jura ENA Micro 1 Bean Cup Coffee Machine Instruction Manual

: June 16, 2024
: Jura

jura ENA Micro 1 Bean Cup Coffee Machine

Specifications

Model: ENA Micro 1
Manufacturer: Unknown
Product Type: Coffee Machine
Power Supply: 110-120V, 50-60Hz
Power Consumption: 1450W
Water Tank Capacity: 1.1 liters
Bean Container Capacity: 125 grams
Dimensions: 23cm (W) x 32.3cm (H) x 44.5cm (D)
Weight: 8.8 kg

Product Usage Instructions

Preparing and using for the first time

Setting up the machine

Unpack the ENA Micro 1 and remove all packaging materials.
Place the machine on a stable and level surface.
Ensure that the water tank is clean and filled with fresh water.
Connect the machine to a power outlet.

Filling the bean container

Open the bean container lid.
Pour coffee beans into the container, ensuring not to overfill it.
Close the lid securely.

First-time use

Press the power button to switch on the machine.
The machine will go through an automatic rinsing process.
Wait until the machine is ready for use.

First-time use with filter cartridge activation

If using a filter cartridge, follow the instructions provided with the cartridge to activate it.
Place the activated filter cartridge in the designated compartment of the machine.

First-time use without filter cartridge activation

If not using a filter cartridge, skip the activation step.

Adjusting the grinder

Turn the grinder adjustment knob to the desired setting.
A finer grind produces stronger coffee, while a coarser grind produces milder coffee.

Filling the water tank

Open the water tank lid.
Pour fresh water into the tank up to the maximum level indicated.
Close the lid securely.

Determining the water hardness

Refer to the user manual or contact customer support for instructions on determining water hardness.
Adjust the water hardness setting on the machine accordingly.

Preparation

Ristretto, espresso and coffee

Select your desired coffee type using the control panel.
Place a cup under the coffee spout.
Press the corresponding button for your desired cup size.
The machine will automatically brew your coffee.

Permanently setting the amount of water for the cup size

Press and hold the desired cup size button.
The machine will start brewing coffee.
Release the button when the desired amount of coffee is reached.

Ground coffee

If using ground coffee, remove the bean container and grind chute cover.
Place the desired amount of ground coffee into the designated compartment.
Reassemble the bean container and grind chute cover.
Proceed with the brewing process as usual.

Daily operation

Switching on the machine

Press the power button to switch on the machine.
Wait until the machine is ready for use.

Daily maintenance

Regularly clean the coffee spout, drip tray, and waste container.
Empty and rinse the drip tray and waste container as needed.
Refer to the user manual for detailed cleaning instructions.

Switching off the machine

Press and hold the power button for a few seconds.
The machine will shut down.

Permanent settings in programming mode

Inserting and activating the filter

If using a filter cartridge, follow the instructions provided with the cartridge to insert and activate it.
Place the activated filter cartridge in the designated compartment of the machine.

Setting the water hardness

Refer to the user manual or contact customer support for instructions on setting the water hardness.
Adjust the water hardness setting on the machine accordingly.

FAQs

Q: How often should I clean the machine?
A: It is recommended to clean the machine at least once a week or as needed depending on usage.

Q: Can I use pre-ground coffee with this machine?
A: Yes, you can use pre-ground coffee by removing the bean container and using the designated compartment for ground coffee.

Q: How do I determine the water hardness?
A: Refer to the user manual or contact customer support for instructions on determining water hardness and adjusting the machine accordingly.

Q: Can I adjust the strength of the coffee?
A: Yes, you can adjust the strength of the coffee by adjusting the grinder settings to achieve a finer or coarser grind.

U Make sure that the ENA and the

accept any responsibility for the

mains cable are not located close

consequences of improper use. Before using the machine read

to hot surfaces.
U Be careful to ensure that the
mains cable is not trapped and it

these instructions for use thor-

does not rub against sharp

oughly and completely and comply

edges.

with the instructions they contain. U Never open and repair the

A warranty service is not applicable

machine yourself. Do not modify

for damage or defects caused by

the machine in any way that is nl

non-compliance with the instruc-

not described in these instruc-

tions for use. Keep these instruc-

tions for use. The machine

tions for use close to the machine

contains live parts. If opened,

and pass them on to the next user.

there is a danger of potentially

For your safety

fatal injury. Repairs may only be es carried out by authorised JURA

Please carefully read and observe the important safety information

service centres, using original spare parts and accessories.

set out below.

A defective machine is not safe and pt

To avoid danger of potentially fatal could cause injury or fire. To avoid

electric shock:

damage and any associated risk of

U Never use a machine which is
damaged or has a defective

injury or fire:
U Never allow the mains cable to

mains cable.
U In the event of signs of damage,
for example if there is a smell of

loosely hang down. The mains ru cable could pose a tripping
hazard or become damaged.

29

Important information

U Protect the ENA from environ- U Do not fill the bean container

mental influences such as rain,

with water.

frost and direct sunlight.

U Switch the machine off with the

U Do not immerse the ENA, mains

On/Off button if you are going to

cable or connections in water.

be absent for a longer period of

U Do not put the ENA or any

time and remove the mains plug

individual parts in the dish-

from the power socket.

washer.

U Children may not clean or ser-

U Switch your ENA off before clean- vice the machine unless super-

ing work with the On/Off button. vised by a responsible person.

Always wipe the ENA with a

U Do not allow children to play

damp cloth rather than a wet

with the machine.

one, and protect it from pro-

U Keep children under the age of 8

longed exposure to water splash. away from the machine, or

U Only connect the machine to the supervise them constantly.

mains voltage in accordance

U Children aged 8 and over may

with the information on the

only operate the machine with-

rating plate. The rating plate is

out supervision if they have been

located on the underside of your instructed in how to use it safely.

ENA. Further technical data is

Children must be able to recog-

provided in these instructions for nise and understand the poten-

use (see Chapter 9 `Technical

tial dangers arising from incor-

data’).

rect use.

U Please only use original JURA
maintenance products. Use of products that are not explicitly recommended by JURA could damage the ENA.
U Do not use any coffee beans
treated with additives or caramelised coffee beans.
U Only fill the water tank with
fresh, cold water.

People, including children, who
U do not have the physical, sen-
sory or mental capabilities to use the machine safely or
U are inexperienced or lack knowl-
edge in how to use the machine safely must be supervised by a responsible person when using it, or must be instructed in how to use it

correctly.

30

de

1 Preparing and using for the first time

Safety when handling the CLARIS 1 Preparing and using for the

Blue filter cartridge:

first time

U Filter cartridges should be kept

This chapter provides you with the information

en

out of the reach of children.

you need to use your ENA without any problems.

U Store filter cartridges in a dry

You will prepare your ENA step-by-step to enjoy

place in the sealed packaging.

your first perfect cup of coffee.

U Protect cartridges from heat and E Visit us on the internet. On the JURA

direct sunlight.
U Do not use damaged filter

website (www.jura.com) you will find interesting and up-to-date information on

fr

your ENA and every aspect of coffee.

cartridges.

U Do not open filter cartridges.

Setting up the machine

When setting up your ENA, please note the

following:

it

U Place the machine on a horizontal surface that

is not sensitive to water.
U Choose a spot for your ENA which protects the

machine against overheating. Ensure that the

ventilation slots are not covered.

nl Filling the bean container

CAUTION

Coffee beans which have been treated with

additives (e.g. sugar), ground coffee or freeze-dried

coffee will damage the grinder. T Only use roasted, untreated coffee beans to

es

fill the bean container.

T Remove the aroma preservation cover of the

bean container.

T Remove any dirt or foreign objects from

inside the bean container.

pt

T Fill the bean container with coffee beans.

T Close the bean container.

First-time use
When using the machine for the first time, you can
choose whether you want to operate ENA with or ru
without the CLARIS Blue filter cartridge. If the water hardness is 10 °dH or more, we recommend using the filter cartridge. If you do not know the
31

1 Preparing and using for the first time
hardness of your water, you can find this out first (see Chapter 1 `Preparing and using for the first time Determining the water hardness’).
E The On/Off button also acts as a power switch. When the ENA is switched off, the machine does not consume standby energy.
J WARNING
If the machine is operated with a defective mains cable, there is a danger of potentially fatal electric shock.
T Never use a machine which is damaged or has a defective mains cable.
Precondition: Bean container is filled. T Insert the mains plug into a power socket.
Q T Press the On/Off button to switch the machine on. The Descaling symbol & and the Filter symbol ! are lit up.
E Now decide whether you want to operate your ENA with or without a CLARIS Blue filter cartridge.
First-time use with filter cartridge activation
! T Touch the Filter symbol. The Water Tank symbol M lights up.
T Remove the water tank. T Open the filter holder. T Insert the filter cartridge into the water tank,
exerting slight pressure.
T Close the filter holder. It will click into place audibly.

E After two months, the filter will cease to work. Set the date on the date plate on the filter holder in the water tank.
T Fill the water tank with fresh, cold water and reinsert it. The Filter symbol ! lights up.
! T Touch the Filter symbol. The Y, <, > and ! symbols flash. The filter is rinsed and the water flows directly into the drip tray. Rinsing of the filter stops automatically. The machine heats up. The Y, < and > symbols flash. The machine is rinsed, water flows out of the coffee spout. The rinse stops automatically. The Coffee Grounds Container symbol ? lights up.
T Empty the coffee grounds container and drip tray and rinse with warm water.
T Reinsert the coffee grounds container and the drip tray. The Ristretto Y, Espresso < and Coffee > symbols and the symbol for `strong’ coffee strength _ light up. Your ENA is ready for use.

First-time use without filter cartridge activation

If you do not want to use the CLARIS Blue filter cartridge, you will need to set the water hardness. The following water hardness settings are available:

Water hardness Symbol(s) shown in display

Level 1: 1 15 °dH

1 symbol illuminated Y

Level 2: 16 23 °dH

2 symbols illuminated Y <

Level 3: 24 30 °dH

3 symbols illuminated Y < >

& T Touch the Descaling symbol. The Y, < and & symbols light up.

32

de

1 Preparing and using for the first time

T Touch the Y, < or > symbol to set the

E For a coarser consistency of grind, turn the

water hardness, e.g. symbol Y for `level 1′.

switch to the left, for a finer grind, turn it to

The Y and & symbols light up.

the right.

& T Touch the Descaling symbol. The Water Tank symbol M lights up.
T Place a receptacle under the coffee spout. T Remove the water tank.

en
The consistency of grind is correct if the coffee flows regularly from the coffee spout. In addition a fine, thick crema forms.

T Fill the water tank with fresh, cold water and Example: Change the consistency of grind during

reinsert it.

the preparation of a `strong’ espresso.

T Place a cup under the coffee spout. T Open the cover of the grinder adjustment

fr

switch.

it

The Y, < and > symbols flash. The system

fills with water and the water flows directly

into the drip tray.

The operation stops automatically. The

_ T Touch the symbol for `strong’ coffee

machine heats up. The Y, < and > symbols flash. The

strength.

The `strong’ _ symbol lights up.

nl

machine is rinsed, water flows out of the

< T Touch the Espresso symbol to start

coffee spout. The rinse stops automatically.

preparation.

The Ristretto Y, Espresso < and Coffee >

T Turn the grinder adjustment switch to the

symbols and the symbol for `strong’ coffee

desired position while the grinder is

strength _ light up. Your ENA is ready for

running.

use.

The preset amount of water flows into the

es

cup. Preparation stops automatically.

Adjusting the grinder
You can adjust the grinder on a continuous scale to suit the degree of roast of your coffee.

Filling the water tank
Daily maintenance of the machine and hygiene when handling coffee and water are key to a

CAUTION

perfect coffee result in the cup every time. You

pt

If you adjust the consistency of grind when the

should therefore change the water daily.

grinder is not operating, the grinder adjustment switch could be damaged.
T Only adjust the consistency of grind when the grinder is running.

CAUTION Milk, sparkling mineral water or other liquids can damage the water tank or the machine.
T Only fill the water tank with fresh, cold water. ru

33

2 Preparation

T Remove the water tank and rinse with cold water.

E Before and during the grinding operation
you can select the coffee strength for ristretto Y, espresso < and coffee >: normal’ (;),strong’ (_).

The machine always uses the preset amount of water for the type of coffee in question. You can change this setting (see Chapter 2 `Preparation Permanently setting the amount of water for the cup size’).

T Fill the water tank with fresh, cold water and reinsert it.
Determining the water hardness
You can find out what the water hardness is by using the Aquadur® test strip supplied as standard.
T Hold the test strip briefly (for one second) under running water.
T Shake off the water. T Wait for about one minute. T You will then be able to read the degree of
water hardness from the discolouration of the Aquadur® test strip and the description on the packaging.
The water hardness can now be set.
2 Preparation

Your ENA features an energy-saving mode: Soon after the last preparation, the ENA stops heating up. To indicate that the machine is in energysaving mode, after about 5 minutes the brightness of all the symbols is reduced. The ENA must heat back up before the next preparation.
Coffee tastes best served hot. A cold porcelain cup cools the beverage and impairs the taste. We therefore recommend prewarming the cups. The full coffee aroma can develop only in prewarmed cups. You can purchase a JURA cup warmer from your specialised dealer.
Ristretto, espresso and coffee
Ristretto Y, espresso < and coffee > are all prepared following this model.
Example: Proceed as follows to prepare one coffee. Precondition: Your ENA is ready for use.
T Place a cup under the coffee spout. > T Touch the Coffee symbol to start prepara-
tion. The coffee symbol > and coffee strength symbol (; or _) flash, the preset amount of water flows into the cup. Preparation stops automatically. Your ENA is once more ready for use.

E While a speciality coffee is being prepared, you can stop preparation at any time. Simply touch the symbol for the product in question.

Permanently setting the amount of water for the cup size
It is easy to make permanent settings for the amount of water for all speciality coffees according to the cup size. Adjust the amount once as shown

34

de

3 Daily operation

in the following example. Every time you prepare a All speciality coffees with ground coffee are

drink in the future, this amount of water will be

prepared following this model.

dispensed. Example: Permanently adjust the amount of

Example: Prepare a cup of coffee using ground

coffee.

en

espresso to the cup size.

Precondition: Your ENA is ready for use.

T Place a cup under the coffee spout.

T Place a cup under the dual spout.

T Open the powder chute for ground coffee.

< T Touch the Espresso symbol for about

The Ground Coffee symbol v lights up.

3 seconds until the Ristretto Y and

T Place the filler funnel for ground coffee on

coffee > symbols appear again.

the powder chute.

fr

< T Release the Espresso symbol.

The espresso is prepared. The Espresso

symbol < and coffee strength symbol

(; or _) are flashing.

< T Touch the Espresso symbol as soon as there

is enough espresso in the cup. Preparation stops. The amount of water for

it

one espresso is permanently stored.

The Espresso symbol < and coffee strength symbol (; or _) flash until the machine is
ready for use again.

T Place one level measuring spoon of ground
coffee into the filler funnel. T Close the powder chute for ground coffee.

E You can alter this setting at any time by repeating the above procedure.

The Y, <, > and v symbols flash. The Y, < and > symbols light up.

nl

Ground coffee

tion. The Coffee symbol > flashes, the preset

You can choose to use a second coffee variety, for

amount of water flows into the cup.

example decaffeinated coffee, with the powder

Preparation stops automatically. Your ENA is

chute for ground coffee.

once more ready for use.

es

E Use ground coffee which is not ground too

finely. Very fine coffee can block up the system so that the coffee only comes out in

3 Daily operation

drips. E Never add more than one level measuring

Switching on the machine

spoon of ground coffee.

Daily maintenance of the machine and hygiene

pt

E The desired speciality coffee must be

when handling coffee and water are key to a

prepared within approximately one minute perfect coffee result in the cup every time. You

after filling with the ground coffee.

should therefore change the water daily.

Otherwise the ENA stops the operation and
is once more ready for use. E If you did not add a sufficient amount of
ground coffee, the Y, <, > and v symbols
flash and the ENA stops the operation.

When the machine is switched on, it is automati-
cally rinsed. T Place a receptacle under the coffee spout.
Q T Press the On/Off button to switch the
machine on.

ru

35

4 Permanent settings in programming mode

The Y, < and > symbols flash, the machine heats up. The machine is rinsed, water flows out of the coffee spout. The rinse stops automatically. Your ENA is ready for use.
Daily maintenance
To ensure that you get many years of reliable service out of your ENA and to guarantee the optimum coffee quality, the machine requires daily maintenance.
T Remove the drip tray. T Empty the coffee grounds container and
drip tray and rinse with warm water.
E Always empty the coffee grounds container when the machine is switched on. This is the only way of resetting the coffee grounds counter to zero.
T Reinsert the coffee grounds container and the drip tray.
T Rinse the water tank with clean water. T Wipe the surface of the machine with a
clean, soft, damp cloth (e.g. microfibre cloth).
Switching off the machine
When the ENA is switched off, the system is automatically rinsed if a speciality coffee has been prepared.
T Place a receptacle under the coffee spout. Q T Press the On/Off button.
The Y, < and > symbols flash. The machine is rinsed, water flows out of the coffee spout. The rinse stops automatically. Your ENA is switched off.
E When the ENA is switched off with the On/ Off button, the machine does not consume standby energy.

E If no action is performed on the machine for 30 minutes, the ENA will automatically switch off to save energy.
4 Permanent settings in programming mode
Inserting and activating the filter
Your ENA no longer has to be descaled if you are using the CLARIS Blue filter cartridge. If you did not activate the filter cartridge the first time you used the machine, you can do this now as follows.
E Perform the `inserting the filter’ operation without any interruptions. This will ensure that your ENA always produces its best.
Precondition: Your ENA is ready for use. T Touch the ; and symbols for approximately 2 seconds. The ;, , & and L symbols light up brightly.
! T Touch the Filter symbol for approximately 2 seconds. The Water Tank symbol M lights up.
T Remove the water tank. T Open the filter holder. T Insert the filter cartridge into the water tank,
exerting slight pressure.
T Close the filter holder. It will click into place audibly.
E After two months, the filter will cease to work. Set the date on the date plate on the filter holder in the water tank.

36

de
5 Maintenance

T Fill the water tank with fresh, cold water and & T Briefly touch the Descaling symbol.

reinsert it.

The &, Y and < symbols light up.

The Coffee Grounds Container symbol ?

lights up.

The &, Y, < and > symbols light up.

en

T Empty the drip tray and coffee grounds

& T Touch the Descaling symbol to confirm that

container and reinsert them.

you want to set the water hardness to

The Filter symbol ! lights up.

`level 3′.

! T Touch the Filter symbol to start rinsing of

Your ENA is once more ready for use.

the filter

The Y, <, > and ! symbols flash. The filter

fr

is rinsed.

5 Maintenance

Rinsing of the filter stops automatically. The

Coffee Grounds Container symbol ? lights Your ENA has the following integrated mainte-

up. T Empty the drip tray and coffee grounds
container and reinsert them. The Y, < and > symbols flash, the

nance programmes:
U Cleaning the machine U Descaling the machine U Changing the filter

it

machine heats up. Your ENA is once more

ready for use.

Cleaning the machine

Setting the water hardness

After 180 preparations or 80 switch-on rinses, the ENA will prompt you to clean it.

E If you are using the CLARIS Blue filter cartridge and have activated it, there is no

CAUTION

nl

need to set the water hardness.

If the wrong cleaning agent is used, the machine

could be damaged and/or traces could be left

The harder the water is, the more frequently the

behind in the water.

ENA needs to be descaled. It is therefore important

T Use only original JURA maintenance

to set the water hardness accurately.

products.

The following water hardness settings are available: Water hardness Symbol(s) shown in display

E The cleaning programme lasts approximately 15 minutes.

es

Level 1:

1 symbol illuminated

E Do not interrupt the cleaning programme.

1 15 °dH

Y

The quality of cleaning will be impaired if

Level 2: 16 23 °dH
Level 3:

2 symbols illuminated Y <
3 symbols illuminated

you do so.

E JURA cleaning tablets are available from

pt

specialised dealers.

24 30 °dH

Y < >

Precondition: Your ENA is ready for use. The

Example: Change the water hardness setting from Cleaning symbol L lights up.

level 2′ (Y <) tolevel 3′ (Y < >).

L T Touch the Cleaning symbol for approxi-

Precondition: Your ENA is ready for use. T Touch the ; and _ symbols for approxi-

mately 2 seconds.

The Coffee Grounds Container symbol ?

ru

mately 2 seconds.

lights up.

The ;, _, & and L symbols light up brightly.

37

5 Maintenance
T Empty the drip tray and coffee grounds container and reinsert them. The Cleaning symbol L lights up.
T Place a receptacle under the coffee spout. L T Touch the Cleaning symbol.
The Y, <, > and L symbols flash, water flows out of the coffee spout. The operation is interrupted, the Ground Coffee symbol v lights up. T Open the powder chute for ground coffee and drop in a JURA cleaning tablet.
T Close the powder chute for ground coffee. The Cleaning symbol L lights up.
L T Touch the Cleaning symbol. The Y, <, > and L symbols flash, water flows out of the coffee spout several times. The operation is interrupted, the Coffee Grounds Container symbol ? lights up.
T Empty the drip tray and coffee grounds container and reinsert them. The Y, < and > symbols flash. The machine heats up. Your ENA is once more ready for use.
Cleaning the machine without a prompt: You can initiate the ‘Cleaning the machine’ operation manually at any time as long as the machine is ready for use. Touch the ; and symbols at the same time for approximately 2 seconds. The ;, , L and & or ! symbols light up brightly. Continue with the first prompt (indicated by T) as described in this section.
38

Descaling the machine
The ENA builds up deposits of limescale over time and automatically prompts you to descale it when necessary. The degree of calcification depends on the hardness of your water.
J CAUTION
If the descaling agent comes into contact with the skin or eyes, this can cause irritation.
T Avoid contact with the skin or eyes. T Rinse off the descaling agent with clean
water. Should you get any descaling agent in your eye, see a doctor.
CAUTION If the wrong descaling agent is used, the machine could be damaged and/or traces could be left behind in the water.
T Use only original JURA maintenance products.
CAUTION If the descaling operation is interrupted, there may be damage to the machine.
T Allow the descaling programme to run to the end.
CAUTION If the descaling agent comes into contact with sensitive surfaces (e.g. marble), damage cannot be ruled out.
T Clean up any splashes immediately.
E The descaling programme lasts approximately 40 minutes.
E JURA descaling tablets are available from specialised dealers.
E If you use a CLARIS Blue filter cartridge and this is activated, you will not be prompted to descale.
Precondition: Your ENA is ready for use. The Descaling symbol & lights up. & T Touch the Descaling symbol for approxi-
mately 2 seconds. The Coffee Grounds Container symbol ? lights up.

de

5 Maintenance

T Empty the drip tray and coffee grounds

E If the descaling operation stops unexpect-

container and reinsert them.

edly, rinse the water tank thoroughly.

The Water Tank symbol M flashes. T Remove and empty the water tank. T Completely dissolve the contents of one blis-
ter (three JURA descaling tablets) in a
receptacle holding 500 ml of water. This may
take several minutes.

Descaling the machine without a prompt: You
can initiate the ‘Descaling the machine’ operation
manually at any time as long as the machine is ready for use. Touch the ; and symbols at
the same time for approximately 2 seconds. The ;, , L and & symbols light up brightly.

en

Continue with the first prompt (indicated by T) as

described in this section.

fr

Changing the filter

E After 50 litres of water have flowed through,

the filter will cease to work. Your ENA will

T Pour the solution into the empty water tank

automatically prompt you to change the

it

filter.

and reinsert the tank.

E After two months, the filter will cease to

The Descaling symbol & lights up.

work. Set the date on the date plate on the

& T Touch the Descaling symbol.

filter holder in the water tank.

The Y, <, > and & symbols flash and water

E If the CLARIS Blue filter cartridge is not

flows directly into the drip tray. The operation is interrupted, the Coffee

activated in programming mode, you will

not be prompted to change the filter.

nl

Grounds Container symbol ? lights up. T Empty the drip tray and coffee grounds

Precondition: Your ENA is ready for use. The Filter symbol ! lights up.

container and reinsert them. The Water Tank symbol M lights up. T Remove the water tank and rinse thor-
oughly. T Fill the water tank with fresh, cold water and
reinsert it. The Descaling symbol & lights up. & T Touch the Descaling symbol. The Y, <, > and & symbols flash and water

! T Touch the Filter symbol for approximately
2 seconds. The Water Tank symbol M lights up. T Remove the water tank. T Open the filter holder and remove the old
filter cartridge. T Insert a new filter cartridge into the water
tank, exerting slight pressure.

es

flows directly into the drip tray. The Y, < and > symbols flash and water

pt

flows out of the coffee spout.

The operation is interrupted, the Coffee

Grounds Container symbol ? lights up.

T Empty the drip tray and coffee grounds

container and reinsert them.

Your ENA is once more ready for use.

ru

T Close the filter holder. It will click into place

audibly.

39

Maintenance

E After two months, the filter will cease to work. Set the date on the date plate on the filter holder in the water tank.
T Fill the water tank with fresh, cold water and reinsert it. The Coffee Grounds Container symbol ? lights up.
T Empty the drip tray and coffee grounds container and reinsert them. The Filter symbol ! lights up.
! T Touch the Filter symbol to start rinsing of the filter. The Y, <, > and ! symbols flash. The filter is rinsed. Water flows directly into the drip tray. Rinsing of the filter stops automatically. The Coffee Grounds Container symbol ? lights up.
T Empty the drip tray and coffee grounds container and reinsert them. The machine heats up. Your ENA is once more ready for use.
Changing the filter without a prompt: If the filter is activated, you can initiate the ‘Changing the filter’ operation manually at any time as long as the machine is ready for use. Touch the ; and symbols at the same time for approximately 2 seconds. The ;, , L and ! symbols light up brightly. Continue with the first prompt (indicated by T) as described in this section.

T Rinse the water tank thoroughly. T If you use a CLARIS Blue filter cartridge,
reinsert it. T Fill the water tank with fresh, cold water and
reinsert it.
Cleaning the bean container
Coffee beans may be covered with a slight oil film which remains on the walls of the bean container. These traces may negatively affect the coffee result. For this reason clean the bean container from time to time. Q T Press the On/Off button to switch the
machine off. T Disconnect the mains plug. T Remove the bean container cover. T Remove the coffee beans with a vacuum
cleaner. T Clean the bean container with a soft, dry
cloth. T Fill the bean container with fresh coffee
beans, then close the bean container cover.

Descaling the water tank

Limescale deposits may form in the water tank. To ensure correct function of the machine, descale the water tank from time to time.
T Remove the water tank. T If you use a CLARIS Blue filter cartridge,
remove it. T Descale the tank with a mild conventional
descaling agent in accordance with the manufacturer’s instructions.

40

de
6 Messages on symbol display

6 Messages on symbol display

Message (Symbol(s)

Cause/Result

Action

shown in display)

en

The Water Tank symbol M lights up.

The water tank is empty or not correctly inserted. You cannot prepare any products.

T Fill the water tank (see Chapter 1 `Preparing and using for the first time Filling the water tank’). T Insert the water tank.

The Coffee Grounds

The coffee grounds container is T Empty the coffee grounds

Container symbol ? lights full. No speciality coffees can be container and the drip tray (see

fr

up.

prepared.

Chapter 3 `Daily operation Daily

maintenance’).

The Coffee Grounds

The drip tray is not inserted

T Insert the drip tray.

Container symbol ? flashes. correctly or is not inserted at all.

You cannot prepare any products.

it

The Y, <, >, ; and _ symbols flash.

The aroma preservation cover for the bean container is not fitted or not fitted correctly.

T Fit the aroma preservation cover correctly.

The ;, _, L and & or !

You are in programming mode. T Touch the ; or _ symbol to exit

symbols light up brightly.

programming mode. Your ENA is once more ready for use.

nl

The ENA is ready for use and The ENA is prompting you to the Cleaning symbol L lights clean it.
up.

T Perform cleaning (see Chapter 5 `Maintenance Cleaning the machine’).

The ENA is ready for use and The ENA is prompting you to

T Perform descaling (see Chapter 5

the Descaling symbol & lights descale it. up.

`Maintenance Descaling the

es

machine ‘).

The ENA is ready for use and the Filter symbol ! lights up.

After 50 litres of water have flowed through the CLARIS Blue filter cartridge, it will cease to work.

T Replace the CLARIS Blue filter cartridge (see Chapter 5 `Maintenance Changing the filter’).

Preparing ground coffee:

There is insufficient ground

T The next time you prepare a

After ground coffee is added coffee in the machine; the ENA beverage, add more ground coffee

pt

to the machine, the Y, <, > stops the operation.

(see Chapter 2 `Preparation

and v symbols flash briefly.

Ground coffee’).

ru

41

7 Troubleshooting
7 Troubleshooting

Problem
Coffee only comes out in drips when it is being prepared.

Cause/Result
Coffee or ground coffee has been ground too finely and is blocking the system.

The Water Tank symbol M lights up even though the tank is full.
The ; and _ symbols flash alternately.

The water tank float is trapped.
The system must be filled with water.

Grinder is making a very loud There are foreign objects in

noise.

the grinder.

When the ENA is switched on, the Cleaning symbol L flashes for 5 seconds. The machine then switches off.

If the machine was exposed to the cold for a long period of time, heating is disabled for safety reasons.

E If you were unable to solve the problem, contact customer support in your country (see Chapter 11 `JURA contact details / Legal information’).

Action
T Set the grinder to a coarser setting or use coarser ground coffee (see Chapter 1 Preparing and using for the first time Adjusting the grinder’). T Descale the water tank (see Chapter 5Maintenance Descaling the water tank’).
T Fill the water tank (see Chapter 1 Preparing and using for the first time Filling the water tank’). T Touch the ; or _ symbol. The system fills up with water. T Contact customer support in your country (see Chapter 11JURA contact details / Legal information’).
T Warm the machine at room temperature.

42

de

8 Transport and environmentally friendly disposal

8 Transport and environmentally 9 Technical data

friendly disposal
Transport / Emptying the system

Voltage Power

220 240 V ~,

50 Hz

en

1450 W

Keep the packaging for your ENA. It should be used to protect the machine during transport.

Conformity mark Energy consumption

A S approx. 4.0 Wh

In order to protect the ENA from frost during transport, the system must be emptied.
Precondition: Your ENA is ready for use. T Place a receptacle under the coffee spout. T Touch the ; and symbols for approximately 2 seconds. The ;, , L and & or ! symbols light up brightly. T Remove and empty the water tank. The <, > and M symbols light up.
< T Touch the Espresso symbol

Energy Save Mode `on’

(display symbols slightly less bright)

fr

Pump pressure

Static, max. 15 bar

Holding capacity of water 1.1 l

tank (without filter)

Holding capacity of bean 125 g

container

it

Holding capacity of coffee approx. 9 portions

grounds container

Cable length

approx. 1.1 m

Hot water will continue to flow until the
system is empty. The Water Tank symbol M lights up. Q T Press the On/Off button to switch the
machine off.

Weight

approx. 8.9 kg

Dimensions (W × H × D) 23 × 32.3 × 44.5 cm

nl
Information for testers (repeat test in accordance with DIN VDE 0701-0702): The central grounding

Disposal

point (CGP) is located on the underside of the machine, right next to the mains cable’s connec-

Please dispose of old machines in an environmen- tion point.

tally neutral way.

es

H

Old machines contain valuable, recyclable

materials which should be recycled. Please

therefore dispose of old machines via suitable

collection systems.

pt

ru 43

10 Index
10 Index
A
Addresses 46 Aroma preservation cover
Bean container with aroma preservation cover 27
B
Bean container Bean container with aroma preservation cover 27 Cleaning 40 Filling 31
Bus bar Technical data 43
Button On/Off button 27
C
Central grounding point 43 CLARIS Blue filter cartridge
Changing 39 Inserting and activating the filter 36 Cleaning Bean container 40 Machine 37 Coffee 34 Coffee grounds container 27 Coffee spout Height- adjustable coffee spout 27 Consistency of grind Adjusting the grinder 33 Grinder adjustment switch 28 Contact details 46 Cup grille 27 Customer support 46
D
Descaling Machine 38 Water tank 40
Display Symbol display 28
Display, messages 41 Disposal 43 Drip tray 27

E
Emptying the system 43 Energy Save Mode 34 Errors
Troubleshooting 42 Espresso 34
F
Filling Bean container 31 Water tank 33
Filter Changing 39 Inserting and activating the filter 36
First-time use 31 With filter cartridge activation 32 Without filter cartridge activation 32
G
Ground coffee 35 Powder chute for ground coffee 28
Grounding point 43
H
Height-adjustable coffee spout 27 Hotline 46
I
Instant coffee Ground coffee 35
Internet 31
J
JURA Contact details 46 Internet 31 website 31
M
Machine Cleaning 37 Descaling 38 Setting up 31 Switching off 36 Switching on 35
Mains cable 27 Maintenance 37
Daily maintenance 36 Messages on display 41

44

de
10 Index

P

T

Permanently setting the water for the cup

Technical data 43

en

size 34

Tel 46

Permanent settings in programming mode 36

Transport 43

Powder chute

Troubleshooting 42

Powder chute for ground coffee 28

U

Preparation 34

Use, First-time 31

Coffee 34 Espresso 34

V

fr

Ground coffee 35

Ventilation slots 27

Ristretto 34

W

Problems

Water hardness

Troubleshooting 42

Determining the water hardness 34

Programming mode 36

Setting the water hardness 37

Setting the water hardness 37 Proper use 29

Water tank 27 Descaling 40

it

R
Ristretto 34

Filling 33 Website 31

S

Safety 29

Safety information 29

Settings

nl

Permanent settings in programming

mode 36

Setting up

Setting up the machine 31

Switching off 36

Switching on 35

Symbol

es

Cleaning 28

Coffee 28

Coffee Grounds Container 28

Coffee strength 28

Descaling 28

Espresso 28
Directives The machine complies with the following directives:
U 2006/95/EC Low Voltage Directive U 2004/108/EC Electromagnetic Compatibility U 2009/125/EC Ecodesign Directive U 2011/65/EU RoHS Directive
Technical changes We reserve the right to make technical changes. The diagrams used in these instructions for use are for illustration purposes only and do not represent the original colours of the machine. Some details of your ENA may vary.

Feedback Your opinion is important to us! Use the contact details at www.jura.com.
Copyright The instructions for use contain information which is protected by copyright. It is not permitted to photocopy these instructions for use or translate them into another language without the prior written consent of JURA