HINKLEY 28824-28820 Outdoor Wall Sconce Instruction Manual

HINKLEY 28824-28820 Outdoor Wall Sconce

Product Information

Specifications

• Brand: HINKLEY
• Product Type: Outdoor Wall Sconce
• Item No: 28824-28820
• Bulb Type: Medium Base (D)

Product Usage Instructions

Mounting Instructions

1. Find a clear area in which you can work.
2. Unpack the fixture and glass from the carton.
3. Carefully review the instructions before assembly.
4. To begin, remove the mounting plate (A) from the backplate (C) by removing screws (E) located on the side of the backplate – see Drawing 1.
5. Attach the mounting bracket (A) to the junction box (J) using two 8-32 screws (B) (not provided) or the screws from the previously installed mounting strap or plate. Make sure threaded holes are on the side when installing the mounting plate, and ensure the plate is plumb by placing a level across the top. Adjust the plate and tighten the screws to secure the mounting plate.
6. Make all necessary wiring connections following the instruction sheet (IS-18) provided. Read the wiring and grounding instructions (IS 18) and any additional directions. Turn off the power supply during installation. If new wiring is required, consult a qualified electrician or local authorities for code requirements.
7. After all electrical connections are made, slip the backplate (C) over the mounting strap (A) and align the holes in the side of the backplate (C) with the threaded holes on the side of the mounting strap (A).
8. Thread in the screws (E) removed earlier to secure the backplate to the mounting strap.
9. Installation is complete, and power can be restored.

Caulking Instructions (IS200)

After securing the fixture to the wall, it is recommended to seal the gap between the wall and the fixture backplate on the top and both sides using a good quality waterproof caulk or silicone sealant (not included) – see Drawing

Instructions:

1. Apply a bead of caulk to seal the gap.
2. Use a caulking gun for easy application.

FAQ

• Q: What type of bulb does the fixture use?
  A: The fixture uses a medium base bulb (D).

• Q: How should I seal the gap between the fixture backplate and the wall?
  A: It is recommended to use a good quality waterproof caulk or silicone sealant (not included). Apply a bead of caulk to seal the gap using a caulking gun for easy application.

• Q: Are the screws for attaching the mounting bracket provided?
  A: No, the screws for attaching the mounting bracket (A) to the junction box (J) are not provided. You can use two 8-32 screws from a previously installed mounting strap or plate.

Item No : 28824-28820

Mounting Instructions

start here

1. Find a clear area in which you can work.
2. Unpack fixture and glass from carton.
3. Carefully review instructions before assembly

• To begin it will be necessary to remove mounting plate (A) from backplate (C) by removing screws (E) located on the side of the backplate – see Drawing 1.
• To begin installation, first attach mounting bracket (A) to junction box (J) by using two 8-32 screws (B) not provided, or the screws from the previously installed mounting strap or plate. Make sure threaded holes are on the side when installing the mounting plate, and plate is plumb by placing a level across the top. Adjust plate and tighten the screws to secure the mounting plate.
• Next, make all wiring connections. Follow the instruction sheet (IS-18) provided.

SAFETY WARNING : READ WIRING AND GROUNDING INSTRUCTIONS (I.S. 18) AND ANY ADDITIONAL DIRECTIONS. TURN POWER SUPPLY OFF DURING INSTALLATION. IF NEW WIRING IS REQUIRED, CONSULT A QUALIFIED ELECTRICIAN OR LOCAL AUTHORITIES FOR CODE REQUIREMENTS.
Make electrical connections from supply wire to fixture lead wires. Refer to the instruction sheet (I.S. 18) and follow all instructions to make all necessary wiring connections. Then refer back to this sheet to complete the installation of this fixture

1. After all electrical connections are made. Slip backplate (C) over mounting strap (A) and align holes in the side of backplate (C) with threaded holes on the side of mounting strap (A).
2. Thread in screws (E) removed earlier to secure the backplate to the mounting strap.
3. Installation is complete and power can be restored

Note : fixture ues a medium base bulb (D)

IS200 Caulking Instructions

After securing the fixture to the wall it is recommended that the gap between the wall and the fixture backplate be sealed on the top and both sides, with a good quality waterproof caulk or silicone sealant (NOT INCLUDED) – see Drawing

• After securing the fixture in place it is recommended that the gap between the mounting top and fixture base be sealed with any good quality waterproof caulk or silicone sealant (not included). It is also recommended that a small bead of caulk or sealant be put under the ball knobs used to mount fixture – see Drawing 2.

Wiring grounding instructions

SAFETY WARNING : READ WIRING AND GROUNDING INSTRUCTIONS (IS 18) AND ANY ADDITIONAL DIRECTIONS. TURN POWER SUPPLY OFF DURING INSTALLATION. IF NEW WIRING IS REQUIRED, CONSULT A QUALIFIED ELECTRICIAN OR LOCAL AUTHORITIES FOR CODE REQUIREMENTS

Indoor Fixtures

1. Connect positive supply wire (A) (typically black or the smooth, unmarked side of the two-conductor cord) to positive fixture lead (B) with an appropriately sized twist on the connector – see Drawings 1 or 2.
2. Connect negative supply wire (C) (typically white or the ribbed, marked side of the two-conductor cord) to negative fixture lead (D).
3. Please refer to the grounding instructions below to complete all electrical connections

Outdoor Fixtures

1. Connect positive supply wire (A) (typically black or the smooth unmarked side of the two-conductor cord) to positive fixture lead (B) with an appropriately sized twist on the connector — see Drawings 2 or 3.
2. Connect negative supply wire (C) (typically white or the ribbed, marked side of the two-conductor cord) to negative fixture lead (D).
3. Cover open end of connectors with silicone sealant to form a watertight seal.
4. If installing a wall mount fixture, use caulk to seal gaps between the fixture mounting plate (backplate) and the wall. This will help prevent water from entering the outlet box. If the wall surface is lap siding, use caulk and a fixture mounting platform specially.
5. Please refer to the grounding instructions below to complete all electrical connections.

Grounding instructions

• Flush Mount Fixtures
  For positive grounding in a 3-wire electrical system, fasten the fixture ground wire (E) (typically copper or green plastic coated) to the fixture mounting strap (M) with the ground screw (S) – see Drawing 1.
  Note : On straps for screw-supported fixtures, first install the two mounting screws in the strap. Any remaining tapped hole may be used for the ground screw.

• Chain Hung Fixtures
  Loop fixture ground wire (E) (typically copper or green plastic coated) under the head of the ground screw (S) on the fixture mounting strap (M) and connect to the loose end of the fixture ground wire directly to the ground wire of the building system with appropriately sized twist-on connectors – see Drawing 2.

• Post-Mount Fixtures
  Connect fixture ground wire (E) (typically copper or green plastic coated) to the power supply ground with an appropriately sized twist-on connector inside the post. Cover the open end of the connector with silicone sealant to form a watertight seal – see Drawing 3.

HINKLEY 33000 Pin Oak Parkway, Avon Lake, OH 44012 800.446.5539 / 440.653.5500 hinkley.com

References

• HINKLEY - Lighting and Ceiling Fans

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>