streaks on the floor, raise the squeegee off the floor and wipe the blades down with a damp cloth.

WARNING:
Do not use your fingers to wipe or remove debris from the blades, as injury may occur.

When the solution tank runs empty, turn off the brush switch and ball valve of the solution tank. Keep the squeegee down and continue to vacuum until all the dirty water is picked up.

T ANK DRAINING

1. Turn the switches on the control panel to the “off ” position.
2. Raise the squeegee, and transport the machine to the approved area for draining tank(s).

WARNING:
Any time scrubbing is completed, or when refilling the solution tank, the recovery tank should be drained and cleaned.

WARNING:
If the recovery tank is not drained when the solution tank has been refilled, foam or water may enter the float shut-off mechanism and cause damage to the vacuum motor.

DRAINING THE RECOVERY (DIRTY) TANK

1. Remove the drain hose from the holder, and place the drain hose over the floor drain. Twist off the drain hose plug to begin the draining process.
2. Clean the recovery tank after every use. Use a fresh water hose to rinse out the recovery tank. Be careful not to spray water into the float shut-off mechanism.

WARNING:
If you are storing the machine for any period, keep the cover tank open so the tank can dry completely and smell fresh.

DRAINING THE SOLUTION (CLEAN) TANK

WARNING:
Any time the scrubbing operation is completed, the solution tank should be drained and cleaned.

1. Pull down the clear tube (back left of the machine) to remove it from the hose bar. This will allow the solution to flow freely into a bucket or floor drain.
2. Rinse the solution tank with clean water after every use. This will help prevent chemical buildup and clogging of the solution lines.
3. Once the tank is rinsed, flushed and drained, reconnect the clear tube to the hose barb. Be sure the tube is pushed all the way up on the hose barb.
4. Screw off the cover of the water filter(11) to completely exhaust the tank and check the filter screen, clean it up if necessary.
5. Screw up the cover of the water filter(11), be sure to install the screen and the “O” ring in the correct position.

BATTERY CHARGING (ONLY FOR i18B)
Each machine was equipped with an onboard charger and batteries, please use original parts only.

WARNNING:
Fire or explosion hazard. Batteries may emit hydrogen gas. Keep sparks and open flame away. Keep the battery compartment open when charging.

NOTE:
Use only approved chargers with the following specifications:

• Automatic shut-off circuit.
• Deep cycle charging.
• Output current of 8-15 Amps.
• Output voltage of 24 volts.

Battery Indicator Description:

• Green lights on  full power.
• Yellow lights on, green lights off: medium power.
• The red light is on, other lights are off at 20% power, the machine should be stopped and the batteries should be recharged.
• Red light flash: the batteries have already been discharged deeply.

NOTE:
Frequently deep discharging will reduce the life of the batteries, charge the batteries when the red light is on.

1. Place the machine in a well-ventilated area.
2. Turn the machine off.
3. If charging wet (lead acid) batteries, check the fluid level before charging.
4. Connect the charger’s AC power supply cord to a properly grounded receptacle.
5. The charger will automatically begin to charge and will automatically shut off once the batteries are fully charged.
6. Upon completion of charging, disconnect the AC power supply cord.

NOTE:
The charging status can be seen through the lights behind the transparent panel:

• Yellow light on  Normal charging
• Green light flash: 80% charged
• Green light on: Fully charged, batteries ready for use.
• Yellow lights flash  No batteries or incorrect wiring.

PREVENTATIVE MAINTENANCE

• WARNNING: Before performing any maintenance on the machine, be sure that the power is turned off, or the batteries are disconnected!
• WARNNING: Repairs are to be completed by authorized service centers only. Any repairs completed by unauthorized persons will avoid the warranty.

DAILY MAINTENANCE

1. Remove the pad driver/brush and clean it with an approved cleaner.
2. Drain recovery and solution tanks completely and rinse out with clean water. Visually check the recovery tank for debris and clean out as necessary.
3. Raise the squeegee assembly off the floor and wipe it down with a damp towel. Be sure to store the squeegee in the up position.
4. Remove the float shut-off assembly and rinse it out with clean water.
5. Clean the machine with an approved cleaner and a damp towel. Don’t spray water to clean the outside of the machine to avoid damage to the motor and wiring.
6. Unplug the vacuum motor from the power source and hose cuff & remove the drain hose from the holder before moving the recovery tank when performing maintenance.
7. Check the condition of the squeegee blade wipe edge e, rotate and replace it if worn.

MONTHLY MAINTENANCE

1. Clean the battery tops to prevent corrosion (only for i18B).
2. Check for loose battery cable connections (only for i18B).
3. Inspect and clean the recovery tank cover seal. Replace it if damaged.
4. Lubricate all grease points and pivot points with silicon spray and approved grease.
5. Check the machine for loose nuts and bolts.
6. Check the machine for leaks.

MOTOR MAINTENANCE

1. Contact your local ICE Distributor for any motor maintenance.
2. Check the motor brushes every 250 hours, Replace the brushes when they are worn to a length of 10mm or less.

BATTERY MAINTENANCE (ONLY FOR i18B)

WARNNING:
Batteries may emit hydrogen gas and an explosion or fire can result. Keep sparks and fire away from batteries at all times.

WARNNING:
Whenever servicing batteries, be sure to wear protective gloves. Avoid contact with battery acid at all times.

Note:
For the best machine performance, keep batteries charged at all times. Do not let them sit in a discharged condition.

1. Always follow the battery charging direction as outlined in the BATTERY CHARGING section of this manual.
2. Keep battery tops and terminals free from corrosion. A strong solution of baking soda and water is the best way to keep the batteries corrosion-free. DO NOT ALLOW THE BAKING SODA / WATER SOLUTION TO ENTER THE BATTERY CELLS.
3. Use a wire brush with the baking soda solution to properly clean the battery posts and connections.
4. Check battery connections for wear and loose terminals. Replace them if necessary.

MACHINE STORAGE

1. Always store the machine indoors and in its upright position.
2. Always store the machine in a dry area.
3. Always take off the pad driver/brush before storage.
4. Always store the machine with the squeegee assembly raised off the floor.
5. If storing in an area that may reach freezing temperatures, be sure to drain all fluids from the machine before storage(including the filter). Any damage caused by freezing temperatures will not be covered by the warranty.
6. Drain the recovery tank and keep the cover tank open so that it can “breathe” during storage.
7. Drain the solution tank of all fluid.

BASIC TROUBLESHOOTING

PROBLEM

| CAUSE|

SOLUTION

---|---|---

No Power

| The wiring not connected correctly or bad wiring| Check the wiring or contact the ICE Distributor
Bad brush motor| Contact ICE Distributor
Carbon brushes are worn out| Contact ICE Distributor

The vacuum motor does not run

| The wiring not connected correctly or bad wiring| Check the wiring or contact the ICE Distributor
Bad vacuum motor| Contact ICE Distributor
Carbon brushes are worn out| Contact ICE Distributor

Little or no

solution flow

| Bad ball valve| Contact ICE Distributor
Bad solution valve| Contact ICE Distributor
The ball valve position needs adjustment| When a ball valve is in a horizontal position, the amount

of solution flow is maximum.

Poor water pick-up

| Squeegee clogged| Clean debris off the squeegee with a damp towel
Squeegee blades worn| Install new squeegee blades
The squeegee was not mounted correctly| Confirm that the squeegee assembly is securely fastened to the machine and not loose fitting.
Vacuum hoses have a hole or are loose| Check hose connections and make sure they are

firm. Replace the hose if damaged.

Vacuum hose may be clogged| Check the hose for debris and remove any clog.
The drain hose stopper is loose| Tighten the drain plug.
Vacuum motor is loose| Tighten the vac motor mounting screws. Do not over- tighten or damage will occur.
The cover tank is loose| Confirm the cover tank is securely in its place.
The recovery tank is full| Drain recovery tank
Float shut-off is clogged| Remove float shut off from inside recovery tank and

remove any debris

short runtime*

| Low battery charge| Fully recharge batteries
Defective batteries| Replace batteries
Batteries need maintenance| See BATTERY MAINTENANCE
Faulty battery charger| Repair or replace battery charger

TECHNICAL SPECIFICATION

ITEM

| i18B|

i18C

---|---|---
Working Width| 18in / 450mm
Squeegee Width| 30in / 762mm
Productivity rate| 16145 ft2h / 1500m2h| 12915 ft2h / 1200m2h
Brush Dia.| 18in / 450mm
Brush Speed| 180rpm
Max Pad Pressure| 55lbs / 25kg
Voltage| 24VDC| 120VAC
Brush Motor| 0.75hp / 550W
Vacuum Motor| 0.7hp / 500W
Batteries| 2-12V, 85AH @20hr| N/A
Solution Tank Capacity| 9.25Gal / 35L
Recovery Tank Capacity| 10.57Gal / 40L
Machine Weight (w/o batteries)| 138lbs / 62.5kg
Batteries Weight| 110lbs / 50kg| N/A
Machine Length| 45.87in / 1165mm
Machine Height| 40.35 in / 1025mm
Machine Width| 20.5in / 520mm
Power cord Length| N/A| 82ft / 25m
Charger cord length| 8.2ft / 2.5m| 8.2ft / 2.5m
Max Gradient| 2%
Type of Drive| Brush assisted
Noise Level| 70 dB
WATER LIFT – AIRFLOW| 45 IN.H2O

PARTS LIST

RECOVERY TANK GROUP

DIA NO.| PART NUMBER| DESCRIPTION| SERIAL NUMBER| NO. REQ’D
---|---|---|---|---

1

| 8011001| RECOVERY TANK| 60003100364~60003100853

50010100124~50010100713

| 1
8016001| RECOVERY TANK| 60003100945~60012103001~

50010100714~51010101228~

| 1
2| 8011011| DECAL, LEFT|  | 1
3| 4010316| ICE LOGO|  | 3

4

| 8131030| DRAIN HOSE| 60003100958~60012102302

50010100724~51010101128

| 1
8131031| DRAIN HOSE| 60012102343~

51010101129~

| 1
5| 1962050| HOSE CLAMP 27-51mm|  | 2

6

| 8011006| VACUUM HOSE| 60003100945~60012102405

50010100713~51010101150

| 1
8011060| VACUUM HOSE| 60012102457~

50010100713~51010101150~

| 1

7

| 8132006| CARBON BRUSH (FRO i18B)|  | 2
8112008| CARBON BRUSH (FRO i18B)|  | 2
8011022| CARBON BRUSH (FRO i18C)|  | 2
8| 1113608| SELF-LOCKING NUT M6|  | 3
9| 1411612| PLAIN WASHER φ6×φ12×1.6|  | 5
10| 8011007| MUFFLER|  | 1

11

| 8132050| VACUUM MOTOR 24V, KIT (FRO i18B)| 60003100101~60003100364| 1
8112100| VACUUM MOTOR 24V, KIT (FRO i18B)| 60003100365~60012103001~| 1
8011200| VACUUM MOTOR 110V, 500W, KIT (FRO i18C)| 50010100124~51010101228~| 1
12| 8112005| GASKET|  | 1
13| 8112006| BOLT|  | 3
14| 1111605| HEX NUT M6|  | 3
15| 1021616| HEX HEAD BOLT M6×16|  | 10
16| 1421618| PLAIN WASHER φ6×φ18×1.6|  | 10
17| 8111300| HINGE ASSEMBLY|  | 2
18| 8011012| DECAL, RIGHT|  | 1
19| 8011009| PLATE|  | 2
20| 1421409| PLAIN WASHER 4×9×0.8,SS|  | 5
21| 1221410| PH SCREW M4×10,SS|  | 2
22| 8111015| FLOAT CAGE|  | 1
23| 8111014| FILTER COUPLING|  | 1
24| 8111001| GASKET|  | 1
25| 1321110| AUTO TAPPING SCREW ST3.5×10|  | 1
26| 1421412| PLAIN WASHER φ6×φ12×1.6|  | 1

27

| 8131003| CAP| 60003100364~60012102611

50010100713~51010101150

| 1
8131004| CAP| 60012102612~

51010101151~

| 1
28| 8011013| CABLE|  | 1

Note:

• NO 1、4、7、11：Supplier change, code update.
• NO 27：The results are optimized and will also fit older machines.

COVER TANK ASSEMBLY

DIA NO.| PART NUMBER| DESCRIPTION| SERIAL NUMBER| NO. REQ’D
---|---|---|---|---
1| 8012005| COVER TANK|  | 1

2

| 8012001| WARNING LABEL| 50010000124~50010100713| 1
8111022| WARNING LABEL (FOR i18B)| 60003000364~60012103001~| 1
8012003| WARNING LABEL (FOR i18C)| 51010101150~| 1
3| 8011005| CAP|  | 1

4

| 8012002| GASKET|  | 1
8012002A| GASKET| 60003100471~60012103001~

50010100557~51010101228~

| 1

Note:
DIA NO 4: Supplier change, code update.

SOLUTION TANK GROUP

DIA NO.

| PART NUMBER| DESCRIPTION| SERIAL NUMBER|

NO. REQ’D

---|---|---|---|---
1| 8013008| DECAL, LEFT|  | 1
2| 8050475| CABLE ASSEMBLY WITH CONNECTOR(BLACK i18B)|  | 1
 | 8050475-1| CONNECTOR, BATTERY, BLACK ANDERSON 5916G4(i18B)|  | 1

3

| 8013001| SOLUTION TANK| 60003000364~60003000853

50010000124~50010000713

| 1
8017001| SOLUTION TANK| 60003100945~60012103001~

50010100713~51010101228~

| 1
8133033| SOLUTION TANK(I18B,I18C REPLACE THE OLD WATER TANK 8013001)|  | 1
4| 8013010| 12V BATTERY (FOR i18B)|  | 2
5| 1321110| AUTO TAPPING SCREW ST3.5×10|  | 1
6| 1421409| PLAIN WASHER φ4×φ9×0.8|  | 1
7| 8133002| PLUG|  | 1
8| 8013005| TRANSPARENT HOSE|  | 1
9| 8034012| BRACKET, CASTER|  | 1
10| 8013016| 2″ CASTOR|  | 1
11| 1421618| PLAIN WASHER φ6×φ18×1.6|  | 3
12| 1422616| SPRING WASHER 6 SS|  | 3
13| 1021616| HEX HEAD SCREW M6×16, SS|  | 3
14| 1021830| HEX HEAD SCREW M8×30, SS|  | 1
15| 1422821| SPRING WASHER 8|  | 3
16| 1421824| PLAIN WASHER φ8×φ24×2.0|  | 1
17| 8016010| WHEEL SHAFT|  | 1
18| 1421816| PLAIN WASHER φ8×φ16×1.6|  | 2
19| 1021820| HEX HEAD SCREW M8×20, SS|  | 4

20

| 8115200| 8″ WHEEL|  | 2
1612607| BALL BEARING, 6004LU|  | 4
21| 1421828| PLAIN WASHER φ8×φ28×3|  | 2
22| 8115203| WHEEL CAP|  | 2
23| 1962032| HOSE CLAMP|  | 1
24| 8013009| DECAL, RIGHT|  | 1
25| 8013002| BASKET|  | 1
26| 1221510| PH SCREW M5×10,SS|  | 4
27| 1421510| PLAIN WASHER φ5×φ10×1,SS|  | 4
28| 8113009| WIRE CLAMP|  | 4
29| 8114751| WIRING BOOT (FOR i18B)|  | 4
30| 8050476| CABLE ASSEMBLY WITH CONNECTOR(RED i18B)|  | 1
 | 8050476-1| CONNECTOR, BATTERY, RED ANDERSON 5916G7(i18B)|  | 1
31| 8114750| BATTERY CABLE(I18B)|  | 1

Note:
DIA NO 3: The results are optimized and will also fit older machines.

CONTROL BOX ASSEMBLY (FOR i18B)

CONTROL CONSOLE GROUP

DIA NO.| PART NUMBER| DESCRIPTION| SERIAL NUMBER| NO. REQ’D
---|---|---|---|---
1| 8014062| REAR PANEL|  | 1
2| 1421512| PLAIN WASHRE φ5×φ12×1.5|  | 9
3| 1211516| PH SCREW M5×16|  | 5
4| 1421409| PLAIN WASHER φ4×φ9×0.8|  | 13
5| 8114707| RELAY|  | 1
6| 1113305| SELFLOCKING NUT M3|  | 8
7| 8014061| SWITCH BRACKET|  | 1
8| 1411309| PLAIN WASHER φ3×φ9×0.8|  | 8
9| 8014034| BRCKET|  | 1
10| 1411824| PLAIN WASHER φ8×φ24×2|  | 6
11| 1021820| HEX HEAD BOLT M8×20|  | 6
12| 8114030| FIXING BRACKET,CONTROL BOX|  | 1
13| 8014076| BATTERY CHARGER 24V|  | 1
14| 8113104| HANDLE|  | 1

15

| 6210111| HOSE CLAMP| 60003000364~60003000534

50010000430~50010100924

| 1
6210120| HOSE CLAMP| 60003101551~60012103001~

50010100943~51010101228~

| 1
16| 1221416| PH SCREW M4×16 SS|  | 2
17| 8014010| SQUEEGEE LIFTING HANDLE|  | 1
18| 8014008| CONTROL BOX|  | 1
19| 8034010| SQUEEGEE LIFTING ROPE|  | 1
20| 8114511| JOINT BEARING SQ6|  | 1
21| 1421618| PLAIN WASHER φ6×φ18×1.6,SS|  | 4
22| 1121605| HEX NUT M6|  | 2
23| 1421828| PLAIN WASHER φ8×φ28×3|  | 2
24| 1021830| HEX HEAD BOLT M8×30|  | 2
25| 1221512| PH SCREW M5×12,SS|  | 1
26| 8114005| PIPE COUPLING|  | 1
27| 8112030| CHARGER CORD (FOR US)|  | 1
28| 8014038| GASKET|  | 1
29| 8014036| PANEL|  | 1
30| 8014044| PLATE|  | 1
31| 1221516| PH SCREW M5×16 SS|  | 2
32| 1123608| SELFLOCKING NUT M6,SS|  | 1
33| 8114703| OVERLOAD PROTECTOR 35A|  | 1
34| 1421518| PLAIN WASHER 5×18×2|  | 1
35| 1021512| HEX HEAD BOLT M5×12,SS|  | 1
36| 8034011| BAFFLE|  | 1
37| 8014101| LIFTING ROPE SPACER|  | 1
38| 1021630| HEX HEAD BOLT M5×12,SS|  | 1
39| 8014045| TRANSPARENT PLATE|  | 1
40| 8014006| WATERPROOF SWITCH 250V 16A|  | 2
41| 8014043| WIRE BUFFER|  | 1
42| 8014041| WIRE CLAMP|  | 1
43| 1221616| PH SCREW M6×16,SS|  | 1
44| 2320403| STRAIN RELIEF|  | 1
---|---|---|---|---
45| 8014063| BATTERY CAPACITY INDICATOR|  | 1
46| 1221410| PH SCREW M4×10,SS|  | 15
47| 8014067| PANEL DECAL|  | 1
48| 8014069| FRONT PANEL|  | 1
49| 8114101| SHAFT|  | 1
50| 8014004| GASKET|  | 1
51| 1221412| PH SCREW M4×12, SS|  | 4
52| 1432411| SPRING WASHER 4|  | 2
53| 1411409| PLAIN WASHER φ4×φ9×0.8|  | 2
54| 8014022| CONTROL TRIGGER|  | 1
55| 8014033| PLATE|  | 1
56| 1534608| SET SCREW M6×8|  | 4
57| 8014031| HEX BUSHING|  | 1
58| 8014032| SPRING ROD|  | 1
59| 8014035| SPRING|  | 1
60| 1211320| PH SCREW M3×20|  | 2
61| 1434300| WASHER WITH TOOTH 3|  | 2
62| 8114712| MICROSWITCH|  | 1
63| 1113507| SELFLOCKING NUT M5|  | 7
64| 8210421| RELAY 24VDC 30A|  | 1
65| 1123406| SELFLOCKING NUT M4, SS|  | 2

Note:
DIA NO 15、19:Supplier change, code update.

CONTROL BOX ASSEMBLY (FOR i18C)

DIA NO.| PART NUMBER| DESCRIPTION| SERIAL NUMBER| NO. REQ’D
---|---|---|---|---
1| 1421409| PLAIN WASHER φ4×φ9×0.8|  | 11
2| 1211516| PH SCREW M5×16|  | 4
3| 1113305| SELF-LOCKING NUT M3|  | 2
4| 1021820| HEX HEAD BOLT M8×20|  | 6
5| 1411824| PLAIN WASHER φ8×φ24×2|  | 6
6| 1113507| SELF-LOCKING NUT M5|  | 4
7| 8114030| FIXING BRACKET, CONTROL BOX|  | 1
8| 8113104| HANDLE|  | 1

9

| 6210111| HOSE CLAMP| 60003000364~60003000534

50010000430~50010100924

| 1
6210120| HOSE CLAMP| 60003101551~60012103001~

50010100943~51010101228~

| 1
10| 1221416| PH SCREW M4×16 SS|  | 2
11| 8014010| SQUEEGEE LIFTING HANDLE|  | 1
12| 8014008| CONTROL BOX|  | 1
13| 8014013| SQUEEGEE LIFTING ROPE|  | 1
8034010| SQUEEGEE LIFTING ROPE|  | 1
14| 8114511| JOINT BEARING SQ6|  | 1
15| 1421618| PLAIN WASHER φ6×φ18×1.6,SS|  | 4
16| 1121605| HEX NUT M6|  | 2
17| 1421828| PLAIN WASHER φ8×φ28×3|  | 2
18| 1021830| HEX HEAD BOLT M8×30|  | 2
19| 1221512| PH SCREW M5×12|  | 1
20| 1221516| PH SCREW M5×16 SS|  | 2
21| 8014044| PLATE|  | 1
22| 8114005| PIPE COUPLING|  | 1
23| 8014037| PANEL, BOTTOM|  | 1
24| 8014038| GASKET|  | 1
25| 8014068| OVERLOAD PROTECTOR 10A|  | 1
26| 8014053| POWER CORD|  | 1
27| 1221410| PH SCREW M4×10,SS|  | 15
28| 1123608| SELF-LOCKING NUT M6, SS|  | 1
29| 8034011| BAFFLE|  | 1
30| 1421512| PLAIN WASHRE φ5×φ12×1.5|  | 8
31| 1021512| HEX HEAD BOLT M5×12, SS|  | 1
32| 8014101| LIFTING ROPE SPACER|  | 1
33| 1021630| HEX HEAD BOLT M6×30, SS|  | 1
34| 8014006| WATERPROOF SWITCH 250V 16A|  | 2
35| 8014041| WIRE CLAMP|  | 1
36| 8014043| WIRE BUFFER|  | 1
37| 1221614| PH SCREW M6×14|  | 1
38| 1422616| SPRING WASHER 6|  | 1
39| 2320403| STRAIN RELIEF|  | 1
40| 8014007| PANEL DECAL|  | 1
41| 8014005| FRONT PANEL|  | 1
---|---|---|---|---
42| 8014004| GASKET|  | 1
43| 8114101| SHAFT|  | 1
44| 1221412| PH SCREW M4×12,SS|  | 2
45| 1411409| PLAIN WASHRE φ4×φ9×0.8|  | 2
46| 1432411| SPRING WASHER 4|  | 2
47| 8014033| PLATE|  | 1
48| 8014022| CONTROL TRIGGER|  | 1
49| 1534608| SET SCREW M6×8|  | 4
50| 8014031| HEX BUSHING|  | 1
51| 8014032| SPRING ROD|  | 1
52| 8014035| SPRING|  | 1
53| 1211325| PH SCREW M3×25|  | 2
54| 1411309| PLAIN WASHER φ3×φ9×0.8|  | 4
55| 8014071| SWITCH|  | 1
56| 8014061| SWITCH BRACKET|  | 1
57| 8014002| REAR PANEL|  | 1
58| 8014034| BRACKET|  | 1

Note:
DIA NO 9、13:Supplier change, code update.

SCRUB HEAD GROUP

DIA NO.| PART NUMBER| DESCRIPTION| SERIAL NUMBER| NO. REQ’D
---|---|---|---|---
1| 8015200| MOTOR 24V 550W, KIT (FOR i18B)|  | 1
8015220| MOTOR 120V 550W, KIT (FOR i18C)|  | 1
2| 8015020| ADJUSTING HANDLE|  | 1
3| 8015010| BRUSH HANGER|  | 1
4| 1511065| HEX SOCKET SCREW M10×65|  | 1
5| 1644220| PIN 12×20|  | 2
6| 8015101| DECAL|  | 1
7| 1111008| HEX NUT M10|  | 1
8| 8015104| BEARING GEC6C|  | 1
9| 8015105| BEARING HOUSING|  | 1
10| 1439005| DETENT RING 5|  | 1
11| 8015087| ASSEMBLY BOARD|  | 1
12| 8015050| BRUSH PLUNGER|  | 1
13| 1123810| SELF-LOCKING NUT M8, SS|  | 1
14| 1421816| PLAIN WASHER φ8×φ16×1.6,SS|  | 3
15| 8115404| SPACER|  | 1
16| 8116009| BUMPING WHEEL|  | 1
17| 8111023| WARNING DECAL|  | 1
18| 1221512| PH SCREW M5×12|  | 2
19| 1421510| PLAIN WASHER φ5×φ10×1,SS|  | 2
20| 8116002| WASHER|  | 1
21| 8116003| SPRING CLAMP|  | 1
22| 8116008| BRUSH HUB|  | 1
23Δ| 9050018| BRUSH 18″|  | 1
24| 1421828| PLAIN WASHER φ8×φ28×3|  | 1
25| 8015090| SPLASH GUARD|  | 1
26| 1422821| SPRING WASHER 8|  | 1
27| 1023810| HEX HEAD BOLT 5/16×1″, SS|  | 1
28| 1021835| HEX HEAD BOLT M8×35, SS|  | 1
29| 1111215| HEX NUT M16|  | 1
30| 8015108| SUPPORTER|  | 1
31| 1011016| HEX BOLT M6×16|  | 1
32| 1411020| PLAIN WASHER φ10×φ20×2|  | 4
33| 1011625| HEX HEAD BOLT M6×25|  | 4
34| 1421618| PLAIN WASHER φ6×φ18×1.6,SS|  | 8
35| 1221510| SH SCREW M5×10|  | 1
36| 1212410| SH SCREW M4×10|  | 2
37| 8015060| WATER INLET|  | 1
38| 8015041| MOTOR BRACKET|  | 1
39| 8015005| BRUSH COVER|  | 1
40| 1222510| SH SCREW M5×10|  | 2
41| 1421518| PLAIN WASHER φ5×φ18×2,SS|  | 4
42| 1422513| SPRING WASHER 5|  | 5
43| 1221515| PH SCREW M5×15|  | 3
44| 1221616| PH SCREW M6×16|  | 8
45| 8015103| VALVE BRACKET|  | 1
46| 1221410| PH SCREW M4×10,SS|  | 2
47| 1321213| AUTO TAPPING SCREW ST4.2×13|  | 2
48| 1646240| COTTER PIN 2×40|  | 2
---|---|---|---|---
49| 8015116| NYLON WASHER φ12.5×φ20×1.5|  | 4
50| 8015001| BRACKET|  | 1
51| 1123608| SELF-LOCKING NUT M6, SS|  | 4
52| 1511040| HEX SOCKET SCREW M10×40|  | 2
53| 8015007| BUSHING|  | 3
54| 1113012| SELF-LOCKING NUT M10|  | 1
55| 8015115| NYLON WASHER φ10.5×φ30×2.5|  | 2
56| 8015121| SPACER 13×10.5×5.5|  | 1
57| 8015002| BRACKET|  | 1
58| 8116004| DETENT RING|  | 1
59| 1656432| KEY 6.35×32|  | 1
60| 8015003| SPACER 25.5×19.5×5|  | 1
61| 8115004| SPRING|  | 1

23 △

DIA NO.| PART NUMBER| DESCRIPTION| SERIAL NUMBER| NO. REQ’D
---|---|---|---|---
1| 9050018| BRUSH 18″|  | 1
2| 9040017| PAD DRIVER 17″|  | 1
3| 9000001| BIG MOUTH|  | 1

SQUEEGEE HOLDER ASSEMBLY

DIA NO.| PART NUMBER| DESCRIPTION| SERIAL NUMBER| NO. REQ’D
---|---|---|---|---
1| 8037020| BRACKET, SQUEEGEE MNTG|  | 1
2| 1421618| PLAIN WASHER 6×18×1.6|  | 3
3| 1422616| SPRING WASHER 6 SS|  | 3
4| 1021616| HEX HEAD SCREW M6×16, SS|  | 3
5| 1021230| HEX HEAD BOLT M12×30, SS|  | 2
6| 1421132| PLAIN WASHER 12×32×2.0|  | 2
7| 8035001| PLASTIC WASHER 12×30×1.5|  | 4
8| 8115004| SPRING|  | 1

9

| 8115405| SLEEVE, P/M| 60003000364

50010000124~50010000518

| 2
8115005| SLEEVE, P/M| 60003000365~60012103001~

50010000519~51010101228~

| 2
10| 8037010| BRACKET, SQUEEGEE|  | 1
11| 1123115| SELF-LOCKING NUTS M12|  | 2
12| 8115001| SQUEEGEE SUPPORT|  | 1
13| 8037015| PIN 12×70|  | 1
14| 1645324| COTTER PIN|  | 1

Note:
NO 9: The results are optimized and will also fit older machines.

SOLUTION SYSTEM ASSEMBLY

DIA NO.| PART NUMBER| DESCRIPTION| SERIAL NUMBER| NO. REQ’D
---|---|---|---|---
1| 1962016| HOSE CLAMP|  | 2
2| 8018004| HOSE|  | 1
3| 8018007| SOLENOID VALVE, 24V (FOR i18B)|  | 1
8018009| SOLENOID VALVE, 110V (FOR i18C)|  | 1
4| 8018003| HOSE|  | 1
5| 8119006| HOSE CLAMP|  | 4
6| 8119200| WATER FILTER|  | 1
7| 8018002| HOSE|  | 1
8| 8013007| JOINT|  | 1
9| 8018006| BALL VALVE|  | 1
10| 8013006| 90º JOINT|  | 1
11| 8119101| FILTER BODY|  | 1
12| 1622765| O RING|  | 1
13| 8119104| FILTER SCREEN|  | 1
14| 8119102| FILTER COVER|  | 1
15| 1421409| PLAIN WASHER 4×9×0.8,SS|  | 2
16| 1221412| PH SCREW M4×12, SS|  | 2

SQUEEGEE ASSEMBLY

DIA NO.| PART NUMBER| DESCRIPTION| SERIAL NUMBER| NO. REQ’D
---|---|---|---|---
1| 1123810| LOCK NUT M8|  | 2
2| 1421824| FLAT WASHER M8× ∮ 24×2.0|  | 4
3| 8116009| PROTECTIVE WHEEL|  | 2
4| 1021616| HEX BOLT M6×16|  | 2
5| 8115404| BEARING, JOURNAL|  | 2
6| 1421612| FLAT WASHER M6× ∮ 12×1.6|  | 2
7| 8118300| LEFT BRACKET|  | 1
8| 8118400| CASTER, 2 INCH|  | 2
9| 8118600| CLAMP ASSEMBLY, SQUEEGEE|  | 1

10

| 8118022| SQUEEGEE BLADE, REAR, LINATEX|  | 1
8118002| SQUEEGEE BLADE, REAR, PU (OPTION)|  | 1
11| 8118003| STAR KNOB M8|  | 4
12| 8118004| SQUEEGEE HOUSING|  | 1
13| 1021835| HEX BOLT M8×35|  | 2
14| 8118009| RETAINER, SQUEEGEE|  | 1
15| 8118008| SPACER|  | 1
16| 1222515| SCREW M5×15|  | 6
17| 8118010| RETAINER ASSEMBLY|  | 1

18

| 8118021| SQUEEGEE BLADE, FRONT, LINATEX|  | 1
8118001| SQUEEGEE BLADE, FRONT, PU (OPTION)|  | 1
19| 8118610| SHORT CLAMP ASSEMBLY|  | 1
20| 1221575| SCREW M5×75|  | 1
21| 8118200| RIGHT BRACKET|  | 1
22| 1121008| HEX NUT M10|  | 2
23| 8118600A| CLAMP ASSEMBLY|  | 1
24| 8118624| SHAFT|  | 1
25| 8118623| SPACER|  | 1
26| 1123507| LOCK NUT M5|  | 1

27

| 8011003| VACUUM HOSE|  | 1
8011060| VACUUM HOSE|  | 1

28

| 8118000| SQUEEGEE ASSEMBLY, LINATEX|  | 1
8118000-PU| SQUEEGEE ASSEMBLY, PU|  | 1

Note:
DIA NO 27:Supplier change, code update.

WEAR & TEAR PARTS LIST

DIA NO.

| PART NUMBER| DESCRIPTION| SERIAL NUMBER|

NO. REQ’D

---|---|---|---|---
1| 8115200| WHEEL, 8 INCH, WITH BEARINGS|  | 2
2| 8116009| BUMPER, ROLLER|  | 3
3| 8118022| REAR SQUEEGEE BLADE, LINATEX|  | 1
4| 8118021| FRONT SQUEEGEE BLADE, LINATEX|  | 1
5| 9040017| PAD HOLDER, 17 INCH|  | 1
6| 9050018| BRUSH, 18 INCH|  | 1

WIRING DIAGRAM

WIRING DIAGRAM(i18B)

• BAT: 2-12V battery
• CHR: Onboard charger
• SW: Control handle switch
• SW1: Brush motor switch
• SW2: Vacuum motor switch
• ES1: Brush motor solenoid switch
• ES2: Vacuum motor relay
• BCI: Battery capacity indicator
• BR: Circuit breaker
• EW: Solution solenoid valve
• M1: Brush motor
• M2: Vacuum motor

WIRING DIAGRAM(i18C)

CERTIFICATE OF QUALIFIED

• MODEL:
• INSPECTOR:
• SERIAL NO.:
• DATE:

ICE Cobotics (GuangDdong) Company Limited

• TEL: (+86) 769 8186 9000
• FAX: (+86) 769 8186 3000

References

• Intelligent Cleaning Equipment (ICE)

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>