HINKLEY 980030 3 Speed Fan and Light Wall Control with Receiver Instructions
- June 3, 2024
- HINKLEY
Table of Contents
3 SPEED FAN & LIGHT
WALL CONTROL WITH RECEIVER
INSTALLATION INSTRUCTIONS
Model: 980030
980030 3 Speed Fan and Light Wall Control with Receiver
READ AND SAVE THESE INSTRUCTIONS
GENERAL INFORMATION
This wall control is designed to separately control your ceiling fan speed and light brightness.
- The fan button will control the fan speed. (Hi, Medium, Low)
- The light buttons will control the lights, brightness dimmer and off.
- The red indicator on the transmitter will light when the button is pressed.
NOTE: When installing the remote control, be sure your fan control or pull chain switch are in the “HIGH SPEED” position and the light control or switch is set to “ON”.
INSTALLATION AND OPERATING INSTRUCTIONS
NOTE: This wall control unit is equipped with 16 code combinations to prevent possible interference from or to other remote units. The frequency switches on your receiver and transmitter have been preset at the factory. Please recheck to make sure the switches on transmitter and receiver are set to the same position, any combination of settings will operate the fan as long as the transmitter and receiver are set to the same position.
SETTING THE CODE
This unit has 16 different code combinations. To set the code, perform these
steps:
A. Setting the code on the transmitter:
a. Slide the code switches to your choice of up or down position.
(Factory setting is all up). Do not use this Position. Use a small screwdriver
or a ballpoint pen to slide firmly up or down (Figure A).
B. Setting the code on the receiver:
a. Slide the code switches to the same positions as set on your
transmitter (Figure B).
**INSTALLING RECEIVER IN THE CEILING FAN
**
A. Safety precautions:
WARNING: HIGH VOLTAGE! Household electrical power can cause serious
injury or death. Disconnect the source of electrical power to the ceiling fan
by removing the fuse or switching off the circuit breaker.
B. Installing receiver in fan.:
a. Remove the ceiling fan canopy from the mounting bracket.
b. Disconnect the existing wiring between the ceiling fan and supply at
the electrical junction box.
c. Lay the black antenna wire on top of the receiver, and put the
receiver in the mounting bracket. (Fig. C)
d. Make the connections as follows, using the wire nuts supplied: (Fig.
D)
| CONNECT | TO |
|---|---|
| Green fan wire | Bare supply wire |
| Black receiver wire (AC IN L) | Black supply wire |
| White receiver wire(AC IN N) | White supply wire |
| White receiver wire (TO MOTOR N) | White fan wire |
| Black receiver wire (TO MOTOR L) | Black fan wire |
| Blue receiver wire(FOR LIGHT) | Blue light wire |
If other fan or supply wires are different color, have this unit installed by
a qualified electrician.
e. Push all connected wires up into junction box.
f. Reinstall the canopy on the mounting bracket.
g. Restore the electrical power.
INSTALLING THE WALL TRANSMITTER
WARNING! HOOK UP “IN SERIES” ONLY. DO NOT CONNECT NEUTRAL SUPPLY WIRE OF
ELECTRIC CIRCUIT TO THE TRANSMITTER WALL SWITCH, DAMAGE TO THE TRANSMITTER
WALL SWITCH AND POSSIBLE FIRE COULD OCCUR.
a. Remove the existing wall plate and switch from the wall outlet box.
b. Make the electrical connections as shown in Fig.E. If your outlet box
has a ground wire (Green or Bare Copper) connect the Transmitter’s ground wire
directly to one of the screws from the outlet box . Secure all wire
connections with the plastic wire nuts provided.
c. Carefully tuck the wire connections inside the outlet box. Use the
screws provided to secure the wall transmitter and wall plate to the outlet
box. (Fig. F)
OPERATING TRANSMITTER:
A. Store the transmitter away from excess heat or humidity.
B. Remove the faceplate of the Wall Switch by lifting at the top and then
insert the supplied 12V battery. Duracell MN21/Eveready A23/GP 23A all 12V.
(Fig. G)
C. This remote control unit is equipped with 16 code combinations to
prevent possible interference from or to other remote units such as garage
door openers, car alarm or security system. If you find that your fan and
light kit go on and off without using your remote control, simply change the
combination code in your transmitter and receiver.
D. Operation buttons on the panel of the transmitter: (Figure H)
HI button – for fan high speed.
MED button – for fan medium speed.
LOW button – for fan low speed.
The”LIGHT” button: This Button will control the light brightness. The light
function is controlled by pressing the “LIGHT” button. Hold the button down to
increase or decrease the light. Tap the button quickly to turn the light off
or on. If you press the button in excess of 0.7 seconds it becomes a dimmer.
The light varies cyclically in 0.8 seconds. The light key has auto resume, so
it will stay at the same brightness as the last time it was turned off.
YOUR REMOTE NOW HAS FULL CONTROL OF THE FAN AND LIGHT.
TROUBLESHOOTING GUIDE
A. Fails to operate:
a. Power to the receiver?
b. Receiver wired correctly?
c. Fan manual speed control in highest position?
d. Light kit switch turned on?
e. Code set at exact same position in both transmitter and receiver?
B. Won’t operate at distance: .
If transmitter operates the fan and the light kit when up close, but not a 30
feet away, try placing the black antenna wire higher; up through the ceiling,
outside the junction box.
NOTICE!
Your ceiling fan and light kit assembly must meet the following requirements:
- Do not use with solid state fans.
- Electrical rating: 120V / 60 Hz
MAX. motor amps:1.0 A
MAX. light watts: 250 W
(Incandescent only)
For Warranty Information please visit www.hinkley.com
Documents / Resources
|
HINKLEY 980030 3 Speed Fan and Light Wall Control with
Receiver
[pdf] Instructions
980030 3 Speed Fan and Light Wall Control with Receiver, 980030, 980030 Light
Wall Control with Receiver, 3 Speed Fan and Light Wall Control with Receiver,
3 Speed Fan, Light Wall Control, Receiver
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>