HTC HTT-31 Tool Table Instruction Manual
- June 17, 2024
- HTC
Table of Contents
HTC HTT-31 Tool Table
Congratulations
You have just purchased a shop accessory that will help you work safer,
quicker, and easier than ever before. Designed for a lifetime of use, HTC
Products will help you do your best alone!
Warning:
Read Owners Manual carefully and be completely familiar with the correct and
safe operation of each power tool before use. Failure to follow these rules
may result in serious personal injury.
Parts
| Description | Part No. | Qty |
|---|---|---|
| Philips Machine Screw – ‘M6’ x 12mm | 3049P | 24 |
| B Nut with Nylon Inset – ‘M6’ | 3050 | 24 |
| C Lock Washer – ‘M6’ | 3051 | 24 |
| D Philips Wood Screw – ‘M6’ | D908 | 8 |
| E Washer – ‘M6’ | D909 | 8 |
| F Slotted Rubber Feet | G222 | 4 |
| G Legs | 3113 | 4 |
| H Long Center Frame Support | 3116 | 2 |
| I Short Center Frame Support | 3117 | 2 |
| J Long Top Support | 3114 | 2 |
| K Short Top Support | 3115 | 2 |
| L Center Shelf Board | 3112 | 2 |
| M Table Top Left | 3111L | 1 |
| N Table Top Right | 3111R | 1 |
Safety Rules
Using power tools of any kind can be dangerous if safe operating procedures are not followed. Recognizing the hazards of each tool and using them with respect and caution will considerably limit the possibility of personal injury. However, if safety precautions are ignored, personal injury will likely result. Always use common sense – your personal safety‑is your responsibility.
-
Know your power tool. Read and understand the Owner’s Manual and observe
the warnings and instruction labels affixed to the tool. -
Properly ground all tools.
-
Keep guards in place.
-
Remove adjusting keys and wrenches.
-
Keep work area clean and dry.
-
Keep children away.
-
Never leave running machines/tools unattended.
-
Disconnect tools from service.
-
Regularly maintain tools.
-
Use correct tools for the job.
-
Never force a tool.
-
Wear safety apparel.
-
Wear safety glasses/goggles.
-
Never stand or sit on tools.
-
Replace damaged components immediately.
-
Think Safety. Safety is a combination of operator awareness, common sense and alertness at all times.
- All attachments, besides the table top, are done with the following hardware: Phillips Machine Screw A, a lock washer C, and a Nut with a Nylon Inset B.
-
Insert rubber feet F onto ends of legs G.
Notice: the correct end has two rectangular holes. -
Attach the Long Center Frame Support H to the legs G. Repeat again with remaining
parts H and G.
-
Repeat again with remaining parts H and G. Attach the two Short Center Frame Supports I to one of the assembled sides from Step 2.
-
Attach the remaining assembled side from Step 2 to the parts assembled in Step 3 (rubber feet on the floor).
-
Using both holes predrilled at the top of each leg, attach the Long Top Support J.
Repeat on other side. -
Using both holes predrilled at the top of each leg, attach the Short Top Support K. Repeat on other side.
-
Using the (8) supplied Phillips Wood Screws D and the (8) washers attach the table top.
-
Line up predrilled holes in the bottom of the table tops M and N with the slots in the Short Top Supports K.
-
Be sure the measurements printed on the table top match up before attaching.
-
Make sure the table top is flush with the longer sides before tightening*
-
If attaching a machine larger than the table top in closed position, adjust the slats appropriately before tightening.
-
-
Insert the Center Shelf Boards as shown.
• Be sure the measurements printed on the table top match up before attaching.
• Make sure the table top is flush with the longer sides before tightening*
Insert the Center Shelf Boards as shown.
One Year Limited Warranty
Warrantor warrants to the original purchaser that the HTT-31 will be free from
defects in materials and workmanship under normal use and service for a period
of one (1) year from the date of original purchase.
The obligation of this Warranty is limited to repair or replacement, at our
option, of components which prove defective under normal use.
Any product or component claimed to be defective should be sent during
Warranty period, postage prepaid to HTC Products, 1161 Rankin, Troy, Michigan
48083, Attn: Warranty Department, together with a copy of your original dated
sales receipt. Call for authorization number before sending.
This warranty is in lieu of all other express warranties, obligations or
liabilities. ANY
IMPLIED WARRANTIES, OBLIGATIONS OR LIABILITIES, SHALL BE LIMITED IN DURATION
TO THE ONE YEAR PERIOD OF THIS LIMITED WARRANTY.
NO AGENT, REPRESENTATIVE, DEALER, OR EMPLOYEE OF THE COMPANY HAS THE AUTHORITY
TO INCREASE OR ALTER THE OBLIGATIONS OF THIS WARRANTY.
This Warranty shall not apply to any product or component which in the opinion
of the Warrantor has been modified or altered in any way, damaged as a result
of an accident, misuse or abuse, or loss of parts. In no case shall the
Warrantor be liable for any special or consequential damages, or any other
costs or warranty, expressed or implied, whatsoever.
This Warranty gives you specific legal rights, and you may also have other
rights which vary from state to state.
Customer Service Department 800-624-2027 www.htcproductsinc.com
HTC Products 1161 Rankin Troy, Michigan 48083 USA
kwww.htcproductsinc.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>