KLARK TEKNIK DN32-ADAT Expansion Module User Guide
- June 17, 2024
- Klark Teknik
Table of Contents
KLARK TEKNIK DN32-ADAT Expansion Module User Guide
Important Safety Instructions
Terminals marked with this symbol carry electrical current of suffi cient magnitude to constitute risk of electric shock. Use only high-quality professional speaker cables with ¼” TS or twist-locking plugs pre-installed. All other installation or modifi cation should be performed only by qualifi ed personnel.
This symbol, wherever it appears, alerts you to the presence of uninsulated dangerous voltage inside the enclosure – voltage that may be suffi cient to constitute a risk of shock.
This symbol, wherever it appears, alerts you to important operating and maintenance instructions in the accompanying literature. Please read the manual.
Caution
To reduce the risk of electric shock, do not remove the top cover (or the rear section). No user serviceable parts inside. Refer servicing to qualifi ed personnel.
Caution
To reduce the risk of fi re or electric shock, do not expose this appliance to rain and moisture. The apparatus shall not be exposed to dripping or splashing liquids and no objects fi lled with liquids, such as vases, shall be placed on the apparatus.
Caution
These service instructions are for use by qualified service personnel only. To reduce the risk of electric shock do not perform any servicing other than that contained in the operation instructions. Repairs have to be performed by qualified service personnel.
- Read these instructions.
- Keep these instructions.
- Heed all warnings.
- Follow all instructions.
- Do not use this apparatus near water.
- Clean only with dry cloth.
- Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
- Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifi ers) that produce heat.
- Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding-type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fi t into your outlet, consult an electrician for replacement of the obsolete outlet.
- Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.
- Use only attachments/accessories specifi ed by the manufacturer.
- Use only with the cart, stand, tripod, bracket, or table specifi ed by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/ apparatus combination to avoid injury from tip-over.
- Unplug this apparatus during lightning storms or when unused for long periods of time.
- Refer all servicing to qualifi ed service personnel. Servicing is required when the apparatus has been damaged in any way, such as power supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does notoperate normally, or has been dropped.
- The apparatus shall be connected to a MAINS socket outlet with a protective earthing connection.
- Where the MAINS plug or an appliance coupler is used as the disconnect device, the disconnect device shall remain readily operable.
- Correct disposal of this product: This symbol indicates that this product must not be disposed of with household waste, according to the WEEE Directive (2012/19/EU) and your national law. This product should be taken to a collection center licensed forthe recycling of waste electrical and electronic equipment (EEE).
The mishandling of this type of waste could have a possible negative impact on the environment and human health due to potentially hazardous substances that are generally associated with EEE. At the same time, your cooperation in the correct disposal of this product will contribute to the effi cient use of natural resources. For more information about where you can take your waste equipment for recycling, please contact your local city offi ce, or your household waste collection service.
Warning
Failure to observe the following warnings may lead to fatality or serious injury from fi re or electric shock.
Before installing the card, you must refer to the owner’s manual of the host device or to klarkteknik.com to verify that your host device supports this card, and to verify the number of cards that can be installed in combination with other MIDAS or third-party cards.
-
Do not attempt to disassemble or modify the card.
Do not apply excessive force to board connectors or other board components. Mishandling of board may lead to shock, fi re hazard, or equipment failure. -
Disconnect the power cable from the main unit before installing this card to eliminate shock hazard.
Caution
Failure to observe the following precautions may lead to personal injury, or may result in damage to equipment or other property.
- Do not touch the board’s metallic leads (pins) when handling the card. Pins are sharp and may cause injury.
- The card is electrostatic-sensitive. Before handling the card, you should briefl y touch the main unit’s metal casing with your bare hand so as to drain off any static charge from your body. MUSIC GROUP assumes no responsibility for data loss, equipment damage, or injury caused by inappropriate handling or usage.
Connector Plate
- Single BNC coaxial, in/output switchable, no internal termination, LED indicates WC output (Master mode)
- 4x To slink inputs and 4x To slink outputs, 8 channels per connector
- 2x small handles for removing the expansion card from the slot
- 2x M3x6 screws left and right for fastening the card in the slot
- 2x small counter sunk screws below the handles and 8 screws above the connectors. Do not loosen these!
Connection Scenarios
DN32-ADAT ➝ external hard disc recorder (providing Word Clock via BNC coaxial
connection)
2x XL48 -> MIDAS M32
DN32-ADAT ➝ external automixer ➝ return to DN32-ADAT
- Out 1-8 and 9-16 to Auto-mixing Processor inputs
- In 1-8 and 9-16 from Auto-mixing Processor outputs
- Routing/home > Input 1-16 = Card In 1-16, Routing/card out > Output 1-16 = Local 1-16
Note, this would also apply for any other sort of specialized outboard
processing that features ADAT I/O. It can be used for all 32 x 32 channels
simultaneously, even spread over several external processors.
Mixer Setup
Specifications
TOSLINK opt. IN: 4
TOSLINK opt. OUT: 4
WORDCLOCK BNC IN/OUT: 1
Input/Output Characteristics
Sample rates: 44.1 kHz / 48 kHz
Sample word length: 24 Bit
Clock synchronisation selectable: internal/Local WordClock In
ADAT In 1
ADAT In 2
ADAT In 3
ADAT In 4
FEDERAL COMMUNICATIONS COMMISSION COMPLIANCE INFORMATION
DN32-ADAT
This equipment complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a ClassB digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit diff erent from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Important information:
Changes or modifi cations to the equipment not expressly approved by MUSIC Group can void the user’s authority to use the equipment.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>