Ufree U-1257 Professional Clippers User Manual
- June 17, 2024
- Ufree
Table of Contents
- Ufree U-1257 Professional Clippers
- Product Information
- Product Usage Instructions
- Components
- Parameters
- Use the Rechargeable Mode
- Fixed-length Function
- Blade Removal&Installation
- Cutter Cleaning
- Fixed-length Function
- Cutter Assembly and Disassembly
- Cutter Cleaning and Maintenance
- Precautions For Use
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
Ufree U-1257 Professional Clippers
Product Information
Specifications
- Model: U-1257
- Product Type: Professional Clipper
- Blade Material: Sharp Stainless Steel
- Battery: High-performance 1200mA Lithium Battery
- Working Voltage: 5V
- Axis Material: Wearable Brass
- Charging Time: About 2.5 Hours
- Operable Time in Full-power: About 3 Hours
- Specific Adapter Input: 100-240V~50/60Hz Output: 5V 1000mA
Product Usage Instructions
Use the Rechargeable Mode
- Insert the charger into the tail of the clipper and connect it to the power source to start charging.
- The liquid crystal indicator will light up, indicating that it has started charging. The indicator will show 100 when the battery is fully charged.
- Note: If the indicator lights up after charging and the charging head is reversed or damaged, it should be replaced immediately.
Fixed-length Function
The clipper comes with 4 limit combs to control hair length:
- 1mm
- 2mm
- 3mm
- 4mm
- To determine the desired haircut length.
- Select the appropriate limit comb.
- To mount the limit comb:
- Align the limit comb with the blade edge.
- Slightly push forward to mount it.
- To disassemble the limit comb, simply pull it hard.
Blade Removal & Installation
Blade Removal:
- Use a screwdriver to remove the rotary cutter head under part.
Blade Installation:
- To prevent the blade from falling, use another hand to hold it.
- Align the blade spring with spring A on the knife head B.
- Put in two fixed screws and hold down.
- Tighten the screws with a screwdriver to ensure the head of the knife will not fall off.
- Note: Do not disassemble the knife head without proper skill.
Cleaning
Taper Blade Cleaning:
Use the provided cleaning brush to clear up the blade.
Note:
- Please do not disassemble the product.
- Do not use water to wash the clipper. Keep it away from dampness while operating.
- Only use a little wet cloth or neutral liquid soap for cleaning.
- After the battery life expires, dispose of the battery at a designated recycling site.
Frequently Asked Questions (FAQ)
-
Q: Can I use the clipper cordless?
A: Yes, the clipper can be used cordless. It has a rechargeable battery. -
Q: How long does it take to fully charge the battery?
A: It takes about 2.5 hours to fully charge the battery. -
Q: How long can I use the clipper on a full charge?
A: The clipper can be used for about 3 hours on a full charge. -
Q: How do I adjust the hair length?
A: The clipper comes with limit combs for different hair lengths. Select the appropriate limit comb and mount it on the blade edge.
Components
Parameters
Use the Rechargeable Mode
- Insert the charger into the tail of the clipper, connect to the power to start charging
- The liquid crystal indicator lights up, indicating that it starts charging. The indicator indicates 100 indicating that the electricity is full.
Note : when the power is switched on after charging, the indicator lights up to indicate that the charging head is reversed or drawn to be replaced immediately.
Fixed-length Function
A: Features ( 1 . 2 . 3 . 4mm ) 4 lengths adjustment to control hair length.
- To determine the length of the haircut
- To select the appropriate limit comb
Mount the limit comb:
- Align the limit comb with the blade edge
- Slightly forward push to mount it Disassemble the limit comb: Just pull hard the limit comb
Blade Removal&Installation
Blade Removal
- Such as a screwdriver with the rotary cutter head under part, remove the cutter head
- To prevent the knife from falling, use another hand to hold it
Blade Installation
- The blade spring is aligned with the spring A on the knife head B. Then, put in two fixed screws, and hold down.
- Tighten the screw with a screwdriver to ensure the head of the knife, Will not fall off.
Warm tip: do not disassemble the knife head without any skill.
Cutter Cleaning
Taper Blade Cleaning
- Clear up the blade with the cleaning brush.
Note
- Please do not disassemble the product.
- Water must not be used to wash the clipper, keep away from the dampness while operating.
- Only use a little wet cloth or neutral liquid soap to clean the product.
- Never charge the product above 40 ℃heat source or below O℃ environment。
- Slight heating during operating or charging is a normal case
- After the battery life expires, take off and safely throw the battery into the designated recycling site. Never dump it randomly.
Components
Parameters
Use the Rechargeable Mode
- Insert the charger into the tail of the clipper, connect to the power to start charging
- When the charging indicator lights up, it starts charging; When shows 100, it is fully charged
- Cord and cordless are available
Fixed-length Function
- A: Use of Limit Comb: Cropped hair and hair trim Feature : ( 1.5,3,4.5,6,10,13 mm ) 6 lengths adjustment control the hair length
- To determine the length of the haircut
- To select the appropriate limit comb
- To fine-tune the cutter Adjust the cutter by rotating the adjusting ring from forward to downward
Mount the limit comb
- Align the limit comb with the blade edge
- Slightly forward push to mount it
Disassemble the limit comb:
Just pull hard the limit comb
Cutter Assembly and Disassembly
Sketch shows how the bottom blade holes are larger than the shanks of the blade screws. When the blade screws are loosened the bottom blade can be aligned tight after the blade is aligned
- The end of the top blade teeth should be 1 / 32 ” to 1 / 16, 0 . 79mm to 1 . 59mm back from the bottom blade. This is important so that the clipper doesn’t cut too close or allow the moving cutter to touch the skin
- The extreme left-hand tooth of the top blade must be covered or be to the left of the first small tooth of the bottom blade
- The extreme right-hand tooth of the top blade must be touching the big tooth on the bottom blade
Taper Lever Some clippers are equipped with an adjustable taper lever that changes the closeness of your cut. When the lever is in the uppermost position the blades will give the closest cut. Pushing the lever downward gradually increases the cutting length
Cutter Cleaning and Maintenance
Blade Alignment
- Your clippers were carefully examined to ensure that the blades were oiled and aligned before leaving our factory
- Blades must be realigned if they have been removed for cleaning or replacement
- To realign the blades, simply match the teeth of the upper and bottom blades up, point for point. ( End of top blade teeth should be approximately 0.5mm-1.0mm back from bottom blade. Compare your clipper blades with the sketch)
- If blade alignment is incorrect, add a few drops of oil to the blade, turn the clipper on for a few moments, turn it off, and unplug. Loosen screws slightly and adjust Tighten screws after the blade is aligned
Cutter Maintenance
- To maintain your clipper in peak condition, the blades should be oiled every few haircuts.
- To oil it properly, the unit should be held so the blades are in a downward position. With the clipper blade running dispense 2-3 drops of oil across the top blade
Precautions For Use
-
Please do not disassemble the product
-
The hair clipper can not be washed
Please keep it away from wet conditions -
The product can only be cleaned by cloth with little water or a mild soap solution
-
Do not charge the product in the environment above 40℃ or below 0℃
- The product can produce little heat during use or charging, which is normal.
- Please remove the battery safely and return it to the specified places when the battery runs out. Never discard it casually
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>