acer AMR210 Vero Wireless Mouse User Guide

acer AMR210 Vero Wireless Mouse

PRODUCT INFORMATION

Specifications

• Left button
• Right button
• Scrolling Wheel
• LED Indicator
• Battery Cover
• Connect Button
• OFF / BT1 / BT2 Switch

Functional Introduction
The Acer Vero Wireless Mouse is equipped with the following features:

1. Left button: Used for left-clicking.
2. Right button: Used for right-clicking.
3. Scrolling Wheel: Used for scrolling up and down.
4. LED Indicator: Provides visual feedback for different states of the mouse.
5. Battery Cover: Allows easy access to the battery compartment.
6. Connect Button: Used to establish a connection with a device.
7. OFF / BT1 / BT2 Switch: Used to switch between different connection modes.

Battery and Power Management
To ensure proper usage of the wireless mouse, follow these steps:

1. Step 1: Take off the battery cover.
2. Step 2: Insert the AA batteries into the battery compartment following the indicated polarity.
3. Step 3: Replace the battery cover.
4. Step 4 : Slide the power switch to the desired position (OFF, BT1, or BT2).
5. Step 5: If you need to travel with the mouse, make sure to turn off the power switch to conserve battery life.
   Warning: Always insert the battery with the correct polarity as labeled on the mouse.

Switch Connection Channel
The mouse can be connected to two devices using the BT1 and BT2 modes:

1. To connect to the first device, switch to BT1 mode.
2. To connect to the second device, switch to BT2 mode.

Connect via Bluetooth in Windows

1. Turn on your PC and go to Start > Settings > Bluetooth & devices > Turn on Bluetooth.
2. Switch the mouse to BT mode and press the Connect Button.
3. Find “AMR210BT5.2” in the list of available devices and press Connect.

Connect via Bluetooth in Mac

1. Click on the Apple menu (top left corner of your screen).
2. Go to System Preferences > Bluetooth and turn Bluetooth on.
3. Find “AMR210BT5.2” in the list of available devices and press Connect.

Connect via Bluetooth in Chromebook

1. Click on the Status Bar located in the bottom right corner of the screen.
2. Turn Bluetooth on, then select “Pair new devices”.
3. Find “AMR210BT5.2” in the list of available devices and press Connect.

LED Indicator
The LED indicator on the mouse provides the following information:

• Bluetooth Mode:
  • Red LED is on for 10 seconds: Power ON.
  • Red LED blinking: Pairing (LED turns off when paired or after 10 minutes of failed pairing).
  • Red LED blinking for 10 seconds: Low battery warning.

Power Saving Features
To conserve battery power, the mouse offers the following power management functions:

• The mouse goes into Saving Mode after a period of inactivity.
• There may be a slight delay while the mouse re-establishes Bluetooth connection from power saving or sleeping mode.

Troubleshooting
If you experience any issues with the mouse, consider the following troubleshooting steps:

1. Make sure no other devices operating in the 2.4 GHz radio spectrum (e.g., Wi-Fi network, mobile telephones) are interfering with the mouse’s connection. If necessary, move their antennas further away from your computer.
2. If the issue persists, consult the dealer or an experienced radio/TV technician for assistance.

Frequently Asked Questions (FAQ)

• How do I change the batteries in the Acer Vero Wireless Mouse?
  To change the batteries, follow the steps outlined in the “Battery and Power Management” section of this user’s guide.

• How many devices can I connect to the mouse?
  The mouse can be connected to two devices using the BT1 and BT2 modes. Refer to the “Switch Connection Channel” section for instructions.

• How do I connect the mouse to a Windows computer?
  Follow the steps provided in the “Connect via Bluetooth in Windows” section of this user’s guide.

• Can I use the mouse with a Mac?
  Yes, the mouse can be connected to a Mac. Refer to the “Connect via Bluetooth in Mac” section for instructions.

• How do I conserve battery power?
  The mouse offers power saving features to help conserve battery power. These features are explained in detail in the “Power Saving Features” section of this user’s guide.

Functional Introduction

1. Left button
2. Right button
3. Scrolling Wheel
4. LED Indicator
5. Battery Cover
6. Connect Button
7. OFF / BT1 / BT2 Switch

Battery and Power Management:

• Step 1: Take the battery cover off.
• Step 2: Insert the batteries as shown inside the battery compartment.

• Step 3: Replace the cover.
• Step 4: Slide the switch to .
• Step 5: If you need to travel with your wireless mouse, made sure you turn off the POWER SWITCH.
  **Warning:
• Please insert the battery with the correct position according to the instruction labeled on the mouse.

Switch Connection Channel

• This Mouse can be paired with 2 different devices.
• Slide the switch to and press the connect button then you can connect to the first device.
• Slide the switch to and press the connect button then you can connect to the second device.

Connect via Bluetooth in windows

1. Turn On your PC, select Start > Settings > Bluetooth & devices > Turn on Bluetooth > Add device > Bluetooth.
2. Mouse switch to BT mode and press Connect Button.
3. Find “AMR210BT5.2” and press connect.

Swift pair

1. Turn on your PC, select Start > Settings > Bluetooth & devices > View more devices > Turn on the Show notifications to connect using Swift Pair.

2. Mouse switch to BT mode and press Connect Button.
3. Windows will show a notification “AMR210BT5.2” and Selecting “Connect” starts pairing.

Connect via Bluetooth in Mac

1. Click on “Apple menu” (top left corner of your screen).
2. Go to System Preferences > Bluetooth > Turn Bluetooth on to set up Bluetooth device and find “AMR210BT5.2” press connect.

Connect via Bluetooth in Chromebook

1. Click on the [Status Bar] located in the bottom right corner of the screen.

2. Turn Bluetooth on > Pair new devices > Find “AMR210BT5.2” and press to connect.

Bluetooth Mode

Power saving features:

• To conserve the battery power, the mouse offers power management functions as below:
• The mouse goes into “Saving Mode” after inactivity. There may be a slight delay while the mouse re-establishes Bluetooth connection from power saving or sleeping mode.

Establishing a Bluetooth Connection

The Bluetooth mouse can work in any Bluetooth environment. Before connecting your Bluetooth mouse with your computer, make sure your computer has a working Bluetooth configuration with Human Interface Device (HID) profile. If your computer does not support Bluetooth, you need to obtain and install a commercially available Bluetooth dongle which converts your computer to a Bluetooth environment.

Troubleshooting

• Mouse does not work upon installation or is not detected Try one or more of the following:

  • Make sure the batteries are installed correctly and turn the switch on. Replace a fresh set of batteries if it still does not work.
  • Verify that the computer is Bluetooth enabled.
  • Press the connection button to reset the Bluetooth connection between your mouse and your computer. Make sure it has been detected by the Operating Systems properly.

• The screen cursor does not move properly
  If your screen cursor lags behind the movement, then your Bluetooth connection may not be able to transmit all of the data from the mouse with the necessary speed. This may be caused by interference from other radio sources, obstructions in the radio wave path, excessive distance from the computer, or a combination of the above. Try the following actions to improve your Bluetooth connection and optimize your mouse performance:

  • Remove any metallic objects from the line of sight between your computer and the Bluetooth mouse.
  • If you are using a computer with a built-in Bluetooth antenna, try reorienting the computer until you get a better data rate.
  • If you are using a Bluetooth dongle, use a USB extension cable and place the Bluetooth dongle onto your desktop or somewhere in sight of your Bluetooth mouse.
  • Move the mouse closer to your Bluetooth dongle.
  • Turn off the mouse and turn it on again for better connection.
  • Disconnect any Bluetooth audio devices, such as headsets, that may be connected to your computer.
    Switch off any other devices operating in the 2.4 GHz radio spectrum, such as Wi-Fi network, mobile telephones, etc., or move their antennas further away from your computer.

Federal Communication Commission Interference Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
  FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Radiation Exposure Statement:
The product comply with the FCC portable RF exposure limit set forth for an uncontrolled environment and are safe for intended operation as described in this manual. The further RF exposure reduction can be achieved if the product can be kept as far as possible from the user body or set the device to lower output power if such function is available.

CE declaration of conformity
Hereby, Acer Inc., declares that this Wireless Mouse is in compliance with the essential requirements and other relevant provisions of Radio Equipment Directive 2014/53/EU, and RoHS Directive 2011/65/EU.

DISPOSAL

Abandonment of waste equipment for EU household users
This symbol on the product or on its packaging indicates that the product must not be disposed of with other household waste. When disposing of used devices, it is your responsibility to bring it to a collection point that recycles used electrical and electronic equipment. The separate collection and recycling of used devices at the time of disposal helps to conserve natural resources and ensures that they are recycled in a manner that protects human health and the environment. For more information about recycling points for used devices, please contact your local city office, household waste disposal service, or the shop where you purchased the product.

EU Declaration of Conformity

Federal Communications Commission Declaration of Conformity

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
The following local Manufacturer /Importer is responsible for this declaration:

• Product: Acer Vero Wireless Mouse
• Model Number: AMR210
• Name of Responsible Party: Acer America Corporation
• Address of Responsible Party: 333 West San Carlos St. Suite 1500 San Jose, CA 95110 U. S. A.
• Contact Person: Acer Representative
• Phone No.: 254-298-4000
• Fax No.: 254-298-4147

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>