HINKLEY 1141OL-CL Casa Large Post Top or Pier Mount Lantern Instruction Manual

: October 30, 2023
: HINKLEY

Table of Contents

Assembly Instructions
Post mounting Instructions PMSS-1
wiring grounding instructions
Documents / Resources

HINKLEY 1141OL-CL Casa Large Post Top or Pier Mount Lantern Instruction Manual

DRAWING 1 – MOUNTING

MOUNTING INSTRUCTIONS

Assembly Instructions

start here

Find a clear area in which you can work.
Unpack fixture and glass from carton.
Carefully review instructions prior to assembly.

NOTE : It is recommended that the luminaire body be installed on a post prior to installing the glass. To accomplish this follow instruction sheet PMSS-1 provided.

SAFETY WARNING: READ WIRING AND GROUNDING INSTRUCTIONS (I.S. 18) AND ANY ADDITIONAL DIRECTIONS. TURN POWER SUPPLY OFF DURING INSTALLATION. IF NEW WIRING IS REQUIRED, CONSULT A QUALIFIED ELECTRICIAN OR LOCAL AUTHORITIES FOR CODE REQUIREMENTS.

NOTE : Prior to installing the glass the fixture should be lamped accordingly.

To install glass, first remove loop (1) on top of the fixture, from center stem (5) – see Drawing 1.
Next remove spacer (2), and then slip roof and scroll assembly (3) off of center stem (5).
Next slide glass (4) into fixture, making sure small hole in the top of glass is at the top of the fixture.
Next slip roof and scroll assembly (3) onto center stem (5) and down onto the glass making sure to align the pins (P) in the bottom of the scrolls, with the holes in the top of the uprights (U).
Next replace spacer (2), and then thread on loop (1) to complete assembly.

Drawing 1 – Post Mounting

Post mounting Instructions PMSS-1

Find a clear area in which you can work.
Unpack fixture and glass from carton.
Carefully review instructions prior to assembly

*** The installation of this luminaire will be accomplished by first making all necessary electrical connections, mounting luminaire body to installed post, and then completing assembly.

NOTE : it is recommended that steps 1 and 2 be done prior to installation of the glass or before any assembly is done on the fixture body

To begin installation it will be necessary to drill 3 pilot holes in the installed post in order to mount the fixture body. This is accomplished by sliding the post fitter (1), of the fixture body (2), over the installed post. Using the holes (3), in the side of the post fitter, mark the mounting hole locations – see DRAWING 1.
NOTE: MAKE SURE FIXTURE BODY IS ORIENTED IN THE POSITION YOU WANT, BEFORE MARKING THE HOLE LOCATIONS.
Now remove fixture body from installed post and drill a 5/32” (4mm) dia. hole at the marked locations.

SAFETY WARNING: READ WIRING AND GROUNDING INSTRUCTIONS (I.S. 18) AND ANY ADDITIONAL DIRECTIONS. TURN POWER SUPPLY OFF DURING INSTALLATION. IF NEW WIRING IS REQUIRED, CONSULT A QUALIFIED ELECTRICIAN OR LOCAL AUTHORITIES FOR CODE REQUIREMENTS.

NOTE: MAKE SURE ALL WIRE CONNECTORS USED ON ELECTRICAL CONNECTIONS ARE SILICONE FILLED.

Now follow instruction sheet (IS-18) make all necessary wiring connections.
After wiring is complete slip post fitter (1) of fixture body (2) over installed post and align holes in post fitter (1) with previously drilled holes in the installed post. Now thread in the three sheet metal screws (4) provided, to secure fixture body to the post.

wiring grounding instructions

SAFETY WARNING: READ WIRING AND GROUNDING INSTRUCTIONS (IS 18) AND ANY ADDITIONAL DIRECTIONS. TURN POWER SUPPLY OFF DURING INSTALLATION. IF NEW

WIRING IS REQUIRED, CONSULT A QUALIFIED ELECTRICIAN OR LOCAL AUTHORITIES FOR CODE REQUIREMENTS

wiring instructions

Indoor Fixtures

Connect positive supply wire (A) (typically black or the smooth, unmarked side of the two-conductor cord) to positive fixture lead ( B ) with appropriately sized twist on connector – **see Drawings 1 or 2.

**

Connect negative supply wire (C) (typically white or the ribbed, marked side of the two-conductor cord) to negative fixture lead (D).
Please refer to the grounding instructions below to complete all electrical connections

Outdoor Fixtures

Connect positive supply wire (A) (typically black or the smooth unmarked side of the two-conductor cord) to positive fixture lead (B) with appropriately sized twist on connector — see Drawings 2 or 3.
Connect negative supply wire (C) (typically white or the ribbed, marked side of the two-conductor cord) to negative fixture lead (D).
Cover open end of connectors with silicone sealant to form a watertight seal.
If installing a wall mount fixture, use caulk to seal gaps between the fixture mounting plate (backplate) and the wall. This will help prevent water from entering the outlet box. If the wall surface is lap siding, use caulk and a fixture mounting platform specially.
Please refer to the grounding instructions below to complete all electrical connections.

grounding instructions

Flush Mount Fixtures
For positive grounding in a 3-wire electrical system, fasten the fixture ground wire (E) (typically copper or green plastic coated) to the fixture mounting strap (M) with the ground screw (S) – see Drawing 1.

Note : On straps for screw supported fixtures, first install the two mounting screws in strap. Any remaining tapped hole may be used for the ground screw.

Chain Hung Fixtures
Loop fixture ground wire (E) (typically copper or green plastic coated) under the head of the ground screw (S) on fixture mounting strap (M) and connect to the loose end of the fixture ground wire directly to the ground wire of the building system with appropriately sized twist-on connectors – see Drawing 2.

Post-Mount Fixtures
Connect fixture ground wire (E) (typically copper or green plastic coated) to power supply ground with appropriately sized twist-on connector inside post. Cover open end of connector with silicone sealant to form a watertight seal – see Drawing 3.

HINKLEY LOGO

Documents / Resources

| HINKLEY 1141OL-CL Casa Large Post Top or Pier Mount Lantern [pdf] Instruction Manual
1141OL-CL Casa Large Post Top or Pier Mount Lantern, 1141OL-CL, Casa Large Post Top or Pier Mount Lantern, Top or Pier Mount Lantern, Mount Lantern, Lantern
---|---