Honeywell RCW250N Decorative Wired Chimes Instruction Manual
- June 17, 2024
- Honeywell
Table of Contents
Honeywell RCW250N Decorative Wired Chimes
Product Information
Specifications
- Product Series : RCW35 and RCW25 Series (51366SL)
- Compatible Models: RCW250N, RCW251N, RCW35N, RCW3501N, RCW3502N, RCW3503N, RCW3504N, RCW3505N, RCW3506N
- Power Options : 4 x LR14C Alkaline Batteries or a 16V, 10VA Transformer
- Maximum Wire Length : 150 ft. (50 m)
Product Usage Instructions
Installation
- Open the chime cover.
- Determine the type of power supply and wired push required for your installation.
- Mount the chime using the marked screw holes.
- Connect the wires from the door push and transformer (if used) to the chime terminals according to the wiring diagram in Step 4.
Power Supply Options
Choose one of the following power supply options:
- Option 1 : Battery Powered – Use 4 x LR14C Alkaline Batteries. Do not use a transformer.
- Option 2 : Transformer Powered – Use a 16V, 10VA transformer. Do not use batteries.
FAQ
- Q: Which bell pushes are compatible with this chime?
- A : This chime is compatible with most bell pushes with standard normally open contacts, including Honeywell wired pushes marked with B.
- Q: Can I use illuminated bell push buttons with this chime?
- A : Yes, illuminated bell push buttons can be used when the chime is powered by a transformer (Honeywell RCA900N).
- Q: How many push circuits can this chime work with?
- A : This chime can work with up to 3 push circuits.
- Q: Can I use rechargeable batteries?
- A : No, only use 4 x LR14C Alkaline Batteries or a 16V, 10VA transformer.
PRODUCT OVERTVIEW
Installation Instructions
Compatible with most bell pushes, with standard normally open contacts,
including Honeywell wired pushes marked with “B.”
Can work with up to 3 push circuits.
Illuminated bell push buttons can be used when the chime is powered by a
transformer (Honeywell RCA900N).
Safety
Before proceeding with the installation, please note the following safety
warnings:
- Always follow the manufacturer’s advice when using power tools and wear suitable protective equipment (e.g. safety goggles) when drilling holes, etc.
- Before drilling holes in walls, check for hidden electricity cables and water pipes. The use of a cable/pipe locator is advisable if in doubt.
- The chime is for indoor use only.
- Avoid mounting location which can expose chime to splashing or dripping liquid.
- Use a UL-approved transformer for connection to mains.
Batteries (battery pack or batteries installed) shall not be exposed to excessive heat such as sunshine, fire or the like; danger of damage if battery is incorrectly replaced. Replace only with the same or equivalent type.
Checking Pack Contents
- Chime
- 2 x fixing screws for chime
- 2 x wall plugs
You will need:
- Wired push
- 20 AWG minimum bell wire
- 4 mm cross-head screwdriver
- A small flat-bladed screwdriver
- 1/4-in. (6 mm) masonry drill bit
- 4 x LR14 ‘C’ Alkaline batteries OR transformer (16V 10 VA) Honeywell part number RCA900N
Installation
- Open the chime cover
- Power Supply
- Determine the type of power supply and type of wired push required to suit your installation. Use 4 x LR14 ‘C’ size alkaline batteries; OR a 16V, 10VA transformer as recommended in the table below below:
- Mount the Chime
- Mounting holes are marked with a screw symbol.
Wiring
Connect the wires from the door push and trans-former (where used) to the chime terminals as detailed in step 4. The wires can be surface mounted or direct from opening in the wall and enter the rear of the chime housing using the wire guide channels provided.
- 4a. Transformer powered – Wiring for standard/lighted push via a 16V 10VA transformer.
OPTION 2: SERIES AC CONNECTION REQUIRED BATTERIES
Note: Wire/cable length should not exceed 150 ft. (50 m).
- 4b. Battery powered – Wiring for standard (non-lighted) push only.
- Note : Wire/cable length should not exceed 150 ft. (50 m).
Operate Push
- 5. The chime will play the default tune. The associated channel LED will illuminate.
- 6. To adjust volume.
To Change Tune
Program Button
8. The Program button can be used to:
- Change the tune of the associated push without pressing the push button. Press and hold the program button l. The channel LED will illuminate in sequence. Release the program button when the channel LED for the related push illuminates. The chime will play the latest tune, channel LED will flash. While the channel LED is flashing, the tune can be changed using the tune select button.
- Recall
A short push of the program button l will flash the Channel LED linked to the last push that was used.
Press the push button, chime will play the tune, while the Channel LED on the
chime is flashing, press and release the tune button . Press and release
button again to cycle through the available tunes until you hear the tune you
want to play.
The last tune played will be stored after the Channel LED stops flashing.
To confirm, press the push button and the chime will play tune you want.
- 9. Clip on the front cover.
- 10. For customizable wood covers only: Choose your paint, wood stain/varnish or wall paper and then apply to the cover. Follow manufacturers’ advice on the paint/vanish.
It is possible to unscrew the four screws shown below for finishing. Ensure
you screw it back with the same screws provided!
Once completed, clip it onto the base.
Installation Instructions
| Specification | Chime |
|---|---|
| Operating Temperature | 32°F to 104°F |
0°C to +40°C
Sound Level (typical)| 90dBA @ 3 ft (1m)
Power Supply| 4 x LR14 C size alkaline batteries OR
16V 10VA transformer (UL approved) Honeywell part number RCA900N
Battery Life (if applicable) (5 operations/day)| 12 months
Troubleshooting
When the illuminated bell push is operated, very dim / no light appears on the
push…Check the power supply. You should use a 16V 10VA transformer connection
for an illuminated push. Follow step 4.
The chime does not work…
-
Check that the wiring is done correctly according to step 4, using a minimum 20AWG wire.
If using batteries: -
Check that the batteries are the correct type, LR14 ‘C’ cells. Only use alkaline batteries.
-
Check that the batteries are fitted correctly (with correct polarity).
-
Check that batteries are not too low.
The chime does not sound… -
Check that the volume control is not at the minimum setting.
Low battery light flashes… -
When the chime battery is low, an amber LED located at the side of the chime will flash. Install new batteries in the chime, type LR14 ‘C’ cells. Only use alkaline batteries.
The icons keep on flashing…
- The push associated with the icon is stuck. Check the push.
Disposal & Recycling
Batteries and waste electrical products should not be disposed of with
household waste. Please recycle where these facilities exist. Check with your
local authority or retailer for recycling advice.
Guarantee
Honeywell guarantees this product for 1 year from the date of purchase. Proof
of purchase is required; this does not affect your statutory rights. If you
require further information about your product, call the Honeywell helpline at
1-800-468-1502.
Declaration
Honeywell hereby declares that this product complies with Part 15 of the FCC rules and Industrial Canada standards. This device operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired operation.
Caution:
Changes or modification not expressly approved by the party responsible for
regulatory compli-ance could void the user’s authority to operate the
equipment.
The Class B digital apparatus complies with Canadian IECS-003. Cet appareil
numérique de la class B est conforme á la norme NMB-003 du Canada.
Honeywell International Inc.
ACS, Environmental and Combustion Controls 1985 Douglas Drive, Golden Valley,
MN 55422 www.honeywell.com
Printed in U.S.A. on recycled paper containing at least 10% post-consumer paper fibers.
- ® U.S. Registered Trademark.
- © 2008 Honeywell International Inc.
- 69-2173EFS—03 M.S. Rev. 04-08
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>